Lethathamo la lintlha tsa ACMS12
Kopano e nyane
Fumana Balaoli ba Matla
Tataiso ea ho Kena
ACMS12 Series Sub Assembly Access Power Controllers
Mefuta e kenyeletsa:
ACMS12
– Leshome le metso e ‘meli (12) Fuse Protected Outputs
ACMS12CB
– Leshome le metso e ‘meli (12) PTC Pro Protected
Fetileview:
Altronix ACMS12/ACMS12CB ke li-sub-assemblies tse etselitsoeng ho sebelisoa Altronix BC300, BC400, Trove1, Trove2 le Trove3 e koetsoeng le likarolo tsa matla a Maximal. Moralo oa likarolo tse peli oa Access Power Controller o lumella matla ho tsamaisoa ho tloha ho tse peli (2) tse ikemetseng tse tlasetage 12 kapa 24VDC Altronix lisebelisoa tsa matla ho tse leshome le metso e 'meli (12) tse laoloang ka mokhoa o ikemetseng (ACMS12) kapa PTC (ACMS12CB) lihlahisoa tse sirelelitsoeng. Dipoelo di kenngwa tshebetsong ke sink e bulehileng ya pokello, eo ka tlwaelo e butsweng (NO), eo hangata e kwalwang (NC) e omileng ya ho kenya letsoho, kapa tlhahiso e metsi ho tswa ho Access Control System, Card Reader,Keypad, Push Button, PIR, jj. ACMS12(CB) e tla matla a tsela ho ea ho lisebelisoa tse fapaneng tsa taolo ea phihlello ho kenyelletsa Mag Locks, Motlakase Strikes, Magnetic Door Holders, joalo-joalo Outputs e tla sebetsa ka mekhoa ea Fail-Safe kapa Fail-Secure. FACP Interface e nolofalletsa Emergency Egress, Alarm Monitoring, kapa e ka sebelisoa ho kenya lisebelisoa tse ling tse thusang. Tšobotsi ea ho khaola alamo ea mollo e ka khethoa ka bomong bakeng sa liphetho leha e le life kapa tse leshome le metso e 'meli (12). Lihokelo tsa likharebe li u lumella ho kenya matla a mahlahahlaha ho li-module tse ngata tsa ACMS12(CB). Karolo ena e u lumella ho aba matla holim'a liphetho tse ngata bakeng sa litsamaiso tse kholoanyane.
Litlhaloso:
Keletso Voltage:
- Keletso 1: Matla a 12 kapa 24VDC Altronix.
- Keletso 2: 12 kapa 24VDC Altronix phepelo ea motlakase kapa 5 kapa 12VDC ho tsoa ho VR6 Regulator.
- Kena Hona Joale:
ACMS12: 20A kakaretso
ACMS12CB: 16A kakaretso. - Litlhahiso tse leshome le metso e 'meli (12) tse ka khethoang ka botsona:
a) Ka tloaelo bula (NO) tse kenang (mabitso a omileng).
b) Lisebelisoa tse tloaelehileng tse koetsoeng (NC) (li-contacts tse omileng).
c) Bula lisebelisoa tsa sink ea pokello.
d) Kenyelletso ea Metsi (5VDC - 24VDC) e nang le mohanyetsi oa 10K
e) Motsoako ofe kapa ofe oa tse ka holimo.
Liphetho:
- ACMS12: Liphetho tse sirelelitsoeng tsa Fuse li lekantsoe @ 2.5A ka tlhahiso, ha e na moeli oa matla.
Kakaretso ea tlhahiso 20A max.
Sheba Input/Output Voltage Litekanyo, leq. 7.
ACMS12CB: Liphetho tse sirelelitsoeng tsa PTC li behiloe @ 2A ka tlhahiso, Sehlopha sa 2 se na le matla a fokolang.
Kakaretso ea tlhahiso 16A max.
Se ke oa feta litekanyetso tsa phepelo ea motlakase ka bomong.
Sheba Input/Output Voltage Litekanyo, leq. 7.
Kakaretso ea hona joale ha ea lokela ho feta max. tekanyo ea hona joale ea phepelo ea motlakase e sebelisitsoeng molemong o mong le o mong.
Sheba Sephetho se Phahameng sa Lisebelisoa tsa Matla a Altronix. - Tse leshome le metso e 'meli (12) tse ka khethoang ka boikemelo tsa Fail-Safe kapa Fail-Sireletsehile matla a tsoang.
- Liphetho tsa motho ka mong li ka hlophisoa ho OFF boemo bakeng sa ts'ebeletso (output jumper set to the middle).
- Lintho tse hlahisoang li ka khethoa ho latela matla Input 1 kapa Input 2. Output voltage ea tlhahiso e 'ngoe le e 'ngoe e tšoana le matla a ho kenyatage ea tse kentsoeng.
Sheba Input/Output Voltage Litekanyo, leq. 7. - Khatello e phahameng.
Khaola Alarm ea Mollo:
- Ho khaoha ha Alarm ea Mollo (ho latching kapa ho se lache) ho ka khethoa ka bonngoe bakeng sa liphetho tse leshome le metso e 'meli (12).
Likhetho tsa ho kenya Alarm ea Mollo:
a) Hangata e bula [NO] kapa hangata e koetsoe [NC] e omileng ea ho kenya. Kenyelletso ea ho khutlisa polarity ho tsoa ho potoloho ea matšoao a FACP. - FACP input WET ke rated 5-30VDC 7mA.
- Ho kenya FACP EOL e hloka pheletso ea 10K ea mohanyetsi oa mohala.
- FACP output relay [NC]:
Ekaba FACP dry NC output kapa
Khokahano ea ka hare ea EOL ho ACMS12(CB) e latelang.
Lintlha tsa ACMS12 Fuse:
- Li-fuse tsa mantlha tse kentsoeng li fuoe lintlha tse 15A/32V e 'ngoe le e 'ngoe.
- Li-fuse tse hlahisoang ke 3A/32V.
Lintlha tsa ACMS12CB PTC:
- Li-PTC tsa mantlha li fuoe lintlha tse 9A e 'ngoe le e 'ngoe.
- Li-PTC tse hlahisoang li fuoe lintlha tse 2.5A.
Lipontšo tsa LED:
- Blue LED e bonts'a hore ho hakolloa ha FACP ho qalile.
- Motho ka mong voltage LED e bontša 12VDC (Green) kapa 24VDC (Red).
Tikoloho:
- Mocheso o sebetsang: 0ºC ho isa ho 49ºC tikolohong.
- Mongobo: 20 ho isa ho 93%, e sa fokotseng.
Mechini:
- Litekanyo tsa Boto (W x L x H kakanyo): 7.3" x 4.1" x 1.25" (185.4mm x 104.1mm x 31.8mm)
- Boima ba sehlahisoa (hoo e ka bang): 0.7 lb (0.32 kg).
- Boima ba ho romella (hoo e ka bang): 0.95 lb (0.43 kg).
Litaelo tsa ho Kena:
Mekhoa ea lithapo e tla ba ho latela Khoutu ea Naha ea Motlakase NFPA 70/NFPA 72/ ANSI / Khoutu ea Motlakase ea Canada / CAN/ULC-S524/ULC-S527/ULC-S537, le ka likhoutu tsohle tsa lehae le ba boholong ba nang le matla. Sehlahisoa se reretsoe tšebeliso e omileng ea ka tlung feela.
Sheba Taelo ea ho Kenyeletsoa ha Kopano e Nyenyane bakeng sa ho kenya Rev. MS050913.
Ka hloko review:
| Lisebelisoa tsa LED | (leq. 5) | Setšoantšo se Tloaelehileng sa Kopo | (leq. 6) |
| Lethathamo la Boitsebiso ba Terminal | (leq. 5) | Lits'oants'o tsa ho hoka | (maq. 9-10) |
Kemiso:
- Thaba ea ACMS12/ACMS12CB sebakeng seo u se batlang. Ha u kenya ACMS12 / ACMS12CB feela, sebelisa li-spacers tsa basali / basali (ho fanoe). Ha o hlongoa ka boikhethelo ba VR6 voltage regulator, sebelisa li-spacers tsa basali / basali (tse fanoeng) pakeng tsa ACMS12 / ACMS12CB le VR6 (Setšoantšo sa 6, pg. 6).
Hokela ACMS12/ACMS12CB ho li-spacers tse sebelisang 5/16” likurufu tsa hlooho ea pan (e fanoe).
Lihokelo:
- Netefatsa hore li-output jumpers tsohle [OUT1] - [OUT12] li behiloe sebakeng sa OFF (bohareng).
- Connect low lowtagPhepelo ea motlakase ea DC ho liteishene tse tšoailoeng [+ PWR1 –], [+ PWR2 –]
- Beha tlhahiso e 'ngoe le e' ngoe [OUT1] - [OUT12] ho tsamaisa matla a tsoang ho Power Supply 1 kapa 2 (Fig. 1, pg. 3).
Hlokomela: Lekanya tlhahiso voltage pele o kopanya lisebelisoa.
Sena se thusa ho qoba tšenyo e ka bang teng. - Tima motlakase pele o hokela lisebelisoa.
Ts'ebetso:
Bohlokoa: Li-inputs / Outputs le li-switches tsa tsona li arotsoe ka lihlopha (setšoantšo sa 3, leqephe la 4). - Likhetho tsa ho tsoa: ACMS12(CB) e tla fana ka lisebelisoa tsa motlakase tse fihlang ho tse leshome le metso e 'meli (12)
Liphetoho tsa Power tse fetotsoeng:
Hokela sesebediswa se tsamaisoang ho liteminale tse tšoailoeng [- Output1 +] ka [- Output12 +] ka hloko u shebile polarity.
• Bakeng sa tshebetso e hlolehileng-Sireletsehile, letlapa la taolo ya dilaete tsa DIP switjha e ngotsweng [Output] bakeng sa kenyo e tsamaellanang le boemo ba ON (sa feiga. 3, ka ho le letona).
• Bakeng sa Opereishene e hlolehileng, slide sephetho sa taolo, switjha ea DIP e tšoailoe [Output] bakeng sa kenyo e tsamaellanang sebakeng sa OFF (setšoantšo sa 3, ka ho le letona). - Laeta motlakase oa mantlha ka mor'a hore lisebelisoa tsohle li hoketsoe.
Bohlokoa: Li-inputs / Outputs le li-switches tsa tsona li arotsoe ka lihlopha (setšoantšo sa 3, leqephe la 4). - Likhetho tsa ho Kena:
Hlokomela: Haeba ho khaoha ha Alarm ea Mollo ho sa sebelisoe, hokela sehanyetsi sa 10K Ohm ho litheminale tse tšoailoeng [GND le EOL], 'me u hokele jumper ho litheminale tse tšoailoeng [GND, RST].
Ka tloaelo Bula (NO) Kenyo:
Leano la ho kenya letsoho la taolo ea selaete switch ea DIP e tšoailoeng [NO-NC] bakeng sa kenyo e tsamaellanang sebakeng sa OFF (setšoantšo sa 4, ka ho le letona). Hokela mehala ea hau ho litheminale tse tšoailoeng [+ INP1 –] ho [+ INP12 –].
Keletso e Tlwaelehileng (NC):
Leano la taolo ya selaete switch ya DIP e tshwailweng [NO-NC] bakeng sa kenyo e tsamaellanang le boemo ba ON (setšoantšo sa 4, ka ho le letona). Hokela mehala ea hau ho litheminale tse tšoailoeng [+ INP1 –] ho [+ INP12 –].
Bula Kenyelletso ea Sink ea Collector:
Hokela sink e bulehileng ea pokello ea metsi ho theminale e tšoailoeng [+ INP1 –] ho [+ INP12 –].
Metsi (Moqtage) Tlhophiso ea Kenyeletso:
Ho shebella ka hloko polarity, hokela voltage input trigger wires le 10K resistor e fanoeng ho li-terminals tse tšoailoeng [+ INP1 –] ho [+ INP12 –].
Haeba ho sebetsa voltage ho qala ho kenya - beha phetoho e lumellanang ea INP Logic sebakeng sa "ON".
Haeba ho tlosa voltage ho qala ho kenya - seta phetoho e lumellanang ea INP Logic sebakeng sa "OFF".
- Likhetho tsa Sehokelo sa Alarm ea Mollo:
[NC] eo hangata e koetsoeng, eo hangata e bulang [NO] kapa keno ea ho khutlisa polarity ho tsoa ho potoloho ea matšoao ea FACP e tla hlahisa likhetho tse khethiloeng.
Ho nolofalletsa FACP Disconnect bakeng sa logic ea taolo ea li-slide
DIP switjha tšoauoa [FACP] bakeng sa e tsamaellanang sephetho ON (sa feiga. 5, ka ho le letona).
Ho tima FACP Disconnect bakeng sa leano la taolo ea selaete se hlahisoang
DIP switjha e tšoailoeng [FACP] bakeng sa tlhahiso e tsamaellanang OFF (setšoantšo sa 5, ka ho le letona).
Ka tloaelo Bula Kenyo:
Kopanya relay ea hau ea FACP le sehanyetsi sa 10K 'moho le litheminale tse tšoailoeng [GND] le [EOL].
Kenyelletso e Tloaelehileng:
Kopanya relay ea hau ea FACP le sehanyetsi sa 10K ka lethathamo la litheminale tse tšoailoeng [GND] le [EOL].
Sehlomathisi se kenyang sa Potoloho ea Pontšo ea FACP:
Hokela positive (+) le negative (–) ho tloha ho FACP signaling circuit output ho litheminale tse tšoailoeng [+ FACP –]. Hokela FACP EOL ho li-terminals tse tšoailoeng [+ RET –] (polarity e hlalositsoe boemong ba alamo).
Ho Khaolla Alamo ea Mollo e sa Chesang:
Hokela jumper ho litheminale tse tšoailoeng [GND, RST].
Latching Fire Alarm Disconnect:
Hokela setaele sa ho seta botjha ho NO ka tlwaelo e butsweng ho ditheminale tse ngotsweng [GND, RST]. - FACP Dry NC tlhahiso:
Ha daisy-chaining alamo ea Mollo e bontša lipakeng tsa liboto tse peli, hokela [NC & C] ea ACMS12(CB) ea pele ho [GND & EOL] ea ACMS12(CB) e latelang. Beha jumper ea EOL bohareng le lithakhisa tse tlase.
Ha u sebelisa sehlahisoa sena e le NC e omeletseng, beha jumper ea EOL bohareng le lithapo tse ka holimo.
Daisy Chaining Two (2) ACMS12(CB)
Lilaoli tsa Motlakase oa ho fihlella habeli:
Sebelisa 18 AWG kapa terata e kholoanyane ea UL e nang le 1/4” UL Li-terminals tsa khokahanyo tse potlakileng tse kentsoeng vol e nepahetseng.tage/current bakeng sa likhokahano tsohle tsa jumper.
- Hokela sekoti sa pele sa boto ea ACMS12(CB) se tšoailoeng [PWR1 +] ho theminale ea boto ea ACMS12(CB) ea bobeli e tšoailoeng [+ PWR1].
- Hokela sekoti sa pele sa boto ea ACMS12(CB) se tšoailoeng [COM –] ho boto ea bobeli ea ACMS12(CB) e tšoailoeng [PWR1 –].
- Hokela sekoti sa pele sa boto ea ACMS12(CB) se tšoailoeng [PWR2 +] ho theminale ea boto ea ACMS12(CB) ea bobeli e tšoailoeng [+ PWR2].
Tlhahlobo ea LED:
ACMS12 le ACMS12CB Access Power Controller
| LED | ON | TLOA |
| LED 1- LED 12 (Khubelu) | Li-relay li feletsoe ke matla. | Li-relay tse hlahisoang li matlafalitsoe. |
| FACP | Ho kenya FACP (boemo ba alamo). | FACP e tloaelehileng (boemo boo e seng alamo). |
| Sephetho se Setala 1-12 | 12VDC | – |
| Sephetho se Sefubelu 1-12 | 24VDC | – |
Lethathamo la Boitsebiso ba Terminal:
ACMS12 le ACMS12CB Access Power Controller
| Terminal Taba | Mosebetsi/Tlhaloso |
| + PWR1 - | 12 kapa 24 VDC ho tsoa phepelong ea motlakase. |
| + PWR2 - | 12 kapa 24 VDC ho tsoa phepelong ea motlakase kapa 5 kapa 12 VDC ho tsoa ho molaoli oa VR6. |
| + INP1 - ka + INP12 |
Ba leshome le metso e 'meli (12) ba laoloa ka boikemelo Ka tloaelo Open (NO), Ka tloaelo Ho Koetsoe (NC), Open Collector Sink kapa Wet Input Triggers. |
| C, NC | Phatlalatso ea FACP Dry NC kapa khokahanyo ea ka hare ea EOL ho ACMS12 (CB) e latelang. |
| GND, RST | FACP segokanyimmediamentsi sa sebolokigolo latching kapa e seng latching. HA HO se kentsoeng se ommeng. Sehlopha sa 2 se na le matla a fokolang. E tla khutsufatsoa bakeng sa sebopeho sa FACP se sa ts'oanelang kapa Latch FACP reset. |
| GND, EOL | EOL E hlokometseng liteishene tsa ho Kena tsa FACP bakeng sa ts'ebetso ea polarity ea ho khutlisa FACP. Sehlopha sa 2 se na le matla a fokolang. |
| - F, + F, - R, + R | FACP Signaling Circuit Input and Return terminals. Sehlopha sa 2 se na le matla a fokolang. |
| - Output 1 + ka - Sephetho sa 12 + |
Liphetho tse leshome le metso e 'meli (12) tse ka khethoang ka boikemelo tse laoloang (Fail-Safe kapa Fail-Sireletsehile). |
Setšoantšo se Tloaelehileng sa Tšebeliso:
Kenyeletso/Output Voltage Litekanyetso
| Keletso Voltage le Mohloli | Khumo Voltage Tekanyetso |
| 5VDC (Ho tloha ho VR6 regulator) | 5VDC |
| 12V (ho tloha ho VR6 regulator) | 12VDC |
| 12VDC (ho tloha phepelong ea matla a kantle) | 11.7-12VDC |
| 24VDC (ho tloha phepelong ea matla a kantle) | 23.7-24VDC |
Sephetho se Phahameng sa Lisebelisoa tsa Matla a Altronix:
| Phepelo ea Matla e thathamisitsoeng ka UL kapa e Tsebahalang | Khumo Voltage Setting | Max. Output Current |
| Tlhaloso: AL400ULXB2 / eFlow4NB | 12VDC kapa 24VDC | 4A |
| Tlhaloso: AL600ULXB / eFlow6NB | 12VDC kapa 24VDC | 6A |
| Tlhaloso: AL1012ULXB / eFlow102NB | 12VDC | 10A |
| Tlhaloso: AL1024ULXB2 / eFlow104NB | 24VDC | 10A |
| VR6 | 5VDC kapa 12VDC | 6A |
VR6 - Moqtage Regulator
Fetileview:
VR6 matlatage regulator e fetola tlhahiso ea 24VDC hore e be tlhahiso e laoloang ea 5VDC kapa 12VDC. E etselitsoe ho sebetsa le ACMS12(CB) ka ho lumella ho beha Access Power Controller ka kotloloho holim'a VR6 ho boloka sebaka se koaletsoeng le ho nolofatsa likhokahano. Sheba Tataiso ea Tlhophiso ea VR6 Rev. 050517.
Litlhaloso:
Motlakase / Sephetho:
- Kenyelletso: 24VDC @ 1.75A – Sephetho: 5VDC @ 6A.
- Kenyelletso: 24VDC @ 3.5A – Sephetho: 12VDC @ 6A.
Sephetho:
- 5VDC kapa 12VDC e laoloang tlhahiso.
- Lintlha tse hlahisoang ke 6A max.
- Khatello e phahameng.
Lipontšo tsa LED:
- Li-LED tse kenyang le tse hlahisoang.
Motlakase:
- Mocheso o sebetsang: 0ºC ho isa ho 49ºC tikolohong.
- Mongobo: 20 ho isa ho 93%, e sa fokotseng.
Mechini:
- Boima ba sehlahisoa (hoo e ka bang): 0.4 lb (0.18 kg).
- Boima ba ho romella (hoo e ka bang): 0.5 lb (0.23 kg).
Hokela ACMS12(CB) ho VR6:
- Tlamella li-spacers tsa banna / basali (tse fanoeng) ho li-pem tse lumellanang le mohlala oa lesoba bakeng sa VR6 sebakeng seo u se batlang. Sebelisa spacer ea tšepe bakeng sa lesoba le ntseng le phahama ka mokhoa oa linaleli (setšoantšo sa 7a, leqephe la 8).
- Hokela sehokelo sa lipini tse 8 tsa monna ho seketsoana sa 8-pin sa basali holim'a boto ea VR6 (Setšoantšo sa 7, leqephe la 8).
- Tlama li-spacers tsa basali / basali ho li-spacers tsa banna / basali (setšoantšo sa 7, leqephe la 8).
Sebelisa li-spacers tsa tšepe holim'a sekoti se ntseng se phahama ka mokhoa oa linaleli (setšoantšo sa 7a, leqephe la 8). - Lumellanya sehokelo sa banna ba 8-pin le sepokelo sa basali sa ACMS12/ACMS12CB, ebe u hokela boto ho li-spacers u sebelisa 5/16” li-screws tsa hlooho ea pan (setšoantšo sa 7, leqephe la 8).
- Hokela phepelo ea motlakase ea 24VDC ho terminal e tšoailoeng [+ PWR1 -] ea ACMS12/ACMS12CB (Setšoantšo sa 8, leqephe la 7).
- Khetha bophahamo ba modumotage 5VDC kapa 12VDC e sebelisa switch [S1] ho VR6.
- Qetella mehato ea 4-10 (maq. 3-4).
Litšoantšo tsa Hook-Up:
Setšoantšo sa 8 - Daisy e kopanya yuniti e le 'ngoe kapa ho feta tsa ACMS12.
EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. E sa Lateng.
Setšoantšo sa 9 - Daisy e kopanya yuniti e le 'ngoe kapa ho feta tsa ACMS12.
EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. Latching Single Reset.
Setšoantšo sa 10 - Daisy e kopanya yuniti e le 'ngoe kapa ho feta tsa ACMS12.
EOL Jumper [EOL JMP] e lokela ho kenngoa boemong ba EOL. Latching Individual Reset.
Setšoantšo sa 10 - Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo).
E sa Lateng.
Setšoantšo sa 11 - Polarity reversal input ho tloha FACP signaling circuit output (polarity e hlalosoa ka boemo ba alamo).
Latching.
Setšoantšo sa 12 – Ka tlwaelo e kwetsweng trigger e koetsoeng
(Non-Latching).
Setšoantšo sa 13 – Ka tlwaelo e kwetsweng trigger e koetsoeng
(Latching).
Setšoantšo sa 14 - Ka tloaelo Open trigger input
(Non-Latching).
Setšoantšo sa 15 - Ka tloaelo Open trigger input
(Latching).
Lintlha: -
Altronix ha e ikarabelle bakeng sa liphoso leha e le life tsa typographical.
140 58th Street, Brooklyn, New York 11220 USA
mohala: 718-567-8181
fekse: 718-567-9056
websebaka: www.altelengx.com
lengolo-tsoibila: info@altronix.com
Warranty ea bophelo bohle
IIACMS12/ACMS12CB I01V
Tataiso ea ho Kenya Kopano ea ACMS12/CB
Litokomane / Lisebelisoa
 |
Altronix ACMS12 Series Sub Assembly Access Power Controllers [pdf] Tlhophiso Tataiso ACMS12, ACMS12CB, ACMS12 Series Sub Assembly Access Controllers, Sub Assembly Access Power Controllers, Access Power Controllers, Power Controllers |