iControls ROC-2HE-UL Reverse Osmosis System Controller

LITS'ELISO

Rea u amohela.
Re leboha ha o rekile molaoli oa iControls.

U entse khetho e ntle ha u khetha iControls. U ka lebella lilemo tsa tšebeletso e se nang mathata. Ka moralo o ipapisitseng le maikutlo a tsoang ho baetapele ba lefapha la RO hammoho le boiphihlelo ba rona ba moralo le tlhahiso ea sistimi ea RO, balaoli ba iControls RO ba sebetsa hantle haholo sehlopheng.

Leha balaoli ba rona ba lokile, ho na le sebaka sa ho ntlafatsa. Haeba u na le boiphihlelo, mohopolo kapa tlhahiso e ntle kapa e mpe re ka thabela ho utloa ho tsoa ho uena. Hape, kea leboha ha u rekile. Rea u amohela ho sechaba sa basebelisi ba iControls.

David Spears Mopresidente, iControls Technologies Inc. david@icontrols.net

Lintho tse kenang

• Liphetoho tsa boemo ba tanka: (2) Ka tloaelo-E Koetsoe. E ka sebelisoa ka sekhahla se le seng.
• Phetoho ea khatello ea inlet: Ka tloaelo-Bula.
• Lockout switch Ka tloaelo-Bula
  Lisebelisoa tsa Tank, Low Pressure le Pretreat ke 50% duty cycle square wave, 10VDC peak @ 10mA max. Li-switches ke likhokahano tse omeletseng feela. Ho sebelisa voltage ho li-terminals tsena ho tla senya molaoli.
• Controller Power: 110-120/208-240 VAC, 60/50Hz (Range: 110-240 VAC)
• Permeate Conductivity: 0-3000 PPM, 0-6000 µs (sensor e tloaelehileng, CP-1, K=.75)
• Feed Conductivity (khetho): 0-3000 PPM, 0-6000 µs (sensor e tloaelehileng, CP-1, K=.75)

Likarolo tsa Potoloho ea Sephetho

• Fepa Solenoid: 1A. Moqtage tšoana le motor/supply voltage.
• Solenoid Flush: 1A. Moqtage tšoana le motor/supply voltage.
• Enjene: 1.0 HP/110-120V, 2.0 HP/208-240V.

Tšireletso ea Potoloho
Relay FuseTlhaloso: F1 5x20mm 2 Amp  BelFuse 5ST 2-R
Hlokomela: Fuse e bontšitsoeng ka holimo ke ea tšireletso ea tlatsetso feela. Tšireletso ea potoloho ea lekala le mekhoa ea ho khaola e tlameha ho fanoa ka ntle.
Sheba Sets'oants'o sa Tšireletso ea Tšimo bakeng sa Litlhoko tsa Tšireletso ea Potoloho ea Lekala.

Tse ding
Boholo: 7" bolelele, 7" bophara, 4" botebo. Nema 4X Polycarbonate Hinged Enclosure.
Boima ba 'mele: 2.6 lb. (Tlhahiso ea Motheo, e sa kenyellelitse likhoele tsa boikhethelo tsa terata,
Tikoloho: joalo-joalo.) 0-50°C, 10-90%RH (e sa nyenyefatseng)

Sekema se Nolofalitsoeng

Molaoli ea fetangview

Tlhaloso ea Molaoli: CPU-4

Lintlha tsa Molaoli: Boto ea Theminale, TB-1 (Rev D2) (Sheba setšoantšo sa 1 bakeng sa schematic)

Kenyelletso ea Probe ea Conductivity

Controller Programming. Ho fihlella menyetla e patiloeng

Controller Programming: Menu Navigation

Ena ke karolo e itseng view ya dimenu tsa ka hare. Lintho tse ling tse ka fetolehang li kenyelletsa: Puo, Alamo e Utloang (ON/OFF), WQ Lass of Signal setting, Hardware & Firmware Version le tse ling.

Lenaneo la taolo: Khetho ea Lenaneo la ROC-2HE

Molaoli o na le litlhophiso tse 4 tse ikhethileng tsa mosebelisi bakeng sa ho hlophisa RO. Litlhophiso tsa fektheri ea de-fault li bonts'itsoe ka tlase. Litlhophiso li ts'oana ntle le ho fapana ha mokhoa oa flush.

• Lenaneo 1, High Pressure flush.
• Lenaneo la 2, Ha ho Flush
• Lenaneo la 3, Permeate Flush, (khatello e tlase, valve e kenang e koetsoe)
• Lenaneo la 4, Khatello e tlase, phepelo ea metsi a fepe
• Sheba leqephe le fetileng bakeng sa litaelo tsa mokhoa oa ho fihlella lenane la ho khetha mananeo ana.
• Sheba Sehlomathiso A bakeng sa tlhaloso e qaqileng ea Parameters le phello ea eona mosebetsing oa RO.

Likarolo tsena li holofalitsoe ka ho sa feleng ka lebaka la monyetla oa pherekano ho basebelisi ba ho qetela tšimong. Li ka nolofalloa ha li hlokahala ka sebopeho sa lenaneo la OEM PC se lumellang liphetoho ho litekanyetso tsohle tse bontšitsoeng ka holimo.

Controller Fault Condition Displays

Ka tlase ke examplintlha le litlhaloso tsa lipontšo tse tsamaeang le maemo a phoso a ka khonehang ho CPU-4. Maemo a phoso a lula a bontša bothata ba mofuta o itseng bo hlokang ho lokisoa. lipontšo li fana ka tlhahisoleseding e lekaneng ho lemoha mohloli oa phoso le ketso e hlokahalang ea ho lokisa.

Phoso e Tlase ea Khatello: (Sistimi e arabela maemong a khatello e tlase ho litlhophiso tsa sistimi)

• Mola oa 1 "Phoso ea litšebeletso"
• Mola oa 2 “Khatello e Tlase ea Phepelo”
• Mola oa 3
• Mola oa 4 "Qala bocha ka MM:SS"

Pele ho Phekola Phoso: (Pretreat Switch e koetsoe e bonts'a bothata ka sistimi ea pretreat).

• Mola oa 1 "Phoso ea Ts'ebeletso"
• Mola oa 2 "Pretreat"
• Mola oa 3
• Mola oa 4 "Sheba Pretreat Sys."

Phoso ea Permeate Conductity: (Permeate conductivity e phahame ho feta alamo setpoint.)

• Mola oa 1 "Phoso ea litšebeletso"
• Mola oa 2 “Permeate TDS xxx ppm” kapa “Permeate Cond xxx uS”
• Mola oa 3 “Alarm SP xxx ppm” kapa “Alarm SP xxx uS”
• Mola oa 4 "Ho Reset Push Off/ON"

Feed Conductivity Fault: (Fepa conductivity e phahame ho feta alamo setpoint.)

• Mola oa 1 "Phoso ea litšebeletso"
• Mola oa 2 “Fepa TDS xxx ppm” kapa “Feed Cond xxx uS”
• Mola oa 3 “Alarm SP xxx ppm” kapa “Alarm SP xxx uS”
• Mola oa 4 "Ho Reset Push Off/ON"

Melaetsa ea Phoso ea Conductivity Probe:

• Mola oa 2 "Ho kena-kenana" - Lerata le fumanoeng ke potoloho ea conductivity, tekanyo e nepahetseng ha e khonehe.
• Mola oa 2 "Over-Range" - Tekanyo ha e lekane bakeng sa potoloho, probe le eona e ka khutsufatsoa
• Mola oa 2 "Probe shorted" - Potoloho e khuts'oane e fumanoe ho sensor ea mocheso ho probe
• Mola oa 2 "Probe ha e fumanoe" - Potoloho e bulehileng e fumanoe ho sensor ea mocheso ka har'a probe (terata e tšoeu le e sa sirelelitsoeng)
• Mola oa 2 "Probe Startup 1" – Tšupiso ea ka hare voltage phahame haholo ho etsa tekanyo e nepahetseng
• Mola oa 2 "Probe Startup 2" – Tšupiso ea ka hare voltage tlase haholo hore o ka etsa tekanyo e nepahetseng
• Mola oa 2 "Probe Startup 3" – Tsoelo-pele ea ka hare voltage phahame haholo ho etsa tekanyo e nepahetseng
• Mola oa 2 "Probe Startup 4" – Tsoelo-pele ea ka hare voltage tlase haholo hore o ka etsa tekanyo e nepahetseng

Sehlomathiso B. Controller Programming: Programming Interface Overview

Sebopeho sa Lenaneo ke sesebelisoa se thehiloeng ho Windows sa ho etsa liphetoho ho software ea ROC. Skrine sena se bonts'a li-setting tsa RO tse fumanehang. Ho na le lihlopha tse 4 tse ka khethoang tšimong tse bolokiloeng ho CPU-.4

Sehlomathiso C. Tiisetso

Tiisetso ea iControls Limited

Seo tiisetso e se akaretsang:
iControls e fana ka tumello ea hore ROC 2HE e se ke ea e-ba le mefokolo ea thepa le mesebetsi ea matsoho nakong ea ntoa. Haeba sehlahisoa se bonahala se sa sebetse nakong ea waranti, iControls e tla khona ho lokisa khetho feela kapa ho nkela sehlahisoa sebaka ka sehlahisoa se tšoanang. Sehlahisoa se seng kapa likarolo tse ling li ka kenyelletsa likarolo tse nchafalitsoeng kapa tse nchafalitsoeng.

Tiisetso e sebetsa nako e kae:
ROC 2HE e tiiselitsoe selemo se le seng (1) bakeng sa likarolo le mosebetsi ho tloha ka letsatsi la theko ea pele ea bareki kapa likhoeli tse 15 ho tloha ka letsatsi la sekepe, ho sa tsotellehe hore na ke efe e tlang pele.
Seo tiisetso e sa se koaheleng:

1. Tšenyo, ho senyeha kapa ho se sebetse hantle ho bakoang ke:
   • a. Kotsi, tšebeliso e mpe, bohlasoa, mollo, metsi, lehalima kapa liketso tse ling tsa tlhaho, phetoho e sa lumelloeng ea lihlahisoa kapa ho hloleha ho latela litaelo tse fanoeng ka sehlahisoa.
   • b. Ho lokisa kapa ho leka ho lokisoa ke mang kapa mang ea sa lumelloang ke iControls.
   • c. Tšenyo efe kapa efe ea sehlahisoa ka lebaka la ho romelloa.
   • d. E bakang kantle ho sehlahisoa joalo ka ho feto-fetoha ha matla a motlakase.
   • e. Tšebeliso ea lisebelisoa kapa likarolo ha li kopane le litlhaloso tsa iControls.
   • f. Ho qhoma ho tloaelehileng.
   • g. Lebaka le leng le le leng le sa amaneng le bothata ba sehlahisoa.
2. Litšenyehelo tsa lipalangoang tse hlokahalang ho fumana litšebeletso tlas'a tiisetso ena.
3. Mosebetsi o mong ntle le oa feme.

Mokhoa oa ho fumana litšebeletso

1. Ho fumana tšebeletso ea tiisetso, ikopanye le iControls bakeng sa Return Material Authorization (RMA).
2. U tla tlameha ho fana ka:
   • a. Lebitso la hao le aterese
   • b. Tlhaloso ea bothata
3. Kopanya molaoli ka hloko bakeng sa thomello 'me u e khutlisetse ho iControls, thepa e lefelloang esale pele.

Tekanyetso ea li-waranti tse boletsoeng
Ha ho na litiisetso, tse hlahisitsoeng kapa tse boletsoeng, tse fetelang ka nqane ho tlhaloso e fanoeng mona ho kenyeletsoa le tiisetso e boletsoeng ea khoebo le ho sebetsa molemong o itseng.

Kenyelletso ea litšenyehelo
Boikarabello ba iControls bo lekanyelitsoe ho litšenyehelo tsa ho lokisa kapa ho nkela sehlahisoa sebaka. iControls e ke ke ea ikarabella bakeng sa:

1. Tšenyo ea thepa e 'ngoe e bakiloeng ke bofokoli bofe kapa bofe sehlahisoa, ts'enyehelo e ipapisitseng le tšitiso, tahlehelo ea tšebeliso ea sehlahisoa, tahlehelo ea nako, tahlehelo ea phaello, tahlehelo ea monyetla oa khoebo, tahlehelo ea kamohelo, ho kena-kenana le likamano tsa khoebo kapa khoebo e ngoe. tahlehelo, leha a eletsoa ka monyetla kapa ts'enyehelo e joalo.
2. Tšenyo leha e le efe e 'ngoe, ebang ke ea tšohanyetso, e bakoang kapa e seng joalo.
3. Kopo efe kapa efe khahlanong le moreki ke mokha ofe kapa ofe.

Phello ea molao oa naha
Tiisetso ena e u fa litokelo tse khethehileng tsa molao, hape u ka ba le litokelo tse ling tse fapaneng ho ea ka linaha. Linaha tse ling ha li lumelle meeli ea litiisetso tse boletsoeng le/kapa ha li lumelle ho qheleloa ka thoko ho tšenyeho ea tšohanyetso kapa ea litlamorao, ka hona, meeli le mekhelo e kaholimo e kanna ea se sebetse ho uena.

iControls Technologies Inc. 1821 Empire Industrial Court, Suite A Santa Rosa, CA 95403
ph 425-577-8851
www.icontrols.net

Litokomane / Lisebelisoa

iControls ROC-2HE-UL Reverse Osmosis System Controller [pdf] Bukana ea Mosebelisi ROC-2HE-UL, Reverse Osmosis System Controller, ROC-2HE-UL Reverse Osmosis System Controller, Osmosis System Controller, Mookameli oa Tsamaiso, Mookameli

Litšupiso

• Bukana ea Mosebelisi