OptiTrack Slim 3U Inanasa Vitu Vinavyosonga Haraka
Vipimo
- Bidhaa: Slim 3U
- Utangamano: OptiHub 2, kitovu cha kawaida cha USB au mlango
- Njia ya Kusawazisha: Kebo ya Kuvunja-Kutoka ya Usawazishaji wa RCA
- Utangamano wa Lenzi: Lenzi ya M12, Lenzi ya CS, Lenzi ya C
- Hiari: Plug ya Kichujio au Kibadilisha Kichujio
Sakinisha Programu
Pakua na uendeshe kisakinishi cha hivi punde zaidi kwenye kompyuta yako mwenyeji. Tafadhali tembelea www.optitrack.com/support/downloads/ kwa orodha ya programu inayolingana.
Sanidi Mtandao wa Kamera
Kamera Moja
Connect the Slim 3U camera to a USB port of an OptiHub 2 or generic USB hub or port.
Kamera Nyingi:
Multiple OptiTrack cameras may be synchronized for greater precision, via a RCA Sync Break-out Cable
Kumbuka: Multiple Slim 3U plugged into an OptiHub 2 will not sync with each other (unlike OptiTrack’s Flex 3 and Flex 13 USB cameras)
RCA Sync Break-Out Cable
- When using Slim 3U cameras, all cameras in the sync chain must be of the same type. Mixed sync environments are not supported.
- Plug in RCA Sync Break-Out Cable to each camera (see Diagram 2).
- Connect master device’s “out” connector to slave camera’s “in” connector using a RCA Sync Break-Out Cable (sold separately).
- Anzisha ulandanishi wa kamera kupitia programu.
Install Lens (Optional)
Thread the lens into included lens holder/adapter until finger tight.
- PCB-only Slim 3U camera (no case) only supports M12 lenses.
- Mounting an M12 lens on a Slim 3U camera with the case requires a CS to M12 adapter.
- OptiTrack’s M12 lenses should be installed with the included Wave Spring for secure focusing.
- CS lenses can be installed directly onto the Slim 3U case.
- C lenses require a CS to C adapter before mounting onto the camera case.
Install Filter Plug or Filter Switcher (Optional)
- Insert Filter Plug/Filter Switcher into slot on the side of M12 lens holder (right-side slot if camera is upright and facing you).
- Tighten set screw on right side of plug.
- If Filter Switcher: Plug two-pin connector into jack at top rear of board. Route wire through notch at top of board.
Kumbuka: Perform steps in reverse to uninstall Filter Plug/Filter Switcher.
Vidokezo vya Kiufundi
- Hakikisha vitovu vyote vya USB vinavyotumiwa na kifaa vinaendeshwa kwa nje (chomeka ukutani).
- Kwa utendakazi bora zaidi, tumia kifaa kilicho na OptiTrack's OptiHub 2.
- Watumiaji lazima wawe na mapendeleo ya kiutawala ili kusakinisha viendeshi vya USB kwenye kompyuta zao.
- Muhimu: Slim 3U cameras must have a lens installed to track and capture video.
Je, unahitaji usaidizi?
Piga simu kwa usaidizi wa kiufundi kwa 1-888-965-0435 au tutumie barua pepe kwa support@optitrack.com.
© 2025 NaturalPoint Inc. Haki zote zimehifadhiwa. Inaweza kubadilishwa bila arifa. 08/25
Maswali Yanayoulizwa Mara Kwa Mara
Can I mix different types of cameras in the sync chain?
No, when using Slim 3U cameras, all cameras in the sync chain must be of the same type. Mixed sync environments are not supported.
How do I uninstall the Filter Plug/Filter Switcher?
Perform the installation steps in reverse to uninstall the Filter Plug or Filter Switcher from the camera setup.
Nyaraka / Rasilimali
 |
OptiTrack Slim 3U Inanasa Vitu Vinavyosonga Haraka [pdf] Mwongozo wa Mtumiaji Slim 3U Inanasa Vitu Vinavyosonga Haraka, Slim 3U, Inanasa Vitu Vinavyosonga Haraka, Vitu Vinavyosonga Haraka, Vitu Vinavyosonga |