eFlow104NA8 Series Dual fitarwa
Samun Masu Gudanar da Wuta
Jagoran Shigarwa

eFlow104NA8 Series Dual Output Access Power Controllers

eFlow104NKA8

• 12VDC ko 5VDC har zuwa 6A da/ko 24VDC har zuwa 10A (240W jimlar ƙarfin) zaɓaɓɓu ta hanyar fitarwa.
• Takwas (8) abubuwan da ke da kariya ta fuse.
• Takwas (8) Zaɓaɓɓen Rashin Amincewa, Rashin Amintacce, ko Form "C" busassun kayan aiki
• Cire haɗin žararrawar wuta ana iya zaɓar ta fitarwa
• Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura masu nau'in gel

eFlow104NKA8D

• 12VDC ko 5VDC har zuwa 6A da/ko 24VDC har zuwa 10A (240W jimlar ƙarfin) zaɓaɓɓu ta hanyar fitarwa.
• Takwas (8) Matsayi na 2 mai iyakacin ikon PTC masu kariya.
• Takwas (8) Zaɓaɓɓen Rashin Amincewa, Rashin Amintacce, ko Form "C" busassun kayan aiki.
• Ana iya zaɓin cire haɗin ƙararrawar wuta ta hanyar fitarwa.
• Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura masu nau'in gel.

Saukewa: eFlow104NKA8-072220

Kamfanin Shiga: _______________ Wakilin Sabis. Suna: ________________________________________________
Adireshi: _____________________________________________ Waya #: __________________

Ƙarsheview:

Altronix eFlow104NKA8 da eFlow104NKA8D suna rarrabawa da canza iko don samun damar tsarin sarrafawa da kayan haɗi. Suna juyar da shigarwar 120VAC 60Hz zuwa takwas (8) sarrafa kayan sarrafawa na 12VDC ko 24VDC masu zaman kansu. Zane-zanen shigarwa biyu na Mai Gudanar da Wutar Wuta yana ba da damar sarrafa wutar lantarki daga masana'anta guda biyu (2) da aka girka masu zaman kansu masu zaman kansu.tage 12 ko 24VDC Altronix samar da wutar lantarki zuwa takwas (8) fiusi mai sarrafa kansa (eFlow104NKA8) ko PTC (eFlow104NKA8D) abubuwan da aka karewa. Ana iya juyar da abubuwan da aka fitar da wutar lantarki zuwa lambobi masu busassun nau'in "C". Ana kunna fitarwa ta hanyar buɗaɗɗen mai tattarawa, yawanci buɗewa (NO), yawanci rufe (NC) shigar da busasshen faɗakarwa, ko rigar fitarwa daga Tsarin Kulawa, Mai karanta Kati, faifan maɓalli, Maɓallin turawa, PIR, da sauransu eFlow104NKA8(D) zai ikon hanya zuwa nau'ikan na'urorin sarrafa kayan aiki iri-iri ciki har da Makullin Mag, Harshen Wutar Lantarki, Masu riƙe da Ƙofa na Magnetic, da dai sauransu. Abubuwan da aka fitar za su yi aiki a cikin yanayin rashin aminci da/ko rashin aminci. Fuskar FACP tana ba da damar Ƙaddamar Gaggawa, da Kula da Ƙararrawa, ko ana iya amfani da su don jawo wasu na'urori masu taimako. Siffar cire haɗin ƙararrawar wuta ana iya zaɓa ɗaya ɗaya don kowane ko duka na takwas (8). Masu haɗin spade suna ba ku damar ikon sarkar daisy zuwa maɗaukakin ACMS8(CB). Wannan fasalin yana ba ku damar rarraba wutar lantarki akan ƙarin abubuwan fitarwa don manyan tsarin.

Ƙayyadaddun Takaddun Tsaye:

Baturi	Burg. Aikace-aikace 4h ku. Tsaya tukuna/ 15 min. Ƙararrawa	Aikace-aikacen Wuta 24h ku. Tsaya tukuna/ 5 min. Ƙararrawa	Ikon shiga Aikace-aikace Tsaya tukuna
7AH	0.4A/10A	N/A	Minti 5/10A
12A11	1A/10A	0.3A/10A	Minti 15/10A
40A11	6A/10A	1.2A/10A	Sama da Awa 2/10A
65A11	6A/10A	1.5A/10A	Sama da Awa 4/10A

Ƙayyadaddun bayanai:

Abubuwan shigarwa:
eFlow104NB:

• 120VAC, 60Hz, 4.5A.
  ACMS8/ACMS8CB:
• Abubuwan shigar da abubuwa takwas (8)
  a) Abubuwan da aka saba buɗewa (NO) (bushe lambobin sadarwa).
  b) Abubuwan shigar da aka saba rufe (NC) (bushen lambobi).
  c) Buɗe abubuwan shigar da mai tarawa.
  d) Rigar Input (5VDC - 24VDC) tare da resistor 10K
  e) Duk wani haɗuwa na sama.

Abubuwan da aka fitar:
Ƙarfi:

• 12VDC ko 5VDC har zuwa 6A, 24VDC har zuwa 10A
  (240W jimlar iko).
• Ƙarfin Ƙarfi na Class 2 mai iyaka
  rated @ 1A (ba a canza ba).
• Ƙarfafawatage kariya.
  ACMS8:
• Abubuwan da aka kare-fuse mai ƙididdigewa @ 2.5A ga kowane fitarwa, mara iyaka. Jimlar fitarwa 6A max.
  Kada ku wuce daidaitattun ƙimar samar da wutar lantarki.
  ACMS8CB:
• Abubuwan da ke da kariya na PTC wanda aka ƙididdige @ 2A akan kowace fitarwa, Class 2-iyakantacce. Jimlar fitarwa 6A max.
  Kada ku wuce daidaitattun ƙimar samar da wutar lantarki.
• Takwas (8) abubuwan da za a iya sarrafawa masu zaman kansu ko takwas (8) abubuwan da aka sarrafa na Form "C" masu zaman kansu (duba ƙasa don ƙididdigewa):
  a) Fail-Safe da/ko Rashin-Tsarowar samar da wutar lantarki.
  b) Form "C" relays mai ƙididdigewa @ 2.5A. 12VDC,
  0.6 Factor Power (ACMS8 kawai).
  c) Abubuwan wutar lantarki na taimako (ba a kunna ba).
  d) Duk wani hade na sama.
• Za'a iya saita abubuwan da aka fitar guda ɗaya zuwa matsayin KASHE don yin hidima (saitin jumper zuwa matsayi na tsakiya).
  Ba ya aiki ga busasshiyar tuntuɓar aikace-aikacen.
• Ana iya zaɓar kowane ɗayan fiusi takwas (8) na fuse/PTC da aka kariyar wutar lantarki don bin ikon shigar da wutar lantarki 1 ko Input 2. Ƙimar fitarwa.tage na kowane fitarwa iri ɗaya ne da shigar voltage na shigar da aka zaɓa.
• Damuwawar tiyata.

Ƙimar Fuse/PTC:
eFlow104NB:

• An ƙididdige fis ɗin shigarwa a 6.3A/250V.
• Fuskar baturi 15A/32V.
  ACMS8:
• An ƙididdige babban fis ɗin shigarwa 15A/32V.
• Ana ƙididdige fis ɗin fitarwa 3A/32V.
  ACMS8CB:
• Babban shigarwar PTC an ƙididdige 9A.
• Ana ƙididdige fitowar PTC 2A.

Ajiyayyen baturi (eFlow104NB):

• Caja da aka gina a ciki don rufaffiyar gubar acid ko nau'in batura masu nau'in gel.
• Matsakaicin caji na yanzu 1.54A.
• Canja atomatik zuwa baturin jiran aiki lokacin da AC ta gaza.
  Canja wurin zuwa ƙarfin baturi yana nan take ba tare da katsewa ba.

Kulawa (eFlow104NB):

• AC ta kasa kulawa (form "C" lambobin sadarwa).
• gazawar baturi & kasancewar sa ido (form "C" lambobin sadarwa).
• Ƙarfin wutar lantarki. Yana rufe tashoshin fitarwa na DC idan baturi voltage ya faɗi ƙasa 71-73% don raka'a 12V da 70-75% don raka'a 24V (dangane da wutar lantarki). Yana hana zurfafa fitar da baturi.

Kashe Haɗin Ƙararrawar Wuta:
eFlow104NB:

• Cire haɗin Ƙararrawar Wuta da ake kulawa (latching ko mara latching) 10K EOL resistor. Yana aiki akan fararwa na yau da kullun (NO) ko rufaffiyar (NC).

ACMS8 (CB):

• Cire haɗin ƙararrawa na Wuta (latching ko rashin latching) ana iya zaɓin ɗaiɗaiku don kowane ko duka na takwas (8).
  Zaɓuɓɓukan shigar da ƙararrawar wuta:
  a) Buɗe [NO] ko yawanci rufe [NC] shigar da busassun lamba. Shigar da juyar da polarity daga da'irar siginar FACP.
• An ƙididdige shigarwar FACP WET 5-30VDC 7mA.
• Shigar da FACP EOL yana buƙatar mai tsayayyar ƙarshen layin 10K.
• FACP fitarwa relay [NC]:
  Ko dai Dry 1A/28VDC, 0.6 Power Factor ko
  10K juriya tare da [EOL JMP] cikakke.

Alamun gani:
eFlow104NB:

• Green AC LED: Yana nuna 120VAC yanzu.
• Red DC LED: Yana nuna fitowar DC.
  ACMS8 (CB):
• Red LEDs: Nuna abubuwan da aka jawo.
• Blue LED: Yana nuna cire haɗin FACP ya jawo.
• Mutum
  Voltage LEDs: Nuna 12VDC (Green) ko 24VDC (Ja).

Muhalli:

• Yanayin aiki: 0ºC zuwa 49ºC na yanayi.
• Humidity: 20 zuwa 85%, mara taurin kai.

Girman Rukunin (kimanin H x W x D):
15.5" x 12" x 4.5"
(393.7mm x 304.8mm x 114.3mm).

Umarnin Shigarwa:

Hanyoyin wayoyi za su kasance daidai da Lambar Lantarki ta Ƙasa/NFPA 70/NFPA 72/ANSI, Lambar Lantarki ta Kanada, kuma tare da duk lambobin gida da hukumomi masu iko. An yi nufin samfurin don amfanin cikin gida kawai.

1. Dutsen naúrar a wurin da ake so. Yi alama da ramuka a bango don yin layi tare da manyan maɓallan maɓalli guda biyu a cikin shingen. Shigar da manyan haɗe-haɗe biyu da sukurori a bango tare da ɗumbin kawunan suna fitowa. Sanya ramukan maɓalli na sama na katangar sama da sukurori biyu na sama, matakin, kuma amintattu. Alama matsayi na ƙananan ramuka biyu. Cire shingen. Hana ƙananan ramuka kuma shigar da masu ɗaure biyu. Sanya ramukan maɓalli na sama sama biyu na sama. Shigar da ƙananan sukurori biyu kuma tabbatar da ƙarfafa duk screws (Ƙaƙƙarfan Ƙirar, shafi 8). Tsare shingen zuwa ƙasan ƙasa.
2. Tabbatar da duk masu tsalle-tsalle masu fitarwa [PWR1] - [PWR8] an sanya su a cikin KASHE (tsakiya) matsayi (Fig. 1, shafi 3).
3. Haɗa ikon AC da ba a kunna ba (120VAC 60Hz) zuwa tashoshi masu alama [L, N] ana iya gani ta ruwan tabarau na LED akan ƙofar katangar. Yi amfani da 14 AWG ko mafi girma don duk haɗin wutar lantarki. Amintaccen koren waya yana kaiwa zuwa ƙasa. Ajiye wayoyi masu iyaka dabam dabam da wayoyi marasa iyaka (Input 120VAC 60Hz, Wayoyin Baturi). Dole ne a samar da tazara mafi ƙarancin 0.25.
   HANKALI: Kar a taɓa sassa na ƙarfe da aka fallasa. Kashe wutar da'irar reshe kafin shigarwa ko kayan aiki. Babu sassan da za a iya amfani da su a ciki.
   Koma shigarwa da sabis zuwa ƙwararrun ma'aikatan sabis.
4. Saita kowane fitarwa [OUT1] - [OUT8] zuwa hanyar wutar lantarki daga Shigarwar 1 ko 2 (Fig. 1, shafi 3).
   Lura: Auna fitarwa voltage kafin haɗa na'urori. Wannan yana taimakawa guje wa lalacewa mai yuwuwa.
5. Kashe wuta kafin haɗa na'urori.
6. Zaɓuɓɓukan fitarwa: eFlow104NKA8(D) zai samar da wutar lantarki har takwas (8) da aka canza ko kuma takwas (8) busassun nau'in fitowar "C", ko duk wani haɗin duka biyun da aka canza da sigar "C", da takwas (8) ba a kunna ba. karin ƙarfin lantarki.
   Abubuwan Wutar Wuta da aka Canja: Haɗa madaidaicin shigarwar (-) na na'urar da ake kunna wuta zuwa tasha mai alama [COM].
   • Don Ƙarfafa-Safe aiki haɗa ingantaccen shigarwar (+) na na'urar da ake kunna wutar lantarki zuwa tashar da aka yiwa alama [NC].
   • Don Ƙarfafa Amintaccen aiki haɗa ingantaccen shigarwar (+) na na'urar da ake kunna wutar lantarki zuwa tasha mai alama [NO].
   Form "C" abubuwan da aka fitar:
   Lokacin da ake son fitar da nau'in "C", dole ne a sanya madaidaicin jumper (1-8) a cikin KASHE (Fig. 7, shafi 9). A madadin, ana iya cire fis ɗin fitarwa mai dacewa (1-8) (eFlow104NKA8 kawai).
   Haɗa mummunan (-) na wutar lantarki kai tsaye zuwa na'urar kullewa.
   Haɗa tabbataccen (+) na wutar lantarki zuwa tasha mai alama [C].
   • Don Ƙarfafa-Safe aiki haɗa tabbataccen (+) na na'urar da aka kunna zuwa tashar da aka yiwa alama [NC].
   • Don Ƙarfafa Amintaccen aiki haɗa tabbataccen (+) na na'urar da ake kunna wuta zuwa tasha mai alama [NO].
   Busassun adireshi masu ƙima @ 2.5A, 28VDC.
   Fitowar wutar lantarki (ba a kunna):
   Haɗa ingantaccen shigarwar (+) na na'urar da ake kunna wuta zuwa tasha mai alama [C] da mummunan (-) na na'urar da ake kunna wutar zuwa tasha mai alama [COM]. Ana iya amfani da fitarwa don samar da wuta ga masu karanta katin, maɓalli, da sauransu.
7. Kunna babban wutar lantarki bayan an haɗa duk na'urori.
8. Zaɓuɓɓukan Ƙarfafa shigarwa:
   Lura: Idan ba a yi amfani da cire haɗin Ƙararrawar Wuta ba, haɗa 10K ohm resistor zuwa tashoshi masu alama [GND da EOL], da haɗa jumper zuwa tashoshi masu alamar [GND, RST].
   Shigarwa Akan Buɗe (NO):
   Slide shigar da dabaru na Slide DIP canzawa zuwa cikin KASHE matsayi don [Canja 1-8] (Fig. 2, a dama). Haɗa wayoyi zuwa tashoshi masu alamar [+ INP1 -] zuwa [+ INP8 -].
   Shigarwar Akan Rufe (NC):
   Maɓallin shigar da Slide Slide DIP mai sauyawa zuwa matsayin ON don [Canja 1-8] (Hoto na 2, a dama). Haɗa wayoyi zuwa tashoshi masu alamar [+ INP1 -] zuwa [+ INP8 -].
   Buɗe Shigar Mai Tari:
   Haɗa shigar da buɗaɗɗen shigarwar nutsewar mai tarawa zuwa tashar da aka yiwa alama [+ INP1 -] zuwa [+ INP8 -].
   Jika (Voltage) Kanfigareshan shigarwa:
   A hankali lura da polarity, haɗa voltage shigar da wayoyi masu jawowa da kuma samar da resistor 10K zuwa tashoshi masu alamar [+ INP1 -] zuwa [+ INP8 -].
   Idan ana amfani da voltage don kunna shigarwa - saita madaidaicin INP Logic sauyawa zuwa matsayin "KASHE".
   Idan cire voltage don kunna shigarwa - saita madaidaicin INP Logic sauyawa zuwa matsayi "ON".
9. Zaɓuɓɓukan Interface Ƙararrawa:
   Rufe [NC], yawanci buɗe [NO] shigarwar ko shigar da juzu'i na polarity daga da'irar siginar FACP zai haifar da zaɓin abubuwan da aka zaɓa. Don kunna cire haɗin FACP don fitarwa kunna maɓallin DIP daidai [SW1-SW8] ON.
   Don musaki cire haɗin FACP don fitarwa kunna maɓallin DIP daidai [SW1-SW8] KASHE. Maɓallin yana tsaye kai tsaye zuwa hagu na Tashar Interface Interface Ƙararrawa. Yawan Buɗe Shigarwa:
   Waya gudun ba da sanda na FACP ɗin ku da resistor 10K a layi daya akan tashoshi masu alamar [GND] da [EOL].
   Shigarwa Akan Rufe:
   Wire relay na FACP ɗin ku da resistor 10K a jere akan tashoshi masu alamar [GND] da [EOL].
   FACP Siginar Ƙarfafa Shigar da Wuta:
   Haɗa tabbataccen (+) da korau (-) daga fitowar sigina na FACP zuwa tashoshi masu alama [+ FACP -]. Haɗa FACP EOL zuwa tashoshi masu alamar [+ RET -] (an yi la'akari da polarity a cikin yanayin ƙararrawa).
   Cire Haɗin Ƙararrawar Wuta mara Latsawa: Haɗa mai tsalle zuwa tashoshi masu alama [GND, RST].
   Cire Haɗin Ƙararrawar Wuta: Haɗa NO na yau da kullun buɗe sake saiti zuwa tashoshi masu alama [GND, RST].
10. FACP Dry NC fitarwa:
    Haɗa na'urar da ake so don buɗewa ta busasshiyar fitowar lamba ta naúrar zuwa tashoshi masu alama [NC] da [C].
    Lokacin da aka kiyaye [EOL JMP], abin da ake fitarwa shine juriya na 0 Ohm a cikin yanayin al'ada.
    Lokacin da aka yanke [EOL JMP], juriya 10k za a wuce zuwa na'ura ta gaba lokacin da ke cikin yanayin al'ada.
11. Haɗin Batir na tsaye (Hoto na 6, shafi na 8):
    Don aikace-aikacen Ikon Samun damar Amurka batura na zaɓi ne. Ana buƙatar batura don shigarwa na Kanada (ULC-S319). Lokacin da ba a yi amfani da batura ba, asarar AC zai haifar da asarar juzu'in fitarwatage.
    Lokacin da ake son amfani da batura masu aiki, dole ne su zama nau'in gubar acid ko gel.
    Haɗa baturin zuwa tashoshi masu alama [- BAT +] (Fig. 4g, shafi 6). Yi amfani da batura guda biyu (2) 12VDC da aka haɗa a jeri don aikin 24VDC (an haɗa da jagororin baturi). Yi amfani da batura - Castle CL1270 (12V/7AH), CL12120 (12V/12AH), CL12400 (12V/40AH), CL12650 (12V/65AH) batura ko UL gane batir BAZR2 da BAZR8 na ƙimar da ta dace.
12. Abubuwan Baturi da Kulawar AC (Hoto 4, shafi 8):
    Ana buƙatar haɗa na'urori masu ba da rahoton matsala masu kulawa zuwa abubuwan da aka yiwa alama [AC Fail, BAT Fail] da abubuwan sa ido na sa ido mai alamar [NC, C, NO] zuwa na'urorin sanarwar gani da suka dace.
    Yi amfani da 22 AWG zuwa 18 AWG don gazawar AC & Ƙananan / Babu rahoton baturi.
13. Don jinkirta rahoton AC na tsawon awanni 2. saita maɓallin DIP [AC Jinkiri] zuwa matsayin KASHE (Fig. 4c, shafi 6).
    Don jinkirta rahoton AC na minti 1. saita canza DIP [AC Jinkiri] zuwa ON matsayi (Fig. 4c, shafi 6).
14. Cire Haɗin Ƙararrawar Wuta (Hoto 4c, shafi 6):
    Don kunna Cire Haɗin Ƙararrawar Wuta saita maɓallin DIP [Rufewa] zuwa matsayin ON.
    Don kashe Ƙararrawar Ƙararrawar Wuta Cire haɗin wuta saita maɓallin DIP [Rufewa] zuwa matsayin KASHE.
15. Shigar da tampya canza:
    Dutsen UL Jerin tamper canza (samfurin Altronix TS112 ko daidai) a saman shingen. Zamar da tampmadaidaicin madaidaicin madaidaicin zuwa gefen shingen kusan 2” daga gefen dama (Fig. 6a, shafi 8).
    Haɗa tampcanza wayoyi zuwa shigar da Panel Control Panel ko na'urar da aka jera UL mai dacewa. Don kunna siginar ƙararrawa buɗe ƙofar kewayen.

Waya:

Yi amfani da 18 AWG ko mafi girma don duk ƙaramin ƙarfitage ikon haɗi.
Lura: Kula da kiyaye iyakokin da'irori mai iyaka daga wayoyi marasa iyaka (120VAC, Baturi).

Kulawa:

Ya kamata a gwada naúrar aƙalla sau ɗaya a shekara don aikin da ya dace kamar haka:
Fitarwa Voltage Gwaji: A ƙarƙashin yanayin kaya na yau da kullun, fitarwar DC voltage ya kamata a duba don daidai voltage matakin eFlow104NB: 24VDC mai ƙididdigewa @ 10A max.
Gwajin baturi: Ƙarƙashin nauyin al'ada, yanayi duba cewa cajin baturi ya cika, duba ƙayyadadden voltage (24VDC @ 26.4) duka a tashar baturi da kuma a tashoshin allon da aka yiwa alama [- BAT +] don tabbatar da cewa babu raguwa a cikin wayoyi masu haɗin baturi.
LuraMatsakaicin caji na yanzu ƙarƙashin fitarwa shine 1.54A.
Lura: Rayuwar baturi da ake tsammani shine shekaru 5, duk da haka, ana bada shawarar canza batura a cikin shekaru 4 ko ƙasa da haka idan an buƙata.

Hoto 4 - Kanfigareshan Hukumar eFlow104N

Matsala/Lokaci Iyakataccen Gargaɗi na Batura Masu Tsaya:
Don biyan bukatun ULC S318-96, Dole ne a haɗa da'irar Gargaɗi mai iyaka don sanarwa na gida ko na nesa tare da Amber ko Red LED don nuna Matsalolin DC (ƙananan baturi, asarar baturi ko lokacin da 95% na baturin jiran aiki ya kasance. depleted). Haɗa da'irar zuwa lambobin sadarwa na Batt Fail zuwa shigar da ta dace na UL Listed Burglar Ƙararrawa ko Cibiyar Kulawa ta Samun dama. Hoton da ke gaba yana nuna da'irar da ake buƙata don shelar gida.

Hoto 5 - Alamar matsalar baturi
Don amfanin Kanada, ja mai nuna lamp dole ne a bayyane daga wajen wannan shingen.
Waya ƙafa ɗaya na UL Jerin, tushen wutar lantarki mai iyaka zuwa alamar lamp.
Waya kafa na biyu na tushen wutar lantarki zuwa alamar lamp a jeri tare da baturi kasa relay contact terminals alama [BAT FAIL – C, NO] (Hoto 5, shafi. 6).

LED Diagnostics:

eFlow104NB Power Supply/Caja

Ja (DC)	Green (AC/AC1)	Matsayin Samar da Wuta
ON	ON	Yanayin aiki na al'ada.
ON	KASHE	Asarar AC. Baturin jiran aiki yana ba da wuta.
KASHE	ON	Babu fitarwa na DC.
KASHE	KASHE	Asarar AC. An cire ko babu baturi mai jiran aiki. Babu fitarwa na DC.

ACMS8 da ACMS8CB Mai Kula da Wutar Lantarki

LED	ON	KASHE
LED 1-LED 8 (ja)	Relay(s) na fitar da kuzari.	Relay(s) na fitar da kuzari.
FUSKA	An kunna shigar da FACP (yanayin ƙararrawa).	FACP na al'ada (yanayin rashin ƙararrawa).
Koren Fitowa 1-8	Saukewa: 12VDC	—
Jajayen Fitowa 1-8	Saukewa: 24VDC	—

Shaidar Ƙarshe:
eFlow104NB Power Supply/Caja

Labarin Ƙarshe	Aiki/Bayyana
L, N	Haɗa 120VAC 60Hz zuwa waɗannan tashoshi: L zuwa zafi, N zuwa tsaka tsaki (mara iyaka) (Fig. 4a, shafi 6).
- DC +	24VDC nominal @ 10A ci gaba da fitarwa (fitarwa mara iyaka) (Fig. 417, shafi 6).
Ana Kula da Ƙaddamar da EOL	Wuta Ƙararrawa Interface yana jawo shigarwar shigarwa daga gajere ko FACP. Ana iya buɗe abubuwan shigar da ƙara a kullum kuma a rufe kullum daga da'irar fitarwa ta FACP (shigarwa mai iyaka) (Hoto 4d, shafi 6).
A'a, Sake saitin GND	FACP dubawa latching ko rashin latching (ikon iyaka) (Fig. 4e, shafi 6).
+ AUX -	Ƙarfin Ƙarfi 2 mai iyakataccen fitarwa mai iyaka @ 1 A (ba a kunna ba) (Fig. 41, shafi 6).
AC Fail NC, C, NO	Yana nuna asarar wutar AC, misali haɗi zuwa na'ura mai ji ko ƙararrawa. Relay yawanci yana samun kuzari lokacin da ƙarfin AC ya kasance. Ƙimar tuntuɓar 1A @ 30VDC (mai iyakacin ƙarfi) (Hoto 4b, shafi 6).
Bat Fail NC, C, NO	Yana nuna ƙarancin yanayin baturi, misali haɗi zuwa sashin ƙararrawa. Relay yawanci yana samun kuzari lokacin da ƙarfin DC ya kasance. Ƙimar lamba 1A @ 30VDC. Ana ba da rahoton cire baturi a cikin mintuna 5. An ba da rahoton sake haɗa baturi a cikin minti 1 (iyakantaccen iko) (Fig. 4b, shafi 6).
- BAT +	Haɗin baturi na tsaye. Matsakaicin cajin na yanzu 1.54A (mara iyaka-mai iyaka) (Fig. 4g, shafi 6).

ACMS8 da ACMS8CB Mai Kula da Wutar Lantarki

Labarin Ƙarshe	Aiki/Bayyana
PWR1-	An haɗa masana'anta zuwa eFlow104NB. Kar a yi amfani da waɗannan tashoshi.
PWR2-	Kamfanin da aka haɗa zuwa VR6 voltage regulator. Kar a yi amfani da waɗannan tashoshi.
+ INP1 - ta + INP8 -	Takwas (8) mai zaman kansa Buɗewa ta al'ada (NO), An rufe ta ta al'ada (NC), Buɗaɗɗen Mai Tari ko Rigar shigar da Jika.
C, NC	FACP Dry NC fitarwa mai ƙididdigewa 1A/28VDC © 0.6 Factor Power. Matsayi na 2 mai iyaka. Tare da EOL JMP cikakke, zai samar da juriya na 10k a cikin yanayin al'ada.
GND, RST	FACP interface latching ko rashin latching. NO bushe shigarwa. Matsayi na 2 mai iyaka. Don a gajarta don ƙirar FACP mara amfani ko Latch FACP sake saiti.
GND, EOL	EOL Tashoshin shigarwar FACP mai kulawa don juyar da aikin FACP na polarity. Matsayi na 2 mai iyaka.
- F, + F, - R, + R	Shigar da siginar siginar FACP da tasha. Matsayi na 2 mai iyaka.
Fitowa ta 1 ta hanyar fitarwa ta 8 NO C, NC, COM	Takwas (8) zaɓaɓɓun abubuwan sarrafawa masu zaman kansu [Fail-Safe (NC) ko Fail-Secure (NO)] da takwas (8) abubuwan sarrafawa na Form “C” masu zaman kansu.

Hoto 6 - eFlow104NKA8(D)

Batir na tsaye mai caji na zaɓi don Aikace-aikacen UL294 Lura: Ana buƙatar batir 12V ULC-S319 shigarwa.

Batir na tsaye mai caji na zaɓi don Aikace-aikacen UL294 Lura: Ana buƙatar batir 12V ULC-S319 shigarwa.

HANKALI: Yi amfani da baturan jiran aiki guda biyu (2) 12VDC.
Kiyaye iyakataccen wayoyi daban da mara iyaka.
Yi amfani da mafi ƙarancin tazarar 0.25 inci.
12AH batura masu caji sune manyan batura waɗanda zasu iya dacewa da wannan shingen.
Dole ne a yi amfani da shingen baturi na waje mai jera UL idan ana amfani da batura 40AH ko 65AH.

Tsarin aikace-aikace na yau da kullun:

Hoto 7

Zane-zane na Ƙunƙwasa:

Hoto 8 – Daisy- sarkar daya ko fiye ACMS8(CB) raka'a.
Ya kamata a shigar da EOL Jumper [EOL JMP] a matsayin EOL. Rashin Latsawa.

Hoto 9 – Daisy- sarkar daya ko fiye ACMS8(CB) raka'a.
Ya kamata a shigar da EOL Jumper [EOL JMP] a matsayin EOL. Latching Single Sake saiti.

Hoto 10 – Daisy sarkar daya ko fiye ACMS8(CB) raka'a.
Ya kamata a shigar da EOL Jumper [EOL JMP] a matsayin EOL. Latching Mutum Sake saitin.

Zane-zane na Ƙunƙwasa:

Hoto 11 – Shigar da juyar da polarity daga fitarwa na sigina na FACP (an yi nuni da polarity a yanayin ƙararrawa). Rashin Latsawa.	Hoto 12 – Shigar da juyar da polarity daga fitarwa na sigina na FACP (an yi nuni da polarity a yanayin ƙararrawa). Latching.
Hoto na 13 – Shigar da faɗakarwa da ke rufewa (Ba Latching).	Hoto na 14 – Rufe shigarwar faɗakarwa (Latching).
Hoto 15 – Buɗe shigar da fararwa ta al'ada (Ba Latching).	Hoto 16 – Buɗe shigar da faɗakarwa ta al'ada (Latching).

Girman Rukunin (BC400):
15.5" x 12" x 4.5" (393.7mm x 304.8mm x 114.3mm)

Altronix baya da alhakin kowane kuskuren rubutu.
140 58th Street, Brooklyn, New York 11220 USA | waya: 718-567-8181 | fax: 718-567-9056
website: www.altronix.com | e-mail: info@altronix.com | Garanti na rayuwa
IIeFlow104NKA8(D)
G29U

Takardu / Albarkatu

Altronix eFlow104NA8 Series Dual Output Access Power Controllers [pdf] Jagoran Shigarwa eFlow104NA8 Series Dual Output Access Power Controllers, eFlow104NA8 Series, Dual Output Access Power Controllers, Access Power Controllers, Power Controllers, Controllers

Magana

• Manual mai amfani