OptiTrack Slim 3U ចាប់យកវត្ថុដែលមានចលនាលឿន ការណែនាំអ្នកប្រើប្រាស់

ទាញយក និងដំណើរការកម្មវិធីដំឡើងកម្មវិធីចុងក្រោយបំផុតនៅលើកុំព្យូទ័រម៉ាស៊ីនរបស់អ្នក។ សូមទស្សនា www.optitrack.com/support/downloads/ សម្រាប់បញ្ជីកម្មវិធីដែលត្រូវគ្នា។

Setup Camera Network

កាមេរ៉ាតែមួយ
Connect the Slim 3U camera to a USB port of an OptiHub 2 or generic USB hub or port.

កាមេរ៉ាច្រើន៖
Multiple OptiTrack cameras may be synchronized for greater precision, via a RCA Sync Break-out Cable

ចំណាំ៖ Multiple Slim 3U plugged into an OptiHub 2 will not sync with each other (unlike OptiTrack’s Flex 3 and Flex 13 USB cameras)

RCA Sync Break-Out Cable

When using Slim 3U cameras, all cameras in the sync chain must be of the same type. Mixed sync environments are not supported.

Plug in RCA Sync Break-Out Cable to each camera (see Diagram 2).
Connect master device’s “out” connector to slave camera’s “in” connector using a RCA Sync Break-Out Cable (sold separately).

ចាប់ផ្តើមការធ្វើសមកាលកម្មកាមេរ៉ាតាមរយៈកម្មវិធី។

Install Lens (Optional)

Thread the lens into included lens holder/adapter until finger tight.

PCB-only Slim 3U camera (no case) only supports M12 lenses.

Mounting an M12 lens on a Slim 3U camera with the case requires a CS to M12 adapter.
OptiTrack’s M12 lenses should be installed with the included Wave Spring for secure focusing.

CS lenses can be installed directly onto the Slim 3U case.
C lenses require a CS to C adapter before mounting onto the camera case.

Install Filter Plug or Filter Switcher (Optional)

Insert Filter Plug/Filter Switcher into slot on the side of M12 lens holder (right-side slot if camera is upright and facing you).

Tighten set screw on right side of plug.
If Filter Switcher: Plug two-pin connector into jack at top rear of board. Route wire through notch at top of board.

ចំណាំ៖ Perform steps in reverse to uninstall Filter Plug/Filter Switcher.

កំណត់សម្គាល់បច្ចេកទេស

Make sure all USB hubs used with the device are externally powered (plug into wall).
For best performance, use the device with OptiTrack’s OptiHub 2.

Users must have administrative privileges to install the USB drivers on their computer.
សំខាន់: Slim 3U cameras must have a lens installed to track and capture video.

ត្រូវការជំនួយ?
ទូរស័ព្ទទៅផ្នែកជំនួយបច្ចេកទេសនៅ 1-៨៦៦-៤៤៧-២១៩៤ ឬផ្ញើអ៊ីមែលមកយើង support@optitrack.com.
© 2025 NaturalPoint Inc. រក្សាសិទ្ធិគ្រប់យ៉ាង។ ប្រធានបទអាចផ្លាស់ប្តូរដោយគ្មានការជូនដំណឹង។ ០៨/២៥

សំណួរដែលសួរញឹកញាប់

Can I mix different types of cameras in the sync chain?

No, when using Slim 3U cameras, all cameras in the sync chain must be of the same type. Mixed sync environments are not supported.

How do I uninstall the Filter Plug/Filter Switcher?

Perform the installation steps in reverse to uninstall the Filter Plug or Filter Switcher from the camera setup.

ឯកសារ/ធនធាន

OptiTrack Slim 3U ចាប់យកវត្ថុដែលមានចលនាលឿន [pdf] ការណែនាំអ្នកប្រើប្រាស់
Slim 3U ចាប់យកវត្ថុដែលមានចលនាលឿន Slim 3U ចាប់យកវត្ថុដែលមានចលនាលឿន វត្ថុផ្លាស់ទីលឿន វត្ថុផ្លាស់ទី

ឯកសារយោង

សៀវភៅណែនាំអ្នកប្រើប្រាស់

OptiTrack Slim 3U ចាប់យកវត្ថុដែលមានចលនាលឿន

ដំឡើងកម្មវិធី