Altronix eFlow104NA8 Series Dual Output Access Power Controllers Installation Guide

eFlow104NA8 Series Dual Output
Svika Power Controllers
Installation Guide

Zviri mukati hide

1 eFlow104NA8 Series Dual Output Access Power Controllers

2 Overview:

3 Zvinodiwa:

4 Installation Instruction:

5 Maintenance:

6 Yakajairika Yekushandisa Dhiyagiramu:

7 Hook-Up Diagrams:

8 Zvinyorwa / Zvishandiso

8.1 References

9 Related Posts

eFlow104NA8 Series Dual Output Access Power Controllers

eFlow104NKA8

12VDC kana 5VDC inosvika 6A uye/kana 24VDC inosvika 10A (240W yakazara simba) inosarudzwa nekubuda.

Zvisere (8) zvefuse-protected.
Masere (8) anosarudzwa Fail Safe, Fail-Secure, kana Form “C” dry outputs

Moto Alarm Dimbura inosarudzwa nekubuda
Yakavakirwa-mukati Charger yeakavharirwa lead acid kana gel-mhando mabhatiri

eFlow104NKA8D

12VDC kana 5VDC inosvika 6A uye/kana 24VDC inosvika 10A (240W yakazara simba) inosarudzwa nekubuda.

Eight (8) Kirasi 2 simba-shoma PTC-yakachengetedzwa zvinobuda.
Masere (8) anosarudzwa Fail Safe, Fail-Secure, kana Form “C” dry outputs.

Fire Alarm Disconnect inosarudzwa nekubuda.
Yakavakirwa-mukati Charger yeakavharirwa lead acid kana gel-mhando mabhatiri.

Rev. eFlow104NKA8-072220

Kuisa Kambani: _______________ Service Rep. Zita: ___________________________________
Kero: _____________________________________________ Nharembozha: ______________________________

Overview:

Altronix eFlow104NKA8 uye eFlow104NKA8D govera uye shandura simba kuti uwane masystem ekudzora uye zvishongedzo. Ivo vanoshandura 120VAC 60Hz yekupinda kuita sere (8) yakazvimirira inodzorwa 12VDC kana 24VDC yakachengetedzwa inobuda. Access Power Controller's mbiri yekupinza dhizaini inobvumira simba kutungamirwa kubva maviri (2) fekitori-yakamisikidzwa yakazvimirira yakaderera vol.tage 12 kana 24VDC Altronix magetsi ekupa kune masere (8) akazvimirira anodzora fuse (eFlow104NKA8) kana PTC (eFlow104NKA8D) akachengetedzwa zvabuda. Simba rinobuda rinogona kushandurwa kuita yakaoma-fomu "C" mazita. Mabudiro anoitwa neakavhurika muunganidzi sink, anowanzo kuvhurika (NO), anowanzo kuvharwa (NC) yakaoma trigger yekupinda, kana nyoro inobuda kubva kune Access Control System, Kadhi Reader, Keypad, Push Bhatani, PIR, nezvimwe. eFlow104NKA8(D) ichaita simba renzira kune zvakasiyana-siyana zvekupinda kutonga hardware zvishandiso zvinosanganisira Mag Locks, Electric Strikes, Magnetic Door Holders, etc. Outputs ichashanda mune zvose Fail-Safe uye / kana Fail-Secure modes. Iyo FACP Interface inogonesa Emergency Egress, uye Alarm Monitoring, kana inogona kushandiswa kumutsa mimwe michina yekubatsira. Iyo yemoto alarm yekubvisa ficha inosarudzwa yega kune chero kana ese masere (8) zvinobuda. Iyo spade yekubatanidza inokutendera iwe kuti daisy cheni simba kune akawanda ACMS8(CB) modules. Iyi ficha inobvumidza iwe kugovera simba pamusoro pezvakawanda zvinobuda kune makuru masisitimu.

Stand-by Specifications:

Bhatiri	Burg. Applications 4 hr. Mira ne/ 15 min. Alarm	Fire Applications 24 hr. Mira ne/ 5 min. Alarm	Access Control Applications Mira ne
7AH	0.4A/10A	N/A	5 mins./10A
12A11	1A/10A	0.3A/10A	15 mins./10A
40A11	6A/10A	1.2A/10A	Kupfuura 2 Maawa/10A
65A11	6A/10A	1.5A/10A	Kupfuura 4 Maawa/10A

Zvinodiwa:

Zvinopinza
eFlow104NB:

120VAC, 60Hz, 4.5A.
ACMS8/ACMS8CB:

Zvisere (8) zvinokonzeresa:
a) Kazhinji yakavhurika (NO) mapeji (akaoma macontacts).
b) Kazhinji yakavharwa (NC) mapeji (akaoma contacts).
c) Vhura zvekuunganidza sink.
d) Wet Input (5VDC - 24VDC) ine 10K resistor
e) Chero musanganiswa wezviri pamusoro.

Zvinobuda:
Simba:

12VDC kana 5VDC kusvika 6A, 24VDC kusvika 10A
(240W simba rose).
Yekubatsira Kirasi 2 simba-rinogumira kubuda
rated @ 1A (isina kuchinjika).

Kupfuuratage kudzivirirwa.
ACMS8:
Fuse-yakadzivirirwa inobuda yakayerwa @ 2.5A painobuda, isina-simba-inogumira. Zvose zvinobuda 6A max.
Usapfuure chiyero chemagetsi ega ega.
ACMS8CB:

PTC-yakadzivirirwa inobuda yakatemerwa @ 2A pane inobuda, Kirasi 2 simba-shoma. Zvose zvinobuda 6A max.
Usapfuure chiyero chemagetsi ega ega.
Zvisere (8) zvinosarudzwa zvakazvimiririra zvinodzorwa zvinobuda kana zvisere (8) zvakazvimiririra zvakadzora Fomu "C" relay zvabuda (ona pazasi kuti uwane ratings):
a) Kutadza-Kuchengeteka uye/kana Kutadza-Kuchengetedza magetsi kubuda.
b) Fomu "C" relays yakarongwa @ 2.5A. 12, 24VDC,
0.6 Power Factor (ACMS8 chete).
c) Magetsi ekuwedzera emagetsi (asina kuchinjika).
d) Chero musanganiswa wezviri pamusoro.

Yega inobuda inogona kusetwa kune OFF chinzvimbo chesevhisi (output jumper yakaiswa kune yepakati chinzvimbo).
Haishande kune Dry Contact application.
Chero pane masere (8) fuse/PTC-akadzivirirwa magetsi anobuda anosarudzwa kutevera simba Input 1 kana Input 2. Mhepo inobudatage yega yega inobuda yakafanana neyekuisa voltage yezvakasarudzwa.

Surge kudzvinyirira.

Fuse/PTC Ratings:
eFlow104NB:

Iyo fiyuzi yekupinza yakaiswa pa6.3A/250V.
Battery fuse inonzi 15A/32V.
ACMS8:
Iyo huru yekuisa fuse yakarongwa 15A/32V.
Mafiyuzi anobuda akatemerwa 3A/32V.
ACMS8CB:
Iyo huru yekuisa PTC yakarongwa 9A.
Kubuda kwePTCs kwakarongwa 2A.

Backup yebhatiri (eFlow104NB):

Yakavakirwa-mukati charger yeakavharirwa lead acid kana gel-mhando mabhatiri.
Maximum charge ikozvino 1.54A.
Chinja otomatiki kune bhatiri rakamira kana AC yatadza.
Kuendesa kune yakamira-nebhatiri simba rinobva ipapo pasina kukanganisa.

Kutarisira (eFlow104NB):

AC inotadza kutarisa (fomu "C" mazita).
Bhatiri rakundikana & kutarisa kuvapo (fomu "C" mazita).
Kudzima kwemagetsi mashoma. Inodzima DC inobuda zviteshi kana bhatiri voltage inodonha pazasi 71-73% ye12V mayunitsi uye 70-75% ye24V mayunitsi (zvichienderana nemagetsi). Inodzivirira kubuda kwebhatiri rakadzika.

Moto Alarm Dimbura:
eFlow104NB:

Inotariswa Moto Alarm bvisa (latching kana isina-latching) 10K EOL resistor. Inoshanda pane inowanzovhurika (NO) kana inowanzovharwa (NC) trigger.

ACMS8(CB):

Moto Alarm disconnect (latching kana kusa-latching) inosarurwa yega kune chero kana ese ezvisere (8) zvinobuda.
Moto Alarm bvisa sarudzo dzekuisa:
a) Kazhinji kuvhura [NO] kana kazhinji kuvharwa [NC] yakaoma yekubatanidza yekupinda. Polarity reversal input kubva kuFACP signing circuit.
FACP yekupinda WET yakayerwa 5-30VDC 7mA.
FACP yekuisa EOL inoda 10K yekupedzisira-ye-mutsara resistor.

FACP inoburitsa relay [NC]:
Pamwe Dry 1A/28VDC, 0.6 Power Factor kana
10K kuramba ne [EOL JMP] yakasimba.

Visual Indicators:
eFlow104NB:

Green AC LED: Inoratidza 120VAC iripo.

Red DC LED: Inoratidza DC kubuda.
ACMS8(CB):
Red LEDs: Ratidza zvinobuda zviri kukonzeresa.
Bhuruu LED: Inoratidza kuti FACP disconnect yatanga.

Individual
Voltage LEDs: Ratidza 12VDC (Green) kana 24VDC (Dzvuku).

Environmental:

Kushanda tembiricha: 0ºC kusvika 49ºC ambient.

Humidity: 20 kusvika 85%, isina-condensing.

Enclosure Dimensions (inenge H x W x D):
15.5" x 12" x 4.5"
(393.7mm x 304.8mm x 114.3mm).

Installation Instruction:

Wiring nzira dzichaenderana neNational Electrical Code/NFPA 70/NFPA 72/ANSI, Canadian Electrical Code, uye nemakodhi ese enzvimbo nezviremera zvine masimba. Chigadzirwa chacho chakagadzirirwa kushandiswa kwemukati chete.

Isa iyo unit munzvimbo yaunoda. Maka uye gadzira maburi mumadziro kuti uenderane nepamusoro makiyi maburi ari mukati mekuvharirwa. Isa zvisungo zviviri zvekumusoro nema screws mumadziro ane sikuruwa misoro yakabuda. Isa makiyi epamusoro evhavha pamusoro pemasikiru maviri epamusoro, nhanho, uye chengetedza. Maka nzvimbo yemaburi maviri ezasi. Bvisa yakavharirwa. Dhobora maburi ezasi uye isa ma fasteners maviri. Isa makiyi epamusoro echivharo pamusoro pemakona maviri epamusoro. Isai maviri ezasi screws uye ita shuwa kuomesa ese screws (Enclosure Dimensions, pg. 8). Chengetedza yakavharirwa pasi pasi.
Ita shuwa kuti zvese zvinobuda zvinosvetuka [PWR1] - [PWR8] yakaiswa mu OFF (pakati) chinzvimbo (Fig. 1, pg. 3).
Batanidza isina kuchinjika AC simba (120VAC 60Hz) kune materminal akamakwa [L, N] anogona kuvonekwa kuburikidza neLED lens pamusuwo wezvakavharirwa. Shandisa 14 AWG kana yakakura kune ese magetsi ekubatanidza. Waya yakasvibira yakachengeteka inotungamira pasi pevhu. Chengetedza wiring ine simba-inogumira yakaparadzana kubva kune isina-simba-inogumira wiring (120VAC 60Hz Input, Battery Wire). Minimum 0.25” nzvimbo inofanira kupihwa.
KUCHENJERA: Usabata nhengo dzesimbi dzakafumurwa. Vhara simba redunhu rebazi usati waisa kana kusevha midziyo. Iko hakuna zvikamu zvinoshandisika mushandisi mukati.
Revera kuisirwa uye sevhisi kune vanokwanisa sevhisi vashandi.

Isa imwe neimwe inobuda [OUT1] - [OUT8] kunzira simba kubva Input 1 kana 2 (Fig. 1, pg. 3).
Cherechedza: Kuyera kubuda voltage pamberi pekubatanidza zvishandiso. Izvi zvinobatsira kudzivisa kukanganisa kunogona kuitika.
Dzima simba usati wabatanidza zvishandiso.
Sarudzo dzezvinobuda: eFlow104NKA8(D) ichapa anosvika masere (8) machinjiro emagetsi kana masere (8) yakaoma fomu "C" kubuda, kana chero musanganiswa wezvose zviri zviviri switched simba uye fomu "C" zvinobuda, pamwe masere (8) asina kuchinjika. ebetsero simba kubuda.
Yakachinja Magetsi emagetsi: Batanidza iyo isina kunaka (-) yekuisa yemudziyo uri kufambiswa kune terminal yakanyorwa [COM].
• Pakushanda kwaFail-Safe batanidza zvinonaka (+) zvemudziyo uri kufambiswa kuterminal yakanyorwa kuti [NC].
• PaKutadza-Kuchengetedza batanidza iyo yakanaka (+) inopinza yemudziyo uri kufambiswa kuterminal yakanyorwa kuti [NO].
Fomu "C" zvabuda:
Kana mafomu e "C" achidiwa, jumper inoenderana (1-8) inofanira kuiswa munzvimbo ye OFF (Fig. 7, pg. 9). Neimwe nzira, iyo inoenderana inobuda fuse (1-8) inogona kubviswa (eFlow104NKA8 chete).
Batanidza iyo isina kunaka (-) yemagetsi ekupa zvakananga kune yekukiya mudziyo.
Batanidza iyo yakanaka (+) yemagetsi emagetsi kune terminal yakanyorwa [C].
• Pakushanda kwaFail-Safe batanidza yakanaka (+) yemudziyo uri kufambiswa kuterminal yakanyorwa kuti [NC].
• PaKutadza-Kuchengetedza batanidza iyo yakanaka (+) yemudziyo uri kufambiswa kuterminal yakanyorwa kuti [NO].
Dry contacts rated @ 2.5A, 28VDC.
Ebetsero Simba rinobuda (isina kuchinjika):
Batanidza chakanaka (+) chinopinza chemudziyo uri kufambiswa kuterminal yakamaka [C] uye negative (-) yemudziyo uri kufambiswa kuterminal yamaka [COM]. Kubuda kunogona kushandiswa kupa simba kune vaverengi vemakadhi, keypads, nezvimwe.

Batidza simba guru mushure mekunge zvishandiso zvese zvabatanidzwa.
Input Trigger sarudzo:
Cherechedza: Kana Fire Alarm ikadimburwa ikasashandiswa, batanidza 10K ohm resistor kune materminals akaiswa [GND neEOL], uye batanidza jumper kumaterminal akaiswa [GND, RST].
Kazhinji Vhura (NO) Input:
Sraidhi yekupinda kudzora mantiki DIP chinja ichiisa OFF chinzvimbo che[Chinja 1-8] (Mufananidzo 2, kurudyi). Batanidza waya dzako kumaterminals akamakwa [+ INP1 –] ku [+ INP8 –].
Kazhinji Yakavharwa (NC) Inopinza:
Sraidhi yekupinda kudzora logic DIP chinja kupinda ON chinzvimbo che [Chinja 1-8] (Mufananidzo 2, kurudyi). Batanidza waya dzako kumaterminals akamakwa [+ INP1 –] ku [+ INP8 –].
Vhura Collector Sink Input:
Batanidza yakavhurika yekunyura sink yekuisa kune terminal yakanyorwa [+ INP1 -] ku [+ INP8 -].
Mvura (Voltage) Input Configuration:
Kunyatsocherechedza polarity, batanidza voltage input trigger waya uye yakapihwa 10K resistor kumaterminals akaiswa [+ INP1 –] ku [+ INP8 –].
Kana kushandisa voltage kukonzeresa kupinza - isa inoenderana INP Logic switch kune iyo "OFF" chinzvimbo.
Kana kubvisa voltage kukonzeresa kupinza - isa inoenderana INP Logic switch kune iyo "ON" chinzvimbo.
Fire Alarm Interface sarudzo:
Iyo inowanzovharwa [NC], inowanzovhura [NO] yekupinda kana polarity reversal input kubva kuFACP siginacha wedunhu inokonzeresa zvakasarudzwa. Kuti ugone kugonesa FACP Dimbura kune chinobuda batidza switch yeDIP inoenderana [SW1-SW8] KUBATSIRA.
Kudzima FACP disconnect yezvinobuda dzima DIP switch inoenderana [SW1-SW8] DZIMA. Iyo switch inowanikwa yakananga kuruboshwe kweMoto Alarm Interface Terminals. Kazhinji Open Input:
Waya yako FACP relay uye 10K resistor in parallel pamaterminals akaiswa [GND] uye [EOL].
Kazhinji Yakavharwa Inopinza:
Waya yako FACP relay uye 10K resistor munhevedzano pamaterminal akanyorwa [GND] uye [EOL].
FACP Inoratidza Circuit Input Trigger:
Batanidza yakanaka (+) uye yakaipa (-) kubva paFACP inosaina dunhu rinobuda kune materminal akanyorwa [+ FACP -]. Batanidza iyo FACP EOL kune materminal akamakwa [+ RET –] (polarity inoratidzwa mune aramu mamiriro).
Alarm Yemoto Isingabatike Inobvisa: Batanidza jumper kumaterminal akanyorwa [GND, RST].
Latching Fire Alarm Dimbura: Batanidza NO anowanzo vhura reset switch kumaterminal akanyorwa [GND, RST].

FACP Dry NC yakabuda:
Batanidza mudziyo waunoda kuti ukonzereswe neiyo unit yakaoma yekubatanidza inobuda kune materminal akaiswa [NC] uye [C].
Kana [EOL JMP] ichichengetwa yakasimba, inobuda ndeye 0 Ohm kuramba mune yakajairika mamiriro.
Kana [EOL JMP] yakadimburwa, 10k kuramba inopfuudzwa kune chinotevera chishandiso kana chiri mumamiriro ezvinhu.
Stand-by Battery Connections (Mufananidzo 6, peji 8):
Kune iyo US Access Control application mabhatiri anosarudzika. Mabhatiri anodiwa pakuisirwa kweCanada (ULC-S319). Kana mabhatiri akasashandiswa, kurasikirwa kwe AC kunozokonzera kurasikirwa kwekubuda kwevoltage.
Kana kushandiswa kwema-stand-by mabhatiri kunodiwa, anofanira kunge ari lead acid kana gel rudzi.
Batanidza bhatiri kumaterminals akaiswa [- BAT +] (Fig. 4g, pg. 6). Shandisa maviri (2) 12VDC mabhatiri akabatanidzwa munhevedzano ye24VDC oparesheni (yebhatiri inotungamira inosanganisirwa). Shandisa mabhatiri – Castle CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) mabhatiri kana UL anozivikanwa BAZR2 neBAZR8 mabhatiri echiyero chakakodzera.
Bhatiri uye AC Supervision zvabuda (Fig. 4, peji 8):
Zvinodiwa kuti ubatanidze midziyo yekuzivisa dambudziko kune zvakabuda zvakanyorwa [AC Fail, BAT Fail] uye supervisory relay zvinobuda zvakanyorwa [NC, C, NO] kumidziyo yekuzivisa yekuona yakakodzera.
Shandisa 22 AWG kusvika 18 AWG yeAC Fail & Low/No Battery reporting.

Kunonotsa AC kushuma kwemaawa maviri. isa iyo DIP switch [AC Kunonoka] kune OFF chinzvimbo (Fig. 2c, pg. 4).
Kunonotsa AC kushuma kwe1 min. isa DIP chinja [AC Kunonoka] kune ON chinzvimbo (Fig. 4c, pg. 6).
Moto Alarm Dimbura (Mufananidzo 4c, peji 6):
Kugonesa Fire Alarm Disconnect isa switch yeDIP [Shutdown] kune ON chinzvimbo.
Kudzima Fire Alarm Disconnect isa switch yeDIP [Shutdown] kune OFF chinzvimbo.
Kuiswa kwe tamper switch:
Mount UL Yakanyorwa tamper switch (Altronix modhi TS112 kana yakaenzana) pamusoro peiyo yakavharirwa. Svetera iyo tamper switch bracket kumucheto kweiyo yakavharirwa inenge 2" kubva kurudyi (Fig. 6a, pg. 8).
Batanidza tamper chinja wiring kune Access Control Panel yekupinda kana yakakodzera UL Yakanyorwa yekurekodha mudziyo. Kuti uvhure mucherechedzo wearamu vhura gonhi renzvimbo yakavharirwa.

Wiring:

Shandisa 18 AWG kana yakakura kune ese akaderera-voltage power connections.
Cherechedza: Chenjerera kuchengetedza masimba-ane mashoma maseketi akaparadzana neasina-simba-akaganhurwa wiring (120VAC, Battery).

Maintenance:

Iyo unit inofanirwa kuyedzwa kamwechete pagore kuti ishande kwakaringana sezvinotevera:
Kubuditsa Voltage Muedzo: Pasi pemamiriro akajairwa ekuremerwa, iyo DC inobuda voltage inofanirwa kuongororwa kuti ine voltage level eFlow104NB: 24VDC nominal rated @ 10A max.
Bhatiri Muedzo: Pasi peyakajairika mutoro, mamiriro tarisa kuti bhatiri rakazara, tarisa yakataurwa voltage (24VDC @ 26.4) pachiteshi chebhatiri nepamabhodhi akaiswa chiratidzo [- BAT +] kuti ive nechokwadi chekuti hapana kuputsika-mutambo dzekubatanidza bhatiri.
Cherechedza: Maximum kuchaja ikozvino pasi pezvinobuda ndeye 1.54A.
Cherechedza: Inotarisirwa hupenyu hwebheteri makore 5, zvisinei, zvinokurudzirwa kuchinja mabhatiri mumakore 4 kana pasi kana zvichidiwa.

Mufananidzo 4 - eFlow104N Board Configuration

Dambudziko/Nguva Yakaganhurirwa Yambiro yeMabhatiri Akamira:
Kuti utevedzere ULC S318-96, iyo Time Limited Yambiro dunhu rinofanirwa kunge rakabatana kune yemuno kana kure kure neAmber kana Red LED kuratidza DC Dambudziko (yakaderera bhatiri, kurasikirwa kwebhatiri kana 95% yebhatiri rakamira rave. depleted). Batanidza dunhu kune Batt Fail relay mameseji kune yakakodzera kupinza yeUL Yakanyorwa Burglar Alarm kana Access Control Panel. Mufananidzo unotevera unoratidza kutenderera kunodiwa pakuzivisa kwenzvimbo.

Fig. 5 - Battery dambudziko chiratidzo
Kushandiswa kweCanada, tsvuku inoratidza lamp inofanira kuonekwa kubva kunze kweichi chivharo.
Waya gumbo rimwe reUL Yakanyorwa, ine simba-shoma simba sosi kune inoratidza lamp.
Waya gumbo rechipiri resimba remagetsi kune rinoratidza lamp munhevedzano ine bhatiri inotadza relay contact terminals yakanyorwa [BAT FAIL - C, NO] (Fig. 5, pg. 6).

LED Diagnostics:

eFlow104NB Power Supply/Charger

Tsvuku (DC)	Green (AC/AC1)	Power Supply Status
ON	ON	Yakajairika mamiriro ekushanda.
ON	DZIMA	Kurasika kweAC. Bhatiri rekumira riri kupa simba.
DZIMA	ON	Hapana DC inobuda.
DZIMA	DZIMA	Kurasika kweAC. Radzimwa kana kushaya bhatiri rakamira. Hapana DC inobuda.

ACMS8 uye ACMS8CB Access Power Controller

LED	ON	DZIMA
LED 1- LED 8 (Dzvuku)	Output relay(s) de-energized.	Output relay(s) simba.
FACE	FACP inopinza yakakonzeresa (alarm mamiriro).	FACP yakajairika (isina-alarm mamiriro).
Green Output 1-8	12VDC	—
Red Output 1-8	24VDC	—

Terminal Identification:
eFlow104NB Power Supply/Charger

Terminal Legend	Basa/ Tsanangudzo
L, N	Batanidza 120VAC 60Hz kune aya materminals: L kusvika kupisa, N kune kwaakarerekera (asina-simba-shoma) (Fig. 4a, pg. 6).
-DC +	24VDC nominal @ 10A inoenderera mberi kubuda (isina simba-inogumira kubuda) (Fig. 417, pg. 6).
Trigger EOL Inotariswa	Fire Alarm Interface inokonzeresa kupinza kubva kupfupi kana FACP. Trigger inputs inogona kuvhurika uye kazhinji yakavharwa kubva kuFACP inobuda dunhu (simba-shoma yekupinda) (Fig. 4d, pg. 6).
KWETE, GND RESET	FACP interface latching kana kwete-latching (simba-shoma) (Fig. 4e, pg. 6).
+ AUX -	Mubatsiri Kirasi 2 simba-rinogumira kuburitsa rated @ 1 A (isina kuchinjika) (Fig. 41, pg. 6).
AC Fail NC, C, NO	Inoratidza kurasikirwa kwesimba reAC, semuenzaniso batanidza kune chinonzwika mudziyo kana alarm panel. Iyo relay inowanzo kupihwa simba kana AC simba riripo. Kubata chiyero 1A @ 30VDC (simba-shoma) (Fig. 4b, pg. 6).
Bat Fail NC, C, NO	Inotaridza kuderera kwebhatiri, semuenzaniso batanidza kune alarm panel. Iyo relay inowanzo kupihwa simba kana DC simba iripo. Kubata chiyero 1A @ 30VDC. Bhatiri rakabviswa rinoshumwa mukati memaminitsi mashanu. Battery rekubatanidza inoshumwa mukati meminiti 1 (simba-shoma) (Fig. 4b, pg. 6).
- BAT +	Kubatana kwebhatiri. Maximum charge ikozvino 1.54A (isina-simba-shoma) (Fig. 4g, pg. 6).

ACMS8 uye ACMS8CB Access Power Controller

Terminal Legend	Basa/ Tsanangudzo
+ PWR1 -	Fekitari yakabatana ne eFlow104NB. Usashandise materminals aya.
+ PWR2 -	Fekitari yakabatana neVR6 voltage regulator. Usashandise materminals aya.
+ INP1 - kuburikidza + INP8 -	Masere (8) anodzorwa akazvimirira Kazhinji Kuvhurika (NO), Kazhinji Kuvharwa (NC), Vhura Muunganidzi Sink kana Wet Input Triggers.
C, NC	FACP Dry NC yakabuda yakarongwa 1A/28VDC © 0.6 Power Factor. Kirasi 2 simba-shoma. Iine EOL JMP yakasimba, ichapa 10k kuramba mune yakajairika mamiriro.
GND, RST	FACP interface yatching kana kusa-latching. HAPANA yakaoma kuisa. Kirasi 2 simba-shoma. Kupfupikiswa kune isiri-latching FACP interface kana Latch FACP reset.
GND, EOL	EOL Inotariswa FACP Input zviteshi zve polarity reversal FACP basa. Kirasi 2 simba-shoma.
- F, + F, - R, + R	FACP Signaling Circuit Input uye Return terminals. Kirasi 2 simba-shoma.
Kuburitsa 1 kuburikidza neKubuda 8 HAPANA C, NC, COM	Zvisere (8) zvinosarudzwa zvakazvimiririra zvinodzorwa zvabuda [Fail-Safe (NC) kana Fail-Secure (NO)] uye masere (8) akazvimirira anodzora Fomu “C” Relay zvabuda.

Mufananidzo 6 - eFlow104NKA8(D)

Optional Rechargeable Stand-by Battery yeUL294 Applications
Cherechedza: 12V mabhatiri anodiwa
ULC-S319 kuiswa.

KUCHENJERA: Shandisa maviri (2) 12VDC anomira-nemabhatiri.
Chengetedza magetsi-akaganhurirwa wiring akaparadzana neasina-simba-shoma.
Shandisa zvishoma 0.25” nzvimbo.
12AH Rechargeable mabhatiri ndiwo mabhatiri makuru anogona kukwana mune ino yakavharwa.
A UL-yakanyorwa bhatiri rekunze rakavharirwa rinofanira kushandiswa kana uchishandisa 40AH kana 65AH mabhatiri.

Yakajairika Yekushandisa Dhiyagiramu:

Mufananidzo 7

Hook-Up Diagrams:

Mufananidzo 8 - Daisy-chaining imwe kana kupfuura ACMS8 (CB) zvikamu.
EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Non-Latching.

Mufananidzo 9 - Daisy-chaining imwe kana kupfuura ACMS8 (CB) zvikamu.
EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Latching Single Reset.

Fig. 10 – Daisy chaining one or more ACMS8(CB) units.
EOL Jumper [EOL JMP] inofanira kuiswa munzvimbo yeEOL. Latching Individual Reset.

Hook-Up Diagrams:

Fig. 11 - Polarity reversal input kubva ku FACP inoisa chiratidzo chedunhu kubuda (polarity inotaridzirwa mumamiriro e alarm). Non-Latching.	Fig. 12 - Polarity reversal input kubva ku FACP inoisa chiratidzo chedunhu kubuda (polarity inotaridzirwa mumamiriro e alarm). Latching.

Fig. 13 - Kazhinji Yakavharwa trigger input (Non-Latching).	Fig. 14 - Kazhinji Yakavharwa trigger input (Latching).

Fig. 15 - Kazhinji Open trigger input (Non-Latching).	Fig. 16 - Kazhinji Open trigger input (Latching).

Enclosure Dimensions (BC400):
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix haina mhosva kune chero zvikanganiso zve typographical.
140 58th Street, Brooklyn, New York 11220 USA | foni: 718-567-8181 | fax: 718-567-9056
websaiti: www.altronix.com | e-mail: info@altronix.com | Hupenyu hwese Warranty
IIeFlow104NKA8(D)
G29U

Zvinyorwa / Zvishandiso

Altronix eFlow104NA8 Series Dual Output Access Power Controllers [pdf] Installation Guide
eFlow104NA8 Series Dual Output Access Power Controllers, eFlow104NA8 Series, Dual Output Access Power Controllers, Access Power Controllers, Power Controllers, Controllers.

References

User Manual