Chithunzi cha ACMS12
Sub-Assembly
Access Power Controller
Kuyika Guide

ACMS12 Series Sub Assembly Access Power Controllers

Zithunzi Zimaphatikizaponso:
Chithunzi cha ACMS12
- Zotulutsa khumi ndi ziwiri (12) Zotetezedwa ndi Fuse
Chithunzi cha ACMS12CB
- Zotulutsa khumi ndi ziwiri (12) za PTC zotetezedwa

Zathaview:

Altronix ACMS12/ACMS12CB ndi magulu ang'onoang'ono opangidwa kuti azigwiritsidwa ntchito mu Altronix BC300, BC400, Trove1, Trove2 ndi Trove3 enclosures ndi Maximal power unit. Mapangidwe apawiri a Access Power Controller amalola mphamvu kuwongolera kuchokera ku ma voliyumu awiri (2) odziyimira pawokhatage 12 kapena 24VDC Altronix magetsi kwa khumi ndi awiri (12) paokha ankalamulira fusesi (ACMS12) kapena PTC (ACMS12CB) zotuluka zotetezedwa. Zotulutsa zimayatsidwa ndi sinki yotsegulira yotseguka, yomwe nthawi zambiri imatsegulidwa (NO), yomwe nthawi zambiri imatsekedwa (NC) chowotcha chowuma, kapena kutulutsa konyowa kuchokera mu Access Control System, Card Reader, Keypad, Push Button, PIR, etc. ACMS12(CB) mphamvu yanjira kupita ku zida zosiyanasiyana zowongolera zolumikizira kuphatikiza Mag Locks, Kumenya Magetsi, Magnetic Door Holders, ndi zina zotero. Zotulutsa zidzagwira ntchito mu Fail-Safe kapena Fail-Secure modes. FACP Interface imathandizira Emergency Egress, Alarm Monitoring, kapena ingagwiritsidwe ntchito kuyambitsa zida zina zothandizira. Mbali yochotsa alamu yamoto imasankhidwa payekhapayekha pazotsatira zilizonse khumi ndi ziwiri (12). Zolumikizira za spade zimakulolani kuti muzitha kulumikiza mphamvu zama module angapo a ACMS12(CB). Izi zimakupatsani mwayi wogawa mphamvu pazotulutsa zambiri pamakina akuluakulu.

Zofotokozera:

Lowetsani Voltage:

• Kuyika 1: 12 kapena 24VDC Altronix magetsi.
• Kuyika 2: 12 kapena 24VDC Altronix magetsi kapena 5 kapena 12VDC kuchokera ku VR6 Regulator.
• Zolowetsa Panopa:
  ACMS12: 20A yonse
  ACMS12CB: 16A yonse.
• Zolowetsa khumi ndi ziwiri (12) zosankhidwa payekha:
  a) Nthawi zambiri otsegula (NO) zolowetsa (zowuma).
  b) Zolowetsa zotsekedwa (NC) (zowuma).
  c) Tsegulani zolowetsa zokokera.
  d) Kulowetsa Konyowa (5VDC - 24VDC) ndi 10K resistor
  e) Kuphatikizika kulikonse kwa pamwamba.

Zotuluka:

• ACMS12: Zotuluka zotetezedwa ndi fuse zidavotera @ 2.5A pazotulutsa, zopanda mphamvu.
  Zotulutsa zonse 20A max.
  Onani Zolowetsa/Zotulutsa Voltage Mavoti, p. 7.
  ACMS12CB: Zotuluka zotetezedwa za PTC zidavotera @ 2A pazotulutsa, Gulu lachiwiri lopanda mphamvu.
  Zotulutsa zonse 16A max.
  Osapitilira mavoti amagetsi amunthu payekha.
  Onani Zolowetsa/Zotulutsa Voltage Mavoti, p. 7.
  Zonse zomwe zatuluka siziyenera kupitirira max. mavoti apano amagetsi omwe amagwiritsidwa ntchito pazolowetsa zilizonse.
  Onani Kutulutsa Kwakukulu kwa Altronix Power Supplies.
• Zotulutsa mphamvu khumi ndi ziwiri (12) zosankhidwa paokha zoyendetsedwa ndi Fail-Safe kapena Fail-Secure.
• Zotulutsa zapayekha zitha kukhazikitsidwa kuti ZIZIMU pothandizira (chodumpha chotulutsa chakhazikitsidwa pamalo apakati).
• Zotulutsa ndizosankhika kuti zitsatire Mphamvu Zolowetsa 1 kapena Zolowetsa 2. Kutulutsa voltage ya zotulutsa zilizonse ndizofanana ndi voliyumu yoloweratage za zomwe zasankhidwa.
  Onani Zolowetsa/Zotulutsa Voltage Mavoti, p. 7.
• Kuchepetsa kuthamanga.

Chotsani Alamu ya Moto:

• Kulumikizika kwa Alamu ya Moto (kutchingira kapena kusayakira) kumasankhidwa payekhapayekha pazotsatira zilizonse khumi ndi ziwiri (12).
  Zosankha zolowetsa za Alamu yamoto:
  a) Nthawi zambiri amatsegula [NO] kapena amatseka [NC] zolumikizira zowuma. Kusintha kwa polarity kuchokera kudera losainira la FACP.
• Kulowetsa kwa FACP WET kudavotera 5-30VDC 7mA.
• Kulowetsa kwa FACP EOL kumafuna 10K kutha kwa mzere wotsutsa.
• FACP linanena bungwe relay [NC]:
  Mwina FACP youma NC kutulutsa kapena
  Kulumikizana kwa EOL kwamkati ku ACMS12(CB) yotsatira.

Mavoti a ACMS12 Fuse:

• Ma fuse olowera kwambiri adavotera 15A/32V iliyonse.
• Ma fuse otulutsa adavotera 3A/32V.

Mavoti a ACMS12CB PTC:

• Zowonjezera zazikulu za PTC zimavotera 9A iliyonse.
• Ma PTC otuluka adavotera 2.5A.

Zizindikiro za LED:

• Blue LED ikuwonetsa kuti kulumikizidwa kwa FACP kwayambika.
• Munthu payekha voltage LED imasonyeza 12VDC (Green) kapena 24VDC (Yofiira).

Zachilengedwe:

• Kutentha kwa ntchito: 0ºC mpaka 49ºC mozungulira.
• Chinyezi: 20 mpaka 93%, osasunthika.

Zimango:

• Makulidwe a Board (W x L x H pafupifupi): 7.3" x 4.1" x 1.25" (185.4mm x 104.1mm x 31.8mm)
• Kulemera kwa katundu (pafupifupi.): 0.7 lb (0.32kg).
• Kulemera kwa kutumiza (pafupifupi.): 0.95 lb (0.43kg).

Malangizo oyika:

Njira zama waya zizikhala molingana ndi National Electrical Code NFPA 70/NFPA 72/ ANSI / Canada Electrical Code / CAN/ULC-S524/ULC-S527/ULC-S537, komanso ma code onse amderali ndi maboma omwe ali ndi ulamuliro. Mankhwala cholinga m'nyumba youma ntchito kokha.
Onani Maupangiri Oyika Magawo a Sub-Assembly pakuyika Rev. MS050913.
Mosamala review:

LED Diagnostics	(tsamba 5)	Chithunzi Choyimira Ntchito	(tsamba 6)
Terminal Identification Table	(tsamba 5)	Zithunzi za Hook-up	( tsa. 9-10 )

Kuyika:

1. Phiri la ACMS12/ACMS12CB pamalo omwe mukufuna / mpanda. Mukayika ACMS12/ACMS12CB yokha, gwiritsani ntchito spacers zazimayi / zazikazi (zoperekedwa). Mukakwera ndi VR6 voltage regulator, gwiritsani ntchito spacers akazi / akazi (operekedwa) pakati pa ACMS12 / ACMS12CB ndi VR6 (Mkuyu 6, p. 6).
   Gwirizanitsani ACMS12/ACMS12CB ku spacers pogwiritsa ntchito 5/16 ″ zomangira zapamutu (zoperekedwa).
   Kulumikizana:
   
2. Onetsetsani kuti zodumphira zonse zotulutsa [OUT1] - [OUT12] zayikidwa pa OFF (pakati).
3. Gwirizanitsani voltagMphamvu zamagetsi za e DC zolembedwa [+ PWR1 -], [+ PWR2 -]
4. Khazikitsani zotsatira zilizonse [OUT1] - [OUT12] kuti muyendetse mphamvu kuchokera ku Power Supply 1 kapena 2 (mkuyu 1, p. 3).Zindikirani: Yesani zotuluka voltage pamaso kulumikiza zipangizo.
   Izi zimathandiza kupewa kuwonongeka komwe kungachitike.
5. Zimitsani magetsi musanalumikize zida.
   Zochita:
   Zofunika: Zolowetsa / Zotulutsa ndi masinthidwe awo ali m'magulu (mkuyu 3, p. 4).
6. Zosankha zotulutsa: ACMS12(CB) ipereka mphamvu zosinthira khumi ndi ziwiri (12)
   Kusintha kwa Power outputs:
   Lumikizani cholowetsa cha chipangizo chomwe chikugwiritsidwa ntchito ku ma terminals olembedwa [- Output1 +] kudzera pa [- Output12 +] poyang'anitsitsa polarity.
   • Pantchito ya Fail-Safe slide output control logic switch ya DIP yolembedwa kuti [Output] kuti mulowe mu malo a ON (mkuyu 3, kumanja).
   • Pantchito Yolephera-Kutetezedwa silaidi yowongolera mawu a DIP olembedwa [Zotulutsa] kuti alowe molingana ndi malo OFF (mkuyu 3, kumanja).
7. Yatsani mphamvu yayikulu zida zonse zikalumikizidwa.
   Zofunika: Zolowetsa / Zotulutsa ndi masinthidwe awo ali m'magulu (mkuyu 3, p. 4).
8. Zosankha Zoyambitsa:
   Zindikirani: Ngati kulumikizidwa kwa Alamu ya Moto sikunagwiritsidwe ntchito, lumikizani chopinga cha 10K Ohm ku matheminali olembedwa [GND ndi EOL], ndipo mulumikize cholumphira ku matheminali olembedwa [GND, RST].
   Nthawi zambiri Zolowetsa Zotsegula (NO):
   Sinthani mawu a DIP olowetsamo mawu oti [NO-NC] kuti mulowe nawo pa OFF (Mkuyu 4, kumanja). Lumikizani mawaya anu kumaterminal olembedwa [+ INP1 –] ku [+ INP12 –].
   Zolowetsa Nthawi Zonse (NC):
   Sinthani mawu olowera pazithunzi za DIP zolembedwa [NO-NC] kuti mulowe nawo pa ON (mkuyu 4, kumanja). Lumikizani mawaya anu kumaterminal olembedwa [+ INP1 –] ku [+ INP12 –].
   Tsegulani Zolowetsa Zosonkhanitsa:
   Lumikizani zolowetsa zotsegulira zolowera ku terminal yolembedwa [+ INP1 –] ku [+ INP12 –].
   Madzi (Voltage) Kusintha Kolowetsa:
   Poyang'anitsitsa polarity, gwirizanitsani voltagmawaya oyambitsa ma e input ndi cholumikizira cha 10K choperekedwa kumatheminali cholembedwa [+ INP1 –] kupita ku [+ INP12 –].
   Ngati kugwiritsa ntchito voltage kuti muyambitse zolowetsa - ikani chosinthira chofananira cha INP Logic kupita pa "ON".
   Ngati kuchotsa voltage kuti muyambitse zolowetsa - ikani kusintha kofananira kwa INP Logic kupita ku "OFF".
   
9. Zosankha za Chiyankhulo cha Alamu ya Moto:
   [NC] yomwe imakhala yotsekedwa, yomwe nthawi zambiri imatsegula [NO] kapena kusintha kwa polarity kuchokera kumagawo osayina a FACP kumayambitsa zotulukapo zosankhidwa.
   Kuti mutsegule FACP Disconnect pamalingaliro owongolera otulutsa
   DIP lophimba chizindikiro [FACP] lolingana linanena bungwe ON (mkuyu 5, kumanja).
   Kuti mulepheretse FACP Disconnect pamalingaliro owongolera a slide
   Kusinthana kwa DIP kwalembedwa [FACP] pazotulutsa zofananira ZIMA (Mkuyu 5, kumanja).
   Nthawi zambiri Zolowetsa Zotsegula:
   Yambani mawaya anu a FACP relay ndi 10K resistor XNUMXK molumikizana ndi ma terminals olembedwa [GND] ndi [EOL].
   Zomwe Zimatsekedwa Nthawi zambiri:
   Yambani mawaya anu a FACP relay ndi 10K resistor mu mndandanda wokhala ndi ma terminals olembedwa [GND] ndi [EOL].
   Choyambitsa cholowera cha FACP Signaling Circuit:
   Lumikizani zabwino (+) ndi zoipa (-) kuchokera ku FACP yotulutsa siginecha kupita ku ma terminals olembedwa [+ FACP -]. Lumikizani FACP EOL ku matheminali olembedwa [+ RET –] (polarity imatchulidwa ngati alamu).
   Ma Alamu Amoto Osayatsidwa:
   Lumikizani cholumphira kumalo otchedwa [GND, RST].
   Kuyimitsa Alamu Yamoto Kutha:
   Lumikizani chosinthira cha NO chomwe chimatsegula chosinthira ku malo olembedwa [GND, RST].
10. FACP Dry NC zotuluka:
    Pamene daisy-chaining Alamu ya Moto imasonyeza pakati pa matabwa awiri, gwirizanitsani [NC & C] ya ACMS12(CB) yoyamba ku [GND & EOL] ya ACMS12(CB) yotsatira. Ikani jumper ya EOL pakati ndi zikhomo zapansi.
    Mukamagwiritsa ntchito linanena bungwe ngati NC youma kukhudzana ikani EOL jumper pakati ndi zikhomo pamwamba.

Daisy Chaining Awiri (2) ACMS12(CB)
Zowongolera Mphamvu za Dual Output Access:
Gwiritsani ntchito mawaya 18 AWG kapena okulirapo a UL Listed okhala ndi 1/4” UL Malo olumikizira mwachangu ozindikirika ovotera mphamvu yoyenera.tage/current pamalumikizidwe onse a jumper.

1. Lumikizani chikwama choyamba cha bolodi cha ACMS12(CB) cholembedwa kuti [PWR1 +] ku terminal yachiwiri ya ACMS12(CB) yolembedwa kuti [+ PWR1].
2. Lumikizani chikwama choyamba cha bolodi cha ACMS12(CB) cholembedwa kuti [COM -] ku terminal yachiwiri ya ACMS12(CB) yolembedwa [PWR1 –].
3. Lumikizani chikwama choyamba cha bolodi cha ACMS12(CB) cholembedwa kuti [PWR2 +] ku terminal yachiwiri ya ACMS12(CB) yolembedwa kuti [+ PWR2].

Kuwunika kwa LED:

ACMS12 ndi ACMS12CB Access Power Controller

LED	ON	ZIZIMA
LED 1- LED 12 (Yofiira)	Kutulutsa kotulutsa mphamvu kopanda mphamvu.	zotulutsa zopatsa mphamvu.
FACP	Kulowetsa kwa FACP kuyambika (ma alarm).	FACP yachibadwa (yopanda ma alarm).
Zobiriwira Zobiriwira 1-12	12VDC	–
Kutulutsa Kofiira 1-12	24VDC	–

Table Identity Table:
ACMS12 ndi ACMS12CB Access Power Controller

Mbiri ya Terminal	Ntchito/Kufotokozera
+ PWR1 -	12 kapena 24 VDC kuchokera kumagetsi.
+ PWR2 -	12 kapena 24 VDC kuchokera kumagetsi kapena 5 kapena 12 VDC kuchokera ku VR6 regulator.
+ INP1 - kudzera + INP12 -	Khumi ndi ziwiri (12) zodziyimira pawokha Zotsegula Pazonse (NO), Zomwe Zimatsekedwa (NC), Open Collector Sink kapena Wet Input Triggers.
C, NC	FACP Dry NC zotulutsa kapena kulumikizana kwa EOL kwamkati kupita ku ACMS12(CB).
GND, RST	FACP mawonekedwe latching kapena osawotchera. PALIBE mawu owuma. Class 2 alibe mphamvu. Kufupikitsidwa kwa mawonekedwe osagwirizana ndi FACP kapena kukhazikitsanso Latch FACP.
GND, EOL	EOL Supervised FACP Input terminals for polarity reversal FACP function. Class 2 alibe mphamvu.
- F, + F, - R, + R	FACP Signaling Circuit Inpuit and Return terminals. Class 2 alibe mphamvu.
- Kutulutsa 1 + kudzera - Zotulutsa 12 +	Zotuluka khumi ndi ziwiri (12) zosankhidwa paokha (Fail-Safe kapena Fail-Secure).

Chithunzi chodziwika bwino cha ntchito:

Zolowetsa/Zotulutsa Voltagndi Mavoti

Lowetsani Voltage ndi Source	Kutulutsa Voltage Mavoti
5VDC (Kuchokera ku VR6 regulator)	5VDC
12V (kuchokera ku VR6 regulator)	12VDC
12VDC (kuchokera kunja magetsi)	11.7-12 VDC
24VDC (kuchokera kunja magetsi)	23.7-24 VDC

Kutulutsa Kwamphamvu Kwambiri kwa Altronix Power Supplies:

UL Yolembedwa Kapena Yodziwika Yopereka Mphamvu	Kutulutsa Voltagndi Kukhazikitsa	Max. Zotulutsa Panopa
Chithunzi cha AL400ULXB2/eFlow4NB	12VDC kapena 24VDC	4A
Chithunzi cha AL600ULXB / eFlow6NB	12VDC kapena 24VDC	6A
Chithunzi cha AL1012ULXB / eFlow102NB	12VDC	10A
Chithunzi cha AL1024ULXB2/eFlow104NB	24VDC	10A
Chithunzi cha VR6	5VDC kapena 12VDC	6A

VR6 - Voltage Woyang'anira

Zathaview:
VR6 gawotage regulator amasintha cholowetsa cha 24VDC kukhala chowongolera cha 5VDC kapena 12VDC. Idapangidwa makamaka kuti igwire ntchito ndi ACMS12(CB) polola kuyika Access Power Controller molunjika pamwamba pa VR6 kuti isunge malo otsekera komanso kusavuta kulumikizana. Onani VR6 Installation Guide Rev. 050517.

Zofotokozera:

Mphamvu / Zotulutsa:

• Zolowetsa: 24VDC @ 1.75A – Zotulutsa: 5VDC @ 6A.
• Zolowetsa: 24VDC @ 3.5A – Zotulutsa: 12VDC @ 6A.

Zotulutsa:

• 5VDC kapena 12VDC yoyendetsedwa bwino.
• Zotulutsa 6A max.
• Kuchepetsa kuthamanga.

Zizindikiro za LED:

• Kuyika ndi kutulutsa ma LED.

Zamagetsi:

• Kutentha kwa ntchito: 0ºC mpaka 49ºC mozungulira.
• Chinyezi: 20 mpaka 93%, osasunthika.

Zimango:

• Kulemera kwa katundu (pafupifupi.): 0.4 lb (0.18kg).
• Kulemera kwa kutumiza (pafupifupi.): 0.5 lb (0.23kg).

Kulumikiza ACMS12(CB) ku VR6:

1. Mangirirani zida zachimuna/zachikazi (zoperekedwa) ku pems zomwe zimagwirizana ndi bowo la VR6 pamalo omwe mukufuna. Gwiritsani ntchito spacer yachitsulo pabowo lokwera ndi nyenyezi (mkuyu 7a, p. 8).
2. Pulagini cholumikizira chachimuna cha pini 8 ku chotengera chachikazi cha mapini 8 pa bolodi la VR6 (mkuyu 7, tsamba 8).
3. Limbikitsani ma spacers achikazi / achikazi ku spacers amuna / akazi (mkuyu 7, pg. 8).
   Gwiritsani ntchito zida zachitsulo pamwamba pa dzenje lokwera ndi chitsanzo cha nyenyezi (mkuyu 7a, p. 8).
4. Gwirizanitsani cholumikizira chachimuna cha 8-pini ndi chotengera chachikazi cha ACMS12/ACMS12CB, kenaka mugwirizanitse bolodi ku spacers pogwiritsa ntchito zomangira zapamutu za 5/16 (mkuyu 7, p. 8).
5. Lumikizani magetsi a 24VDC ku terminal yolembedwa [+ PWR1 -] ya ACMS12/ACMS12CB (mkuyu 8, p. 7).
6. Sankhani voltage 5VDC kapena 12VDC pogwiritsa ntchito switch [S1] pa VR6.
7. Malizitsani masitepe 4-10 (masamba 3-4).

Zithunzi za Hook-Up:

Chithunzi 8 - Daisy-chaining imodzi kapena zingapo za ACMS12.
EOL Jumper [EOL JMP] iyenera kukhazikitsidwa pamalo a EOL. Osa Latching.Chithunzi 9 - Daisy-chaining imodzi kapena zingapo za ACMS12.
EOL Jumper [EOL JMP] iyenera kukhazikitsidwa pamalo a EOL. Kuyanjanitsa Single Reset.Chithunzi 10 - Daisy akumanga mayunitsi amodzi kapena angapo a ACMS12.
EOL Jumper [EOL JMP] iyenera kukhazikitsidwa pamalo a EOL. Latching Individual Reset.Chithunzi 10 - Polarity reversal input kuchokera ku FACP signing circuit output (polarity imatchulidwa mu alarm condition).
Osa Latching.Chithunzi 11 - Polarity reversal input kuchokera ku FACP signing circuit output (polarity imatchulidwa mu alamu).
Latching.Chithunzi 12 - Nthawi zambiri Zoyambitsa zotsekera zotsekedwa
(Wosagwetsa).Chithunzi 13 - Nthawi zambiri Zoyambitsa zotsekera zotsekedwa
(Latching).Chithunzi 14 - Nthawi zambiri Open choyambitsa cholowetsa
(Wosagwetsa).Chithunzi 15 - Nthawi zambiri Open choyambitsa cholowetsa
(Latching).Ndemanga: -

Altronix siwoyambitsa zolakwika zilizonse za typographical.
140 58th Street, Brooklyn, New York 11220 USA
foni: 718-567-8181
fax: 718-567-9056
webtsamba: www.kalit.com
imelo: info@altronix.com
Chitsimikizo cha moyo wonse
IIACMS12/ACMS12CB I01VACMS12/CB Sub-Assembly Installation Guide

Zolemba / Zothandizira

Altronix ACMS12 Series Sub Assembly Access Power Controllers [pdf] Kukhazikitsa Guide ACMS12, ACMS12CB, ACMS12 Series Sub Assembly Access Power Controllers, Sub Assembly Access Power Controllers, Access Power Controllers, Power Controllers

Maumboni

• Buku Logwiritsa Ntchito