INTEX Quick-Fill™ Electric Air Pump
Owner's Manual
Model AP638
Power Source: 6 "C" Cell Batteries (4.5V)
READ AND FOLLOW ALL INSTRUCTIONS BEFORE USING THIS PRODUCT.
WARNING
- Adult use only.
- Do not drop unit into water or expose unit to rain or water.
- Do not direct air stream at face or body.
- Do not obstruct vent holes or open source.
- Do not insert objects into the inflation or deflation connector.
- Do not operate air pump for more than 10 minutes at a time. Let pump cool at least 5 minutes between use.
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
FOLLOW THESE RULES AND ALL INSTRUCTIONS TO AVOID PROPERTY DAMAGE, ELECTRIC SHOCK, BURNS OR OTHER INJURY.
NAMES OF PARTS
- 1. PUMP
- 2. SWITCH
- 3. BATTERY COMPARTMENT COVER
- 4. TRIGGER AND CLIP
- 5. INFLATION CONNECTOR
- 6. DEFLATION CONNECTOR
- 7. NOZZLES
NOTE: Drawings are for illustration purposes only. Actual product may vary. Not to scale.
Diagram Description: A side view of the Intex electric air pump. Key components are labeled: 1. PUMP (the main body of the device), 2. SWITCH (a rocker switch on the side), 3. BATTERY COMPARTMENT COVER (a panel on the bottom), 4. TRIGGER AND CLIP (a lever mechanism on the side), 5. INFLATION CONNECTOR (a port on the side), 6. DEFLATION CONNECTOR (a port on the top), and 7. NOZZLES (various nozzle attachments shown separately).
INSTRUCTIONS
General Precautions and Battery Information
- For maximum power, use alkaline batteries.
- Remove batteries from equipment that will not be used for an extended period.
- Do not mix old and new batteries.
- Do not mix alkaline, standard (Carbon-Zinc), or rechargeable (Nickel-Cadmium) batteries.
- Remove used batteries promptly.
- Do not dispose of the air pump and its batteries in a fire. Check local regulations for proper disposal instructions.
- Keep away from heat or direct sunlight.
- Return the pump and nozzles to the package when not in use.
- No specific air pump maintenance is required.
- Always purchase the correct size and grade of battery suitable for the intended use.
- Replace all batteries of a set at the same time.
- Clean the battery contacts and the device contacts prior to battery installation.
- Ensure batteries are installed correctly with regard to polarity (+ and -).
SAVE THESE INSTRUCTIONS
INSTALL OR REPLACE BATTERIES
- Open the battery compartment cover. (Refer to Figure 1)
- Insert 6 "C" alkaline batteries (NOT INCLUDED) as shown in the drawings inside the battery compartment. (Refer to Figure 2)
- Replace the battery compartment cover. (Refer to Figure 3)
Diagram Description: Figure 1 shows the sequence of opening the battery compartment cover. Figure 2 shows the correct placement and polarity of six "C" cell batteries within the battery compartment. Figure 3 shows the sequence of closing the battery compartment cover.
INFLATION
- Attach the appropriate nozzle to the inflation connector if necessary. Hold the pump against the inflation valve on the item to be inflated. (Refer to Figure 4)
- NOTE: For large items like inflatable boats and large air mattresses, the pump may fit directly into the inflation valves for faster inflation. Use the appropriate nozzle for smaller inflation valves on items like small air mattresses.
- SWITCH ON: Press "I"; SWITCH OFF: Press "0". (Refer to Figure 5)
Diagram Description: Figure 4 illustrates attaching a nozzle to the inflation connector. Figure 5 shows a finger pressing the "I/O" switch to operate the pump.
DEFLATION
- Attach the appropriate nozzle to the deflation connector if necessary. Hold the pump against the inflation valve on the item to be deflated. (Refer to Figure 6)
- NOTE: Similar to inflation, for large items, the pump may fit directly into the valves for faster deflation. Use the appropriate nozzle for smaller valves.
- SWITCH ON: Press "I"; SWITCH OFF: Press "0". (Refer to Figure 5)
Diagram Description: Figure 6 illustrates attaching a nozzle to the deflation connector. Figure 5 shows a finger pressing the "I/O" switch to operate the pump.