eFlow104NA8 Series Dual Output
Fumana Balaoli ba Matla
Tataiso ea ho Kena

eFlow104NA8 Series Dual Output Access Power Controllers

eFlow104NKA8

• 12VDC kapa 5VDC ho fihla ho 6A le / kapa 24VDC ho fihla ho 10A (240W kakaretso ea matla) e khethiloeng ka tlhahiso.
• Liphetho tse robeli (8) tse sirelelitsoeng ka fuse.
• Tse robeli (8) tse khethiloeng tsa Fail Safe, Fail-Secure, kapa Foromo ea "C" e omileng
• Alamo ea Mollo Hakolla khetho ka tlhahiso
• Charger e kentsoeng kahare bakeng sa asiti ea lead e tiisitsoeng kapa libeteri tsa mofuta oa gel

eFlow104NKA8D

• 12VDC kapa 5VDC ho fihla ho 6A le / kapa 24VDC ho fihla ho 10A (240W kakaretso ea matla) e khethiloeng ka tlhahiso.
• Liphetho tse sirelelitsoeng ke PTC tse nang le matla a lekanyelitsoeng a Sehlopha sa Borobeli (8).
• Tse robeli (8) tse khethiloeng tsa Fail Safe, Fail-Secure, kapa Foromo ea "C" e omileng.
• Fire Alarm Disconnect e ka khethoa ka tlhahiso.
• Charger e kentsoeng kahare bakeng sa asiti ea lead e tiisitsoeng kapa libeteri tsa mofuta oa gel.

Rev. eFlow104NKA8-072220

Khampani ea ho Kenya: _______________ Moemeli oa Tšebeletso Lebitso: ______________________________
Aterese: _____________________________________________ Nomoro ea mohala: ______________________________

Fetileview:

Altronix eFlow104NKA8 le eFlow104NKA8D li aba le ho fetola matla ho fihlella litsamaiso tsa taolo le lisebelisoa. Ba fetola tlhahiso ea 120VAC 60Hz ho tse robeli (8) tse laoloang ka boikemelo tsa 12VDC kapa 24VDC tse sirelelitsoeng. Moralo oa ho kenya habeli oa Access Power Controller o lumella matla ho tsamaisoa ho tloha ho tse peli (2) tse kentsoeng fekthering tse tlase tse ikemetseng.tage 12 kapa 24VDC Altronix phepelo ea matla ho tse robeli (8) tse laoloang ka mokhoa o ikemetseng (eFlow104NKA8) kapa PTC (eFlow104NKA8D) tse sirelelitsoeng. Lisebelisoa tsa motlakase li ka fetoloa ho mabitso a "C" a omileng. Lintho tse hlahisoang li hlahisoa ke sink e bulehileng ea pokello, hangata e butsoe (NO), hangata e koetsoeng (NC) e omileng ea ho kenya letsoho, kapa metsi a tsoang ho Access Control System, Card Reader, Keypad, Push Button, PIR, joalo-joalo eFlow104NKA8(D) e tla matla a tsela ho ea ho lisebelisoa tse fapaneng tsa ho laola lisebelisoa tsa lisebelisoa tse kenyeletsang Mag Locks, Litlhaselo tsa Motlakase, Magnetic Door Holders, joalo-joalo Liphetho li tla sebetsa ka mekhoa e 'meli ea Fail-Safe le / kapa Fail-Secure. FACP Interface e nolofalletsa Emergency Egress, le Alarm Monitoring, kapa e ka sebelisoa ho kenya lisebelisoa tse ling tse thusang. Tšobotsi ea ho khaola alamo ea mollo e ka khethoa ka bonngoe bakeng sa liphetho leha e le life kapa kaofela tse robeli (8). Lihokelo tsa li-spade li u lumella ho kenya matla a marang-rang ho li-module tse ngata tsa ACMS8(CB). Karolo ena e u lumella ho aba matla holim'a liphetho tse ngata bakeng sa litsamaiso tse kholoanyane.

Litlhaloso tsa Boemo:

Betri	Burg. Lisebelisoa 4 hora. Ema haufi/ 15 mets. Alamo	Likopo tsa Mollo 24 hora. Ema haufi/ 5 mets. Alamo	Taolo ea ho fihlella Lisebelisoa Ema haufi
7AH	0.4A/10A	N/A	5 mets./10A
12A11	1A/10A	0.3A/10A	15 mets./10A
40A11	6A/10A	1.2A/10A	Ho feta lihora tse 2/10A
65A11	6A/10A	1.5A/10A	Ho feta lihora tse 4/10A

Litlhaloso:

Kenyelletso:
eFlow104NB:

• 120VAC, 60Hz, 4.5A.
  ACMS8/ACMS8CB:
• Litlhahiso tse robeli (8):
  a) Ka tloaelo bula (NO) tse kenang (mabitso a omileng).
  b) Lisebelisoa tse tloaelehileng tse koetsoeng (NC) (li-contacts tse omileng).
  c) Bula lisebelisoa tsa sink ea pokello.
  d) Kenyelletso ea Metsi (5VDC - 24VDC) e nang le mohanyetsi oa 10K
  e) Motsoako ofe kapa ofe oa tse ka holimo.

Liphetho:
Matla:

• 12VDC kapa 5VDC ho fihla ho 6A, 24VDC ho fihla ho 10A
  (240W kakaretso ea matla).
• Thuso ea Sehlopha sa 2 se nang le matla a fokolang
  rated @ 1A (ha e so fetohe).
• Ho tlolatagtshireletso.
  ACMS8:
• Liphetho tse sirelelitsoeng ka fuse li behiloe @ 2.5A ka tlhahiso, e se nang matla a fokolang. Kakaretso ea tlhahiso 6A max.
  Se ke oa feta litekanyetso tsa phepelo ea motlakase ka bomong.
  ACMS8CB:
• Liphetho tse sirelelitsoeng ke PTC li reiloe @ 2A ka tlhahiso, Sehlopha sa 2 se na le matla a fokolang. Kakaretso ea tlhahiso 6A max.
  Se ke oa feta litekanyetso tsa phepelo ea motlakase ka bomong.
• Liphetho tse robeli (8) tse laoloang ka boikemelo kapa tse robeli (8) tse laoloang ka boikemelo tsa Foromo ea "C" (sheba ka tlase bakeng sa lintlha):
  a) Fail-Sireletsehile le/kapa Fail-Sireletsehile matla a tsoang.
  b) Lipheelano tsa Foromo "C" li reiloe @ 2.5A. 12, 24VDC,
  0.6 Power Factor (ACMS8 feela).
  c) Lisebelisoa tsa motlakase tse thusang (tse sa fetoheng).
  d) Motsoako ofe kapa ofe oa tse ka holimo.
• Liphetho tsa motho ka mong li ka hlophisoa ho OFF boemo bakeng sa ts'ebeletso (output jumper set to the middle).
  Ha e sebetse lits'ebetsong tsa Dry Contact.
• E fe kapa e fe ho tse robeli (8) tse fehlang motlakase tse sirelelitsoeng ke PTC li ka khethoa hore li latele Input 1 kapa Input 2. The output voltage ea tlhahiso e 'ngoe le e 'ngoe e tšoana le matla a ho kenyatage ea tse kentsoeng.
• Khatello e phahameng.

Lintlha tsa Fuse/PTC:
eFlow104NB:

• Fuse e kenang e lekantsoe ho 6.3A/250V.
• Fuse ea betri e lekantsoe 15A/32V.
  ACMS8:
• Fuse ea mantlha e kentsoeng e lekantsoe 15A/32V.
• Li-fuse tse hlahisoang ke 3A/32V.
  ACMS8CB:
• Kenyelletso ea mantlha ea PTC e lekantsoe 9A.
• Li-PTC tse hlahisoang li fuoe lintlha tse 2A.

Boloka Battery (eFlow104NB):

• Chaja e hahelletsoeng ka hare bakeng sa asiti ea lead e tiisitsoeng kapa libeteri tsa mofuta oa gel.
• Boholo ba tefiso ea hajoale ke 1.54A.
• Jarolla ka ho iketsa ho ea stand-by betri ha AC hloleha.
  Matla a ho fetisetsoa ho betri e emeng e etsahala hang hang ha ho na tšitiso.

Tlhokomelo (eFlow104NB):

• AC e hloleha ho laola (ho theha mabitso a "C").
• Betri ha e sebetse le ho hlokomela boteng (foromo "C" mabitso).
• Ho tima matla a tlase. E koala li-terminals tsa DC haeba betri e le matlatage theoha ka tlase ho 71-73% bakeng sa li-unit tsa 12V le 70-75% bakeng sa li-unit tsa 24V (ho itšetlehile ka matla a matla). E thibela ho tsoa ha betri e tebileng.

Khaola Alarm ea Mollo:
eFlow104NB:

• Ho khaoha ha Alamo ea Mollo e hlokometsoeng (ho latching kapa ho se latching) 10K EOL resistor. E sebetsa ho trigger e tloahelehileng e bulehileng (NO) kapa ka tloaelo e koetsoeng (NC).

ACMS8(CB):

• Ho khaoha ha Alarm ea Mollo (ho latching kapa ho se lache) ho ka khethoa ka bonngoe bakeng sa liphetho tse robeli (8).
  Likhetho tsa ho kenya Alarm ea Mollo:
  a) Ka tloaelo bula [NO] kapa ka tloaelo e koetsoe [NC] e omileng ea ho kopanya. Kenyelletso ea ho khutlisa polarity ho tsoa ho potoloho ea matšoao a FACP.
• FACP input WET ke rated 5-30VDC 7mA.
• FACP input EOL e hloka 10K end-of-line resistor.
• FACP output relay [NC]:
  Ekaba Dry 1A / 28VDC, 0.6 Power Factor kapa
  Khanyetso ea 10K e nang le [EOL JMP] e tiile.

Matšoao a bonoang:
eFlow104NB:

• Tala ea AC LED: E bonts'a 120VAC e teng.
• Red DC LED: E supa tlhahiso ea DC.
  ACMS8(CB):
• Li-LED tse khubelu: Hlalosa hore liphetho li entsoe.
• LED e putsoa: E bonts'a hore ho hakolloa ha FACP ho qalile.
• Motho ka mong
  Moqtagle li-LED: Hlahisa 12VDC (Tala) kapa 24VDC (Khubelu).

Tikoloho:

• Mocheso o sebetsang: 0ºC ho isa ho 49ºC tikolohong.
• Mongobo: 20 ho isa ho 85%, e sa fokotseng.

Mekhahlelo ea Kakaretso (hoo e ka bang H x W x D):
15.5" x 12" x 4.5"
(393.7mm x 304.8mm x 114.3mm).

Litaelo tsa ho Kena:

Mekhoa ea likhoele e tla tsamaellana le Khoutu ea Naha ea Motlakase/NFPA 70/NFPA 72/ANSI, Khoutu ea Motlakase ea Canada, le likhoutu tsohle tsa lehae le ba boholong ba nang le matla a ho laola. Sehlahisoa se reretsoe ho sebelisoa ka tlung feela.

1. Beha yuniti sebakeng se lakatsehang. Tšoaea le ho phunya masoba leboteng ho tsamaisana le likoti tse peli tse ka holimo sebakeng se kampetsoeng. Kenya li-fasteners le li-screws tse peli leboteng 'me lihlooho tsa screw li hlahelle. Beha masoba a ka holimo a koaletsoeng holim'a likurufu tse peli tse ka holimo, boemo, 'me u sireletsehe. Tšoaea boemo ba likoti tse peli tse tlase. Tlosa sebaka se kampetsoeng. Hlakola likoti tse tlase ebe u kenya li-fasteners tse peli. Beha masoba a ka holimo a kokelo holim'a likurufu tse peli tse ka holimo. Kenya li-screw tse peli tse tlase 'me u netefatse hore u tiisa li-screw tsohle (Enclosure Dimensions, pg. 8). Sireletsa sebaka se kampetsoeng fatše.
2. Etsa bonnete ba hore li-jumpers tsohle tsa lihlahisoa [PWR1] - [PWR8] li behiloe sebakeng sa OFF (bohareng) (setšoantšo sa 1, leqephe la 3).
3. Hokela matla a AC a sa fetoheng (120VAC 60Hz) ho li-terminals tse tšoailoeng [L, N] li ka bonoa ka lense ea LED lemating la sebaka se kampetsoeng. Sebelisa 14 AWG kapa e kholoanyane bakeng sa likhokahano tsohle tsa matla. Sireletsehile terata e tala lebisa fatše fatše. Boloka likhoele tse lekanyelitsoeng matla li arohane le lithapo tse se nang matla (120VAC 60Hz Input, Battery Wires). Bonyane sebaka sa sebaka sa 0.25" se tlameha ho fanoa.
   TLHOKOMELO: U se ke ua tšoara likarolo tsa tšepe tse pepenene. Koala matla a potoloho ea lekala pele u kenya kapa u sebeletsa lisebelisoa. Ha ho na likarolo tse ka sebelisoang ke mosebelisi kahare.
   Fetisetsa ho kenya le ho fana ka litšebeletso ho basebeletsi ba nang le tsebo.
4. Beha sehlahisoa se seng le se seng [OUT1] - [OUT8] ho tsamaisa matla a tsoang ho Input 1 kapa 2 (setšoantšo sa 1, pg. 3).
   Hlokomela: Lekanya tlhahiso ea voltage pele o kopanya lisebelisoa. Sena se thusa ho qoba tšenyo e ka bang teng.
5. Tima motlakase pele o hokela lisebelisoa.
6. Likhetho tsa tlhahiso: eFlow104NKA8(D) e tla fana ka liphetho tse fihlang ho tse robeli (8) tsa matla a fetotsoeng kapa tse robeli (8) tse omeletseng tsa "C", kapa motsoako ofe kapa ofe oa matla a fetotsoeng le liphetho tsa "C", le tse robeli (8) tse sa fetoheng. matla a thusang.
   Phetoho ea Motlakase o Fetotsoeng: Hokela molaetsa o fosahetseng (–) oa sesebelisoa se tsamaisoang ho terminal e tšoailoeng [COM].
   • Bakeng sa ts'ebetso ea Fail-Safe, hokela "positive" (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NC].
   • Bakeng sa ts'ebetso e hlolehileng-Sireletsehile, hokela ho kenya (+) sesebediswa se tsamaisoang ho theminale e tšoailoeng [NO].
   Liphetho tsa foromo ea "C":
   Ha lihlahisoa tsa "C" li lakatseha, jumper e lumellanang (1-8) e tlameha ho behoa sebakeng sa OFF (setšoantšo sa 7, leqephe la 9). Ntle le moo, fuse e lumellanang ea tlhahiso (1-8) e ka tlosoa (eFlow104NKA8 feela).
   Hokela negative (–) ea phepelo ea motlakase ka kotloloho ho sesebelisoa sa ho notlela.
   Hokela positi (+) ea phepelo ea motlakase ho theminale e tšoailoeng [C].
   • Bakeng sa ts'ebetso ea Fail-Safe, hokela positi (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NC].
   • Bakeng sa ts'ebetso e hlolehileng-Sireletsehile, hokela positi (+) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [NO].
   Mabitso a omileng a rated @ 2.5A, 28VDC.
   Lisebelisoa tsa Matla a Thusang (tse sa fetoloang):
   Hokela molaetsa o nepahetseng (+) oa sesebelisoa se tsamaisoang ho theminale e tšoailoeng [C] le negative (–) ea sesebelisoa se tsamaisoang ho theminale e tšoailoeng [COM]. Sephetho se ka sebelisoa ho fana ka matla bakeng sa babali ba likarete, li-keypad, joalo-joalo.
7. Bulela matla a mantlha ka mor'a hore lisebelisoa tsohle li hoketsoe.
8. Likhetho tsa Input Trigger:
   Hlokomela: Haeba ho khaoha ha Alarm ea Mollo ho sa sebelisoe, hokela sehanyetsi sa 10K ohm ho litheminale tse tšoailoeng [GND le EOL], 'me u hokele jumper ho litheminale tse tšoailoeng [GND, RST].
   Ka tloaelo Bula (NO) Kenyo:
   Theeletso ya taolo ya selaete ya logic DIP e fetohela ho OFF bakeng sa [Fetosa 1-8] (setšoantšo sa 2, ka ho le letona). Hokela mehala ea hau ho litheminale tse tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Keletso e Tlwaelehileng (NC):
   Theeletso ya selaete ya taolo ya DIP fetohela ho ON bakeng sa [Fetosa 1-8] (Setšoantšo sa 2, ka ho le letona). Hokela mehala ea hau ho litheminale tse tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Bula Kenyelletso ea Sink ea Collector:
   Hokela sink e bulehileng ea pokello ea metsi ho theminale e tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Metsi (Moqtage) Tlhophiso ea Kenyeletso:
   Ho shebella ka hloko polarity, hokela voltage input trigger wires le 10K resistor e fanoeng ho li-terminals tse tšoailoeng [+ INP1 –] ho [+ INP8 –].
   Haeba o sebelisa voltage ho qala ho kenya - seta phetoho e lumellanang ea INP Logic sebakeng sa "OFF".
   Haeba ho tlosa voltage ho qala ho kenya - seta phetoho e lumellanang ea INP Logic ho boemo ba "ON".
9. Likhetho tsa Sehokelo sa Alarm ea Mollo:
   [NC] eo hangata e koetsoeng, eo hangata e bulang [NO] kapa keno ea ho khutlisa polarity ho tsoa ho potoloho ea matšoao ea FACP e tla hlahisa likhetho tse khethiloeng. Ho nolofalletsa FACP Disconnect bakeng sa tlhahiso, bulela switch e tsamaellanang ea DIP [SW1-SW8].
   Ho tima FACP hakoa bakeng sa tlhahiso, tima switch e tsamaellanang ea DIP [SW1-SW8] TIMA. Sesebelisoa se fumaneha ka ho toba ka letsohong le letšehali la Li-terminals tsa Fire Alarm Interface. Ka tloaelo Bula Kenyo:
   Kopanya relay ea hau ea FACP le sehanyetsi sa 10K ka 'moho ho litheminale tse tšoailoeng [GND] le [EOL].
   Kenyelletso e Tloaelehileng:
   Kopanya relay ea hau ea FACP le sehanyetsi sa 10K ho litheminale tse tšoailoeng [GND] le [EOL].
   Sehlomathisi sa Potoloho sa Potoloho sa Letshwao la FACP:
   Hokela positive (+) le negative (–) ho tloha ho FACP signaling circuit output ho litheminale tse tšoailoeng [+ FACP –]. Hokela FACP EOL ho li-terminals tse tšoailoeng [+ RET –] (polarity e hlalositsoe boemong ba alamo).
   Ho Khaola Alamo ea Mollo e sa Chesehang: Hokela jumper ho litheminale tse tšoailoeng [GND, RST].
   Ho Khaola Alamo ea Mollo: Hokela sesebelisoa sa ho seta botjha ha NO ka tlwaelo ho ditheminale tse ngotsweng [GND, RST].
10. FACP Dry NC tlhahiso:
    Hokela sesebediswa se lakatsehang se tla susumetswa ke yuniti e ommeng ya kgokahano ho ditheminale tse ngotsweng [NC] le [C].
    Ha [EOL JMP] e bolokiloe e tiile, tlhahiso ke ea 0 Ohm ho hanyetsa boemong bo tloaelehileng.
    Ha [EOL JMP] e koetsoe, khanyetso ea 10k e tla fetisetsoa sesebelisoa se latelang ha e le boemong bo tloaelehileng.
11. Lihokelo tsa Battery tse emeng (Setšoantšo sa 6, leqepheng la 8):
    Bakeng sa lits'ebetso tsa US Access Control li-betri lia ikhethela. Libetri lia hlokahala bakeng sa ho kenya lisebelisoa tsa Canada (ULC-S319). Ha libetri li sa sebelisoe, tahlehelo ea AC e tla fella ka tahlehelo ea matla a tlhahisotage.
    Ha tšebeliso ea libeteri tse emeng li lakatseha, e tlameha ho ba acid ea lead kapa mofuta oa gel.
    Kopanya betri ho li-terminals tse tšoailoeng [- BAT +] (Fig. 4g, pg. 6). Sebelisa libeteri tse peli (2) tsa 12VDC tse hokahaneng letotong bakeng sa ts'ebetso ea 24VDC (li-lead tsa betri li kenyelelitsoe). Sebelisa libeteri - li-betri tsa Castle CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) libeteri kapa libeteri tse amoheloang ke UL BAZR2 le BAZR8 tsa lintlha tse nepahetseng.
12. Liphetho tsa Battery le AC Supervision (Setšoantšo sa 4, leqephe la 8):
    Hoa hlokahala ho hokela lisebelisoa tsa bolaoli tse tlalehang mathata ho liphetho tse tšoailoeng [AC Fail, BAT Fail] le liphetho tsa phepelo ea bolaoli tse tšoailoeng [NC, C, NO] ho lisebelisoa tse loketseng tsa tsebiso ea pono.
    Sebelisa 22 AWG ho isa ho 18 AWG bakeng sa tlaleho ea AC Fail & Low/No Bettery.
13. Ho liehisa tlaleho ea AC ka lihora tse peli. beha sesebelisoa sa DIP [AC Delay] sebakeng sa OFF (Setšoantšo sa 2c, leqephe la 4).
    Ho liehisa tlaleho ea AC bakeng sa 1 min. beha DIP switjha [AC Delay] ho ON boemo (sa feiga. 4c, pg. 6).
14. Ho Khaola Alamo ea Mollo (Setšoantšo sa 4c, leqephe la 6):
    Ho bulela Mollo Ho Khaoha ha Alamo ea Mollo, seta switjha ea DIP [Shutdown] ho ea sebakeng sa ON.
    Ho tima Alamo ea Mollo Hakolla, seta switjha ea DIP [Shutdown] ho ea ho OFF.
15. Ho kenngoa ha tamper switch:
    Thaba ea UL Listed tamper switch (Altronix ea mohlala TS112 kapa e lekanang le eona) ka holimo ho sebaka se kampetsoeng. Tsamaisa tamper switjha bracket moeling oa sebaka se koaletsoeng hoo e ka bang 2 "ho tloha ka lehlakoreng le letona (setšoantšo sa 6a, leqephe la 8).
    Kopanya tamper switch wiring ho ea ho Access Control Panel kapa sesebelisoa se nepahetseng sa tlaleho se Lethathameng la UL. Ho kenya letshwao la alamo tshebetsong bula lemati la kampereho.

Wiring:

Sebelisa 18 AWG kapa ho feta bakeng sa matla a tlasetaglikhokahano tsa motlakase.
Hlokomela: Hlokomela ho boloka li-circuits tse fokolang matla li arohane le li-wiring tse se nang matla (120VAC, Battery).

Tlhokomelo:

Yuniti e lokela ho lekoa bonyane hang ka selemo bakeng sa ts'ebetso e nepahetseng ka tsela e latelang:
Khumo Voltage Teko: Tlas'a maemo a tloaelehileng a mojaro, molumo oa DC oa voltage lokela ho hlahlojwa bakeng sa vol e nepahetsengtage level eFlow104NB: 24VDC nominal rated @ 10A max.
Teko ea Battery: Tlas'a mojaro o tloaelehileng, maemo a lekola hore betri e tjhajiloe ka botlalo, hlahloba molumo o boletsoengtage (24VDC @ 26.4) ka bobeli boemelong ba betri le liteisheneng tsa boto tse tšoailoeng [- BAT +] ho netefatsa hore ha ho na ho khaoha lithapong tsa ho hokela betri.
Hlokomela: Nako e phahameng ea ho tjhaja ha e ntse e tsoa ke 1.54A.
Hlokomela: Bophelo ba betri bo lebeletsoeng ke lilemo tse 5, leha ho le joalo, ho kgothaletswa ho fetola libeteri ka lilemo tse 4 kapa ka tlase ha ho hlokahala.

Setšoantšo sa 4 - eFlow104N Tlhophiso ea Boto

Tlhokomeliso ea Trouble/Time Limited ea Libetri tse Emeng:
Bakeng sa ho latela ULC S318-96, potoloho ea Temoso ea Time Limited e tlameha ho hokeloa bakeng sa phatlalatso ea lehae kapa e hole ka Amber kapa Red LED ho bonts'a Mathata a DC (betri e tlase, tahlehelo ea betri kapa ha 95% ea betri e emeng e felile. fokotsehile). Hokela potoloho ho likhokahano tsa relay ea Batt Fail ho kenyelletso e nepahetseng ea UL Listed Burglar Alarm kapa Access Control Panel. Palo e latelang e bontša potoloho e hlokahalang bakeng sa phatlalatso ea sebaka seo.

Setšoantšo sa 5 - Letšoao la bothata ba betri
Bakeng sa tšebeliso ea Canada, e khubelu e bontšang lamp e tlameha ho bonahala ho tsoa bokantle ba sebaka sena se kampetsoeng.
Tsamaisa leoto le le leng la UL Lethathamong la mohloli oa matla a lekanyelitsoeng ho lamp.
Thala leoto la bobeli la mohloli oa matla ho e bontšang lamp ka letoto la lihlooho tse nang le li-terminals tsa ho kopana le betri li hlōleha ho tšoauoa [BAT FAIL - C, NO] (Setšoantšo sa 5, leqephe la 6).

Tlhahlobo ea LED:

eFlow104NB Phepelo ea Matla/Charger

Khubelu (DC)	Botala (AC/AC1)	Boemo ba Phepelo ea Matla
ON	ON	Boemo bo tloaelehileng ba ts'ebetso.
ON	TLOA	Tahlehelo ea AC. Betri ea standby e fana ka matla.
TLOA	ON	Ha ho tlhahiso ea DC.
TLOA	TLOA	Tahlehelo ea AC. Betri e emeng kapa e sa sebetseng. Ha ho tlhahiso ea DC.

ACMS8 le ACMS8CB Access Power Controller

LED	ON	TLOA
LED 1- LED 8 (Khubelu)	Li-relay li feletsoe ke matla.	Li-relay tse hlahisoang li matlafalitsoe.
SEFAHLEHO	Ho kenya FACP (boemo ba alamo).	FACP e tloaelehileng (boemo boo e seng alamo).
Sephetho se Setala 1-8	12VDC	—
Sephetho se Sefubelu 1-8	24VDC	—

Boitsebahatso Terminal:
eFlow104NB Phepelo ea Matla/Charger

Terminal Taba	Mosebetsi/Tlhaloso
L, N	Hokela 120VAC 60Hz ho li-terminals tsena: L ho chesa, N ho se nke lehlakore (e se nang matla a fokolang) (Setšoantšo sa 4a, leqephe la 6).
- DC +	24VDC nominal @ 10A tlhahiso e tsoelang pele (sehlahisoa se se nang matla a fokolang) (Setšoantšo sa 417, pg. 6).
Hlahisa EOL e Laolehileng	Sebopeho sa Alarm ea Mollo se kenya letsoho ho tsoa ho nako e khuts'oane kapa FACP. Lisebelisoa tsa trigger li ka 'na tsa buleha' me ka tloaelo li koaloa ho tloha ho FACP output circuit (motlakase o fokolang matla) (Fig. 4d, pg. 6).
CHE, GND RESET	FACP segokanyimmediamentsi sa sebolokigolo latching kapa bao e seng latching (matla a lekanyelitsoeng) (Fig. 4e, pg. 6).
+ AUX -	Motlatsi oa Sehlopha sa 2 se hlahisoang ke matla a fokolang a lekantsoeng @ 1 A (e sa fetoheng) (Setšoantšo sa 41, leqephe la 6).
AC Fail NC, C, NO	E bontsha tahlehelo ya matla a AC, mohlala, hokela sesebedisweng se utlwahalang kapa phanele ya alamo. Hangata relay e matlafatsoa ha matla a AC a le teng. Tekanyetso ea ho ikopanya 1A @ 30VDC (matla a fokolang) (setšoantšo sa 4b, leqephe la 6).
Bat Fail NC, C, NO	E bontsha boemo ba betri e tlase, mohlala, hokela phanele ya alamo. Hangata relay e matlafatsoa ha matla a DC a le teng. Boemo ba ho ikopanya le 1A @ 30VDC. Betri e tlositsoeng e tlalehoa nakong ea metsotso e 5. Ho tsosolosoa ha betri ho tlalehoa ka hare ho motsotso oa 1 (matla a fokolang) (Setšoantšo sa 4b, pg. 6).
- BAT +	Lihokelo tsa betri tse emeng. Tefiso e phahameng ea hona joale 1.54A (e se nang matla a fokolang) (setšoantšo sa 4g, leqephe la 6).

ACMS8 le ACMS8CB Access Power Controller

Terminal Taba	Mosebetsi/Tlhaloso
+ PWR1 -	Feme e hokahantsoeng le eFlow104NB. Se ke oa sebelisa li-terminals tsena.
+ PWR2 -	Feme e hokahantsoeng le VR6 voltage regulator. Se ke oa sebelisa li-terminals tsena.
+ INP1 - ka + INP8 -	Tse robeli (8) tse laoloang ka boikemelo Normally Open (NO), Ka tloaelo Ho Koetsoe (NC), Open Collector Sink kapa Wet Input Triggers.
C, NC	FACP Dry NC output rated 1A/28VDC © 0.6 Power Factor. Sehlopha sa 2 se na le matla a fokolang. Ka EOL JMP e tiile, e tla fana ka khanyetso ea 10k maemong a tloaelehileng.
GND, RST	FACP segokanyimmediamentsi sa sebolokigolo latching kapa e seng latching. HA HO se kentsoeng se ommeng. Sehlopha sa 2 se na le matla a fokolang. E tla khutsufatsoa bakeng sa sebopeho sa FACP se sa ts'oanelang kapa Latch FACP reset.
GND, EOL	EOL E hlokometseng liteishene tsa ho Kena tsa FACP bakeng sa ts'ebetso ea polarity ea ho khutlisa FACP. Sehlopha sa 2 se na le matla a fokolang.
- F, + F, - R, + R	FACP Signaling Circuit Input and Return terminals. Sehlopha sa 2 se na le matla a fokolang.
Tlhahiso ea 1 ho ea ho Output 8 NO C, NC, COM	Liphetho tse robeli (8) tse laoloang ka boikemelo [Fail-Safe (NC) kapa Fail-Secure (NO)] le tse robeli (8) tse laoloang ka boikemelo tsa Foromo ea "C" Relay.

Setšoantšo sa 6 - eFlow104NKA8(D)

Ka boikhethelo Battery e Emang ka Bohato e Hlahang bakeng sa Lits'ebetso tsa UL294 Hlokomela: Libetri tsa 12V lia hlokahala bakeng sa Lisebelisoa tsa ULC-S319.

Ka boikhethelo Battery e Emang ka Bohato e Hlahang bakeng sa Lits'ebetso tsa UL294 Hlokomela: Libetri tsa 12V lia hlokahala bakeng sa Lisebelisoa tsa ULC-S319.

TLHOKOMELO: Sebelisa libeteri tse emeng tse peli (2) 12VDC.
Boloka lithapo tse lekanyelitsoeng matla li arohane le tse se nang matla.
Sebelisa sebaka sa bonyane sa 0.25”.
12AH Libetri tse ka chachang hape ke libeteri tse kholo ka ho fetisisa tse ka kenang ka har'a sebaka sena se kampetsoeng.
Sebaka sa betri sa kantle se thathamisitsoeng ka UL se tlameha ho sebelisoa ha ho sebelisoa libeteri tsa 40AH kapa 65AH.

Setšoantšo se Tloaelehileng sa Tšebeliso:

Setšoantšo sa 7

Litšoantšo tsa Hook-Up:

Setšoantšo sa 8 - Daisy-chaining unit e le 'ngoe kapa ho feta ACMS8(CB).
EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. E sa Lateng.

Setšoantšo sa 9 - Daisy-chaining unit e le 'ngoe kapa ho feta ACMS8(CB).
EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. Latching Single Reset.

Setšoantšo sa 10 - Daisy e kopanya lihlopha tse le 'ngoe kapa tse ngata tsa ACMS8(CB).
EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. Latching Individual Reset.

Litšoantšo tsa Hook-Up:

Setšoantšo sa 11 - Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo). E sa Lateng.	Setšoantšo sa 12 - Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo). Latching.
Setšoantšo sa 13 - Hangata ho koetsoe ho kenya letsoho (Non-Latching).	Setšoantšo sa 14 - Ka tloaelo ho Koetsoe ho kenya letsoho (Latching).
Setšoantšo sa 15 - Ka tloaelo Open trigger input (Non-Latching).	Setšoantšo sa 16 - Ka tloaelo Open trigger input (Latching).

Mekhahlelo ea Kakaretso (BC400):
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix ha e ikarabelle bakeng sa liphoso leha e le life tsa typographical.
140 58th Street, Brooklyn, New York 11220 USA | mohala: 718-567-8181 | fax: 718-567-9056
websebaka: www.altelengx.com | lengolo-tsoibila: info@altronix.com | Warranty ea bophelo bohle
IIeFlow104NKA8(D)
G29U

Litokomane / Lisebelisoa

Altronix eFlow104NA8 Series Dual Output Access Power Controllers [pdf] Tlhophiso Tataiso eFlow104NA8 Series Dual Output Access Power Controllers, eFlow104NA8 Series, Dual Output Access Power Controllers, Access Power Controllers, Power Controllers, Controllers

Litšupiso

• Bukana ea Mosebelisi