VEX 249-8581 AIM Coding Robot

Litlhaloso

• Robot Model: 249-8581 VEX AIM Coding Robot
• Controller Model: 269-8230-000 One Stick Controller
• Robot Li-ion Battery Model: NSC1450 (3.7V/800mAh/2.96Wh)
• Controller Li-ion Battery Model: HFC1025 (3.2V/100mAh/0.32Wh

Litaelo tsa Tšebeliso ea Sehlahisoa

Pairing One Stick Controller to AIM Robot:

1. Power On the AIM Robot.
2. Verify that the Robot is in Bluetooth mode:
   • Check the signal strength icon to confirm Bluetooth Mode.
   • If in WIFI Mode:
     1. Go to the Settings menu and press the icon.
     2. Go to the Wi-Fi menu and press the icon.
     3. Press the Wi-Fi On icon to turn Wifi off.
     4. Verify the Robot is in Bluetooth mode by checking the signal strength icon.
3. Eya ho Litlhophiso.
4. Go to Link Controller and Press the Icon.
5. The screen should display once the AIM Robot is in pairing mode.
6. Double-tap tap Power Button on the One Stick Controller to put it in pairing mode.
7. LED should turn orange once the One Stick Controller is in pairing mode.
8. LED should blink green once the controller is paired with the AIM Robot.
9. AIM Robot should show signal strength in the top left corner when connected to the One Stick Controller.

Getting to the e-label:

1. Power On the AIM Robot.
2. Tobetsa aekhone ea Litlhophiso.
3. Press About icon.
4. The e-label icon will be displayed.

TLHOKOMELISO:

• Risk of fire and burns. Do not open, crush, heat above 60°C, or incinerate.
• Do not recharge a battery pack that shows signs of leakage or corrosion.
• Se ke oa lahla betri mollong.
• E tlameha ho hloekisoa hantle.
• U se ke ua tsamaea ka nako e khutšoanyane.
• Never charge batteries unattended or without adult supervision. Do not heat or set a battery on fire.
• Do not disassemble or refit the battery.

Controller Li-ion Battery Model: HFC1025 (3.2V/100mAh/0.32Wh)

TLHOKOMELISO:

• HO KHALELA KOTSI - Likarolo tse nyane.
• E seng bakeng sa bana ba ka tlase ho lilemo tse 3.

Tlhokomeliso: HO KHALELA KOTSI - Likarolo tse nyane.

vexrobotics.com Ages 8+ Ans 8+

Button and Joystick Test

Pair the One Stick Controller to the AIM Robot

1. Power On the AIM Robot.
2. Verify the Robot is in Bluetooth mode.
   a. Check signal strength icon to determine Bluetooth Mode, continue to step 3.b. Check signal strength icon to determine WIFI Mode.
   1. Go to the Settings menu and press the icon.
   2. Go to Wifi menu and press the icon.
   3. Press the “Wifi On” icon to turn Wifi off.
   4. The following icon should be displayed.
   5. Then press the green checkmark to save settings.
   6. Verify the Robot is in Bluetooth mode by checking the signal strength icon.
3. Eya ho Litlhophiso.
4. Go to Link Controller and Press the Icon.
5. The screen below should be displayed once the AIM Robot is in pairing mode.
6. Double-tap the Power Button to put the One Stick Controller in pairing mode.
7. LED should turn orange once the One Stick Controller has entered pairing mode.
8. LED should blink green once the controller is paired with the AIM RoboThe t.
9. AIM Robot should show signal strength in the top left corner when connected to the Once Stick Controller.

Getting to the e-label

1. Power On the AIM Robot.
2. Tobetsa aekhone ea li-setting.
3. Press About icon.
4. The following icon is displayed.

Custom manufactured in China for Innovation First Trading SARL. Distributed in the U.S.A.A., Mexico, Caribbean, Central & South America by VEX Robotics, Inc., 6725 W. FM 1570, Greenville, TX 75402, U.S.A. Distributed in China by Innovation First International (Shenzhen), Ltd., Suite 1205, Galaxy Development Center, 18 Zhongxin 5th Road, Futian, Shenzhen, Guangdong, China 518048. Distributed in other regions by Innovation First Trading SARL, Z.A.E. Wolser G, 315, 3434 – Dudelange, Luxembourg +352 27 86 04 87. Distributed in Canada by / Distribuè au Canada par / Innovation First Trading, LLC, 6725 W. FM 1570, Greenville, TX 75402, U.S.A. ©2024 VEX Robotics, Inc. All rights reserved. Tous droits réservés.

FCC Tlhokomeliso:
This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and operated according toed by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

Ha re re sesebelisoa sena se baka tšitiso e kotsi ho kamohelo ea seea-le-moea kapa ea thelevishene, e ka lekanyetsoang ka ho tima le ho bulela sesebelisoa. Boemong boo, mosebelisi o khothaletsoa ho leka ho lokisa tšitiso ka e le 'ngoe kapa tse ling tsa mehato e latelang:

• Sheba hape kapa o suthise lenakana le amohelang sebakeng se seng.
• Eketsa karohano pakeng tsa thepa le moamoheli.
• Hokela lisebelisoa le seketsoaneng sa potoloho se fapaneng le seo moamoheli a hokahaneng le sona.
• Ikopanye le morekisi kapa setsebi sa radio/TV se nang le boiphihlelo bakeng sa thuso.

Polelo ea FCC:
Sesebelisoa sena se lumellana le karolo ea 15 ea Melao ea FCC. Ts'ebetso e ipapisitse le maemo a mabeli a latelang: (1) Sesebelisoa sena se kanna sa se ke sa baka tšitiso e kotsi, mme (2) sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe e amohetsoeng, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng. Tlhokomeliso: Liphetoho kapa liphetoho yuniti ena e sa amoheloang ka ho hlaka ke lehlakore le ikarabellang bakeng sa tsamaiso li ka hlakola matla a mosebelisi a ho sebelisa sesebelisoa.

Setatemente sa Tumellano ea Indasteri Canada
Sesebelisoa sena sa dijithale sa Sehlopha sa B se lumellana le Canadian ICES-003.

Ts'ebetso e ipapisitse le maemo a mabeli a latelang:

1. Sesebelisoa sena se kanna sa se ke sa baka tšitiso.
2. Sesebelisoa sena se tlameha ho amohela tšitiso efe kapa efe, ho kenyeletsoa tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa.

Sesebelisoa sena se na le li-transmitter/baamoheli ba sa lumelloeng ke laesense ba lumellanang le Li-RSS tse sa lumelloeng ke Boqapi, Saense le Ntlafatso ea Moruo Canada. Ts'ebetso e itšetlehile ka maemo a mabeli a latelang: (1) Sesebelisoa sena se ka 'na sa se ke sa baka tšitiso. (2) Sesebelisoa sena se tlameha ho amohela tšitiso leha e le efe, ho kenyelletsa le tšitiso e ka bakang ts'ebetso e sa batleheng ea sesebelisoa

For more information and to get started with your kit, scan the QR code to get started at teachAIM.vex.com

FAQS

• Q: How do I check the battery models for the Robot and Controller?
  A: The Robot Li-ion Battery Model is NSC1450 (3.7V/800mAh/2.96Wh) and the Controller Li-ion Battery Model is HFC1025 (3.2V/100mAh/0.32Wh).
• Q: How can I verify if the Robot is in Bluetooth mode?
  A: Check the signal strength icon on the Robot to determine if it is in Bluetooth mode. If not, follow the steps to switch from WIFI Mode to Bluetooth Mode as outlined in the instructions.

Litokomane / Lisebelisoa

VEX 249-8581 AIM Coding Robot [pdf] Buka ea Mong'a 249-8581-750, 249-8581, 249-8581-000, 269-8230-000, 249-8581 AIM Coding Robot, 249-8581, AIM Coding Robot, Coding Robot, Robot

Litšupiso

• Bukana ea Mosebelisi