iControls ROC-2HE-UL Reverse Osmosis System Controller

MALANGIZO

Takulandirani.
Zikomo pogula chowongolera cha iControls.

Munapanga chisankho chabwino posankha iControls. Mukhoza kuyembekezera zaka zambiri za utumiki wopanda mavuto. Ndi mapangidwe otengera mayankho ochokera kwa atsogoleri mu gawo la RO kuphatikiza zomwe takumana nazo pakupanga ndi kupanga makina a RO, owongolera a iControls RO ndiabwino kwambiri m'kalasi.

Ngakhale olamulira athu ali abwino, nthawi zonse pali malo oti tiwongolere. Ngati muli ndi chidziwitso, lingaliro kapena ndemanga zabwino kapena zoyipa, tikufuna kumva kuchokera kwa inu. Apanso, zikomo chifukwa chogula. Takulandilani kugulu la ogwiritsa ntchito iControls.

David Spears Purezidenti, iControls Technologies Inc. david@icontrols.net

Zolowetsa

• Kusintha kwa matanki: (2) Nthawi zambiri-Kutseka. Itha kugwiritsidwa ntchito ndi switch imodzi yokha.
• Inlet pressure switch: Nthawi zambiri-Otsegula.
• Kusintha kwa Pretreat Lockout: Nthawi zambiri-Otsegula
  Zolowetsa za Tank, Low Pressure ndi Pretreat ndi 50% duty cycle square wave, 10VDC peak @ 10mA max. Zolowetsa zosinthira ndizolumikizana zouma zokha. Kugwiritsa ntchito voltage ku ma terminals awa adzawononga wowongolera.
• Mphamvu Yowongolera: 110-120/208-240 VAC, 60/50Hz (Range: 110-240 VAC)
• Permeate Conductivity: 0-3000 PPM, 0-6000 µs (sensor wamba, CP-1, K=.75)
• Feed Conductivity (kusankha): 0-3000 PPM, 0-6000 µs (sensor wamba, CP-1, K=.75)

Zotulutsa Zozungulira

• Zakudya za Solenoid: 1A. Voltage ndi yofanana ndi mota/supply voltage.
• Solenoid Flush: 1A. Voltage ndi yofanana ndi mota/supply voltage.
• Njinga: 1.0 HP/110-120V, 2.0 HP/208-240V.

Chitetezo Chozungulira
Relay Fusekukula: F1x5mm 20 Amp  BelFuse 5ST 2-R
Zindikirani: Fuse yomwe yawonetsedwa pamwambapa ndi yachitetezo chowonjezera chokha. Chitetezo cha dera la nthambi ndi njira zolumikizira ziyenera kuperekedwa kunja.
Onani Chifaniziro cha Mawaya a Munda cha Zofunikira pachitetezo cha Dera la Nthambi.

Zina
Makulidwe: 7" wamtali, 7" m'lifupi, 4" kuya. Nema 4X Polycarbonate Hinged Enclosure.
Kulemera kwake: 2.6 lb
Chilengedwe: ndi zina..) 0-50°C, 10-90%RH (osasunthika)

Chiwembu Chosavuta

Controller Overview

Tsatanetsatane wa Wowongolera: CPU-4

Tsatanetsatane Wowongolera: Terminal Board, TB-1 (Rev D2) (Onani mkuyu 1 wa schema)

Kuyika kwa Conductivity Probe

Controller Programming. Kulowa menyu obisika

Controller Programming: Menu Navigation

Ichi ndi tsankho view za menyu wamkati. Zinthu zina zomwe zingasinthidwe ndi izi: Chinenero, Alamu Yomveka (KUYA/KUZIMU), WQ Kutayika kwa Ma Signal, Hardware & Firmware Version ndi zina zambiri.

Kukonzekera kwa Pulogalamu: ROC-2HE Program Selections

Wowongolera ali ndi magawo anayi osankhidwa osankhidwa ndi ogwiritsa ntchito kuti akonze RO. Zokonda pafakitale za de-fault zikuwonetsedwa pansipa. Zokonda ndizofanana kupatula kusiyana kwa machitidwe a flush.

• Pulogalamu 1, High Pressure flush.
• Pulogalamu 2, Palibe Flush
• Pulogalamu 3, Permeate Flush, (kutsika kochepa, valavu yolowera yotsekedwa)
• Pulogalamu 4, Low Pressure, kudyetsa madzi
• Onani tsamba lapitalo kuti mupeze malangizo amomwe mungapezere menyu posankha mapulogalamuwa.
• Onani Zowonjezera A kuti mumve zambiri za Parameters ndi momwe amakhudzira ntchito ya RO.

Zinthu izi zimayimitsidwa mwachisawawa chifukwa cha kuthekera kwa chisokonezo kwa ogwiritsa ntchito kumapeto. Zitha kuyatsidwa zikafunika kudzera pa mawonekedwe a OEM PC omwe amalola kusintha kwazinthu zonse zomwe zawonetsedwa pamwambapa.

Controller Fault Condition Zowonetsa

M'munsimu muli examples ndi mafotokozedwe a zowonetsera zomwe zimatsagana ndi zolakwika zomwe zingatheke pa CPU-4. Zolakwika nthawi zonse zimasonyeza vuto lamtundu wina lomwe limafuna kuchitapo kanthu. zowonetsera zimapereka chidziwitso chokwanira kuti azindikire gwero la cholakwacho ndi zomwe zimafunika kuwongolera.

Low Pressure Fault: (Dongosolo likuyankha kutsika kwapakatikati pamakina aliwonse)

• Mzere 1 "Zolakwika za Service"
• Mzere 2 “Low Feed Pressure”
• Mzere 3
• Mzere 4 "Yambitsaninso mu MM:SS"

Pre Treat Fault: (Pretreat Switch yatsekedwa kusonyeza vuto ndi pretreat system).

• Mzere 1 "Zolakwa za Utumiki"
• Mzere 2 "Pretreat"
• Mzere 3
• Mzere 4 "Onani Pretreat Sys."

Kulakwitsa kwa Permeate Conductity: (Permeate conductivity ndi yapamwamba kuposa ma alarm setpoint.)

• Mzere 1 "Zolakwika za Service"
• Mzere 2 “Permeate TDS xxx ppm” kapena “Permeate Cond xxx uS”
• Mzere 3 “Alamu SP xxx ppm” kapena “Alamu SP xxx uS”
• Mzere 4 "Kukhazikitsanso Push OFF / ON"

Kuwonongeka kwa Feed Conductivity: (Kudyetsa chakudya ndikokwera kwambiri kuposa ma alarm setpoint.)

• Mzere 1 "Zolakwika za Service"
• Mzere 2 “Dyetsani TDS xxx ppm” kapena “Feed Cond xxx uS”
• Mzere 3 “Alamu SP xxx ppm” kapena “Alamu SP xxx uS”
• Mzere 4 "Kukhazikitsanso Push OFF / ON"

Mauthenga Olakwika a Conductivity Probe:

• Mzere 2 "Kusokoneza" - Phokoso lodziwika ndi dera la conductivity, kuyeza koyenera sikutheka.
• Mzere 2 "Owonjezera" - Kuyeza kwapang'onopang'ono kwa dera, kafukufuku atha kufupikitsidwa
• Mzere 2 "Probe yafupikitsidwa" - Dera lalifupi limapezeka pa sensor ya kutentha mu probe
• Mzere 2 "Kufufuza sikunazindikirike" - Waya wotseguka wopezeka pa sensor ya kutentha mu probe (waya yoyera komanso yopanda chitetezo)
• Mzere 2 "Probe Startup 1" - Buku la mkati voltagndi okwera kwambiri kuti asapange muyeso woyenera
• Mzere 2 "Probe Startup 2" - Buku la mkati voltagndi otsika kwambiri kuti asapange muyeso woyenera
• Mzere 2 "Probe Startup 3" - Chisangalalo chamkati voltagndi okwera kwambiri kuti asapange muyeso woyenera
• Mzere 2 "Probe Startup 4" - Chisangalalo chamkati voltagndi otsika kwambiri kuti asapange muyeso woyenera

Appendix B. Controller Programming: Programming Interface Overview

Mawonekedwe a Programming ndi chida chokhazikitsidwa ndi Windows chosinthira mapulogalamu a ROC. Chophimba ichi chikuwonetsa makonda a RO omwe alipo. Pali ma seti 4 osankhidwa omwe amasungidwa mu CPU-.4

Zowonjezera C. Chitsimikizo

Chitsimikizo cha iControls Limited

Zomwe chitsimikizo chimakwirira:
iControls imatsimikizira ROC 2HE kuti ikhale yopanda zilema muzinthu ndi ntchito pa nthawi ya nkhondo. Ngati chinthu chikuwoneka kuti chili ndi vuto panthawi ya chitsimikizo, iControls idzakonza njira yokhayo yokha kapena m'malo mwa chinthucho ndi chinthu chofanana. Zosintha kapena zigawo zitha kuphatikiza zida zopangidwanso kapena zokonzedwanso.

Nthawi yayitali bwanji chitsimikizo chimagwira ntchito:
ROC 2HE ndiyovomerezeka kwa chaka chimodzi (1) cha magawo ndi ntchito kuyambira tsiku loyamba kugula ogula kapena miyezi 15 kuyambira tsiku la sitimayo, zilizonse zomwe zimabwera poyamba.
Zomwe chitsimikizo sichimakhudza:

1. Kuwonongeka, kuwonongeka kapena kusagwira bwino ntchito chifukwa cha:
   • a. Ngozi, kugwiritsa ntchito molakwika, kunyalanyaza, moto, madzi, mphezi kapena zochitika zina zachilengedwe, kusinthidwa kosaloledwa kapena kulephera kutsatira malangizo operekedwa ndi mankhwalawa.
   • b. Konzani kapena kuyesa kukonzedwa ndi aliyense wosaloledwa ndi iControls.
   • c. Kuwonongeka kulikonse kwa mankhwalawa chifukwa chotumizidwa.
   • d. Zimayambitsa kunja kwa mankhwala monga kusinthasintha kwa magetsi.
   • e. Kugwiritsa ntchito zinthu kapena zigawo zomwe sizikugwirizana ndi zomwe iControls's.
   • f. Kuwonongeka kwanthawi zonse.
   • g. Chifukwa china chilichonse chomwe sichikukhudzana ndi vuto la mankhwala.
2. Mtengo wamayendedwe ofunikira kuti mupeze chithandizo pansi pa chitsimikizochi.
3. Ntchito zina osati za fakitale.

Momwe mungapezere ntchito

1. Kuti mupeze chithandizo cha chitsimikizo, funsani iControls for Return Material Authorization (RMA).
2. Muyenera kupereka:
   • a. Dzina lanu ndi adilesi
   • b. Kufotokozera vuto
3. Phukusini chowongolera mosamala kuti mutumize ndikubweza ku iControls, zolipiriratu zonyamula.

Kulepheretsa kwa zitsimikizo
Palibe zitsimikizo, zofotokozedwa kapena kutanthauza, zomwe zimapitilira zomwe zili pano kuphatikiza chitsimikizo cha malonda ndi kulimba pazifuno zinazake.

Kupatula zowonongeka
Ngongole ya iControls imangokhala pamtengo wokonzanso kapena kusinthanso chinthucho. iControls sadzakhala ndi mlandu:

1. Kuwonongeka kwa katundu wina chifukwa cha vuto lililonse la malonda, zowonongeka chifukwa cha kusokoneza, kutaya ntchito, kutaya nthawi, kutaya phindu, kutaya mwayi wamalonda, kutaya chidwi, kusokoneza ubale wamalonda kapena malonda ena. kutaya, ngakhale atalangizidwa za kuthekera kapena kuwonongeka kotere.
2. Zowonongeka zina zilizonse, kaya mwangozi, zotsatila kapena ayi.
3. Kudandaula kulikonse motsutsana ndi kasitomala ndi gulu lina.

Zotsatira za malamulo a boma
Chitsimikizochi chimakupatsani maufulu enieni azamalamulo, komanso mutha kukhala ndi maufulu ena omwe amasiyana malinga ndi boma. Mayiko ena salola malire pa zitsimikizo zomwe akunenedwazo komanso/kapena salola kuchotsedwa kwa zowonongeka mwangozi kapena zotsatira zake, kotero zoletsa zomwe zili pamwambazi sizingagwire ntchito kwa inu.

iControls Technologies Inc. 1821 Empire Industrial Court, Suite A Santa Rosa, CA 95403
ph 425-577-8851
www.icontrols.net

Zolemba / Zothandizira

iControls ROC-2HE-UL Reverse Osmosis System Controller [pdf] Buku Logwiritsa Ntchito ROC-2HE-UL, Reverse Osmosis System Controller, ROC-2HE-UL Reverse Osmosis System Controller, Osmosis System Controller, System Controller, Controller

Maumboni

• Buku Logwiritsa Ntchito