TECH VANODZORA EU-LX WiFi Floor Strip Controller

Mifananidzo nemadhayagiramu ndezvekuenzanisira chete. Mugadziri ane kodzero yekuunza dzimwe shanduko.

KUchengetedzwa

Usati washandisa chigadzirwa kekutanga mushandisi anofanira kuverenga mitemo inotevera zvakanyatsonaka. Kusateerera mitemo iri mubhuku rino kunogona kukonzera kukuvara kwemunhu kana kukuvara kwemutongi. Bhuku remushandisi rinofanirwa kuchengetwa munzvimbo yakachengetedzeka kuti riwedzere kutariswa. Kuti udzivise tsaona uye zvikanganiso, zvinofanirwa kuve nechokwadi kuti munhu wese anoshandisa mudziyo akazvijaira nemusimboti wekushanda pamwe nekuchengetedza mabasa emutongi. Kana mudziyo uchizoiswa mune imwe nzvimbo, ita shuwa kuti bhuku remushandisi rakachengetwa nemudziyo kuitira kuti chero angangoita mushandisi awane ruzivo rwakakosha nezve mudziyo. Mugadziri haagamuchire mutoro kune chero kukuvara kana kukuvara kunokonzerwa nekuregeredza; saka, vashandisi vanosungirwa kutora matanho ekuchengetedza anodiwa akanyorwa mubhuku rino kuchengetedza hupenyu hwavo nemidziyo.

YAMBIRO 

• Yakakwira voltage! Ita shuwa kuti regulator yakabviswa kubva kune mains isati yaita chero zviitiko zvinosanganisira magetsi emagetsi (plugging tambo, kuisa mudziyo nezvimwewo)
• Chigadzirwa chacho chinofanira kuiswa nemunhu ane ruzivo rwemagetsi.
• Usati watanga mutongi, mushandisi anofanirwa kuyera pasi kuramba kwemagetsi emagetsi pamwe nekudzivirira kwekudzivirira kwetambo.
• Iyo regulator haifanirwe kushandiswa nevana.

YAMBIRO 

• Mudziyo unogona kukuvara kana ukarohwa nemheni. Ita shuwa kuti plug yakadzimwa kubva pamagetsi panguva yedutu.
• Chero kushandiswa kunze kwekutsanangurwa nemugadziri kunorambidzwa.
• Pamberi uye panguva yekupisa, mutongi anofanira kuongororwa mamiriro etambo dzayo. Mushandisi anofanirawo kutarisa kana controller yakanyatsoiswa uye kuichenesa kana ine guruva kana tsvina.

Shanduko mune zvigadzirwa zvinotsanangurwa mubhuku rekushandisa zvinogona kunge zvakaunzwa mushure mekupedzwa kwayo muna Gumiguru 14th 2022. Mugadziri anochengeta kodzero yekuunza shanduko kune chimiro kana mavara. Mifananidzo yacho inogona kusanganisira mimwe michina. Tekinoroji yekudhinda inogona kukonzera kusiyana kwemavara anoratidzwa. Kutarisira zvakatipoteredza ndizvo zvatinokoshesa. Kuziva nezve chokwadi chekuti isu tinogadzira zvigadzirwa zvemagetsi zvinotisungisa kurasa zvinhu zvakashandiswa uye zvigadzirwa zvemagetsi nenzira yakachengeteka kune zvakasikwa. Nekuda kweizvozvo, kambani yakagamuchira nhamba yekunyoresa yakapihwa naMain Inspector weEvironment Protection. Mucherechedzo webhini remarara pane chigadzirwa zvinoreva kuti chigadzirwa hachifanire kukandwa kunze kumabhini emarara akajairika. Nekuparadzanisa marara akagadzirirwa kushandiswa patsva, tinobatsira kuchengetedza zvakatipoteredza. Ibasa remushandisi kuendesa tsvina yemagetsi neyemagetsi kunzvimbo yakasarudzwa yekuunganidza kuti idzokororwe tsvina inogadzirwa kubva mumagetsi nemagetsi.

SYSTEM DESCRIPTION

Iyo EU-LX WiFi controller chimwe chikamu chekudziya/kutonhora kudzora sisitimu inogonesa kuwedzera kwekutonga kweiyo iripo yekumisikidza inopisa nekuunzwa kwenzvimbo yekupisa. Basa rekutanga nderekuchengetedza tembiricha yakatarwa munzvimbo yega yega. EU- LX WiFi chishandiso icho, pamwe chete nemidziyo yese yekutenderera, senge ma sensors emukamuri, makamuri ekudzora, pasi sensors, ekunze sensor, mahwindo sensors, uye thermostatic actuators, inoumba iyo yese yakabatanidzwa system.

Nekuda kwesoftware yayo yakakura, iyo EU-LX WiFi controller inogona kuita akati wandei mabasa:

• tsigiro yeEU-R-12b, EU-R-12s, EU-F-12b uye EU-RX cable regulators
• kudzora mawire regulators: EU-R-8X, EU-R-8b, EU-R-8b Plus, EU-R-8s Plus, EU-F-8z kana sensors: EU-C-8r, EU-C-mini, EU-CL-mini
• tsigiro yepasi tembiricha sensors
• tsigiro yekunze sensors uye mamiriro ekunze
• Tsigiro yeasina waya hwindo sensors (kusvika 6 pcs panharaunda)
• kugona kudzora STT-868, STT-869 kana EU-GX isina waya actuators (6 pcs panharaunda)
• mukana wekushanda thermoelectric actuators
• mukana wekushandisa valve yekusanganisa - mushure mekubatanidza EU-i-1, EU-i-1m valve module
• kutonga kwemudziyo wekudziya kana kutonhora kuburikidza nekukwanisa-kusununguka kuonana
• imwe 230V inobuda kupomba
• mukana wekuseta yega yega inoshanda hurongwa kune yega zone
• mukana wekuvandudza software kuburikidza ne USB port.

KUPINDA SEI

Iyo EU-LX WiFi controller inofanirwa kuiswa chete nemunhu anonyatso kwanisa.

YAMBIRO
Kana mugadziri wepombi achida switch huru yekunze, fiyuzi yemagetsi kana imwe yakasara ikozvino mudziyo inosarudzira mafambiro akamonyoroka zvinokurudzirwa kusabatanidza pombi zvakanangana nekubuda kwekutonga kwepombi. Kuti udzivise kukuvadza kune chigadziro, imwezve yekuchengetedza dunhu inofanira kushandiswa pakati pemutongi uye pombi. Mugadziri anokurudzira ZP-01 pombi adapta, iyo inofanira kutengwa zvakasiyana.

YAMBIRO
Njodzi yekukuvara kana kufa nekuda kwekuvhunduka kwemagetsi pane mhenyu. Usati washanda pane controller, bvisa magetsi ayo uye uchengetedze kubva kune netsaona switching.

KUCHENJERA
Wiring isiriyo inogona kukanganisa controller.

Mufananidzo unoratidza nzira yekubatanidza nekutaurirana nemidziyo yasara:

Kuiswa kwe electrolytic capacitor
Kuti uderedze chiitiko che tembiricha spikes kuverenga kubva ku zone sensor, 220uF / 25V yakaderera impedance electrolytic capacitor, yakabatana mukufanana netambo ye sensor, inofanira kuiswa. Paunenge uchiisa iyo capacitor, gara uchiteerera zvakanyanya kune polarity yayo. Ivhu rechinhu chakamisikidzwa nemucheka muchena chinodzvanywa mukati chaimo chekona ye sensor yekubatanidza, sezvinoonekwa kubva kumberi kwemutongi, uye inoratidzwa mumifananidzo yakanamatira. Yechipiri terminal ye capacitor inopindirwa mukati meiyo terminal yekuruboshwe kongiri. Takaona kuti mhinduro iyi yakabvisa kukanganisa kwaigona kuitika. Nekudaro, zvakakosha kucherechedza kuti iyo yakakosha musimboti ndeyekuisa nemazvo mawaya kuitira kudzivirira kupindira. Iyo wiring haifanirwe kufambiswa pedyo nenzvimbo dzemagetsi emagetsi, zvisinei, kana mamiriro akadai atoitika, sefa iri muchimiro che capacitor inofanirwa kuiswa.

Kubatana pakati pemutongi nevatongi 

Paunenge uchibatanidza vatongi kune mutongi, gumisa kushanda (shandura jumper munzvimbo ye ON) mumutungamiri uye wekupedzisira wevatongi.

KUTANGA KUTANGA

Kuti mutongi ashande nemazvo, matanho anotevera anofanira kuteverwa kwekutanga-up:

• Danho 1: Batanidza iyo EU-LX WiFi musangano controller nemidziyo yese yaanofanirwa kudzora Kubatanidza waya, bvisa chivharo chemutongi uye wozobatanidza wiring - izvi zvinofanirwa kuitwa sekutsanangurwa pazvibatanidza uye madhayagiramu ari mubhuku.
• Danho rechitatu. Shandura pamagetsi, kutarisa kushanda kwezvishandiso zvakabatana Mushure mekubatanidza zvigadziri zvese, shandura pamagetsi emutongi. Uchishandisa iyo Manual Operation function (Menu → Fitter's Menu → Manual Operation), tarisa kushanda kwechimwe chinhu. Kushandisa the mabhatani, sarudza mudziyo uye wodzvanya bhatani reMENU - mudziyo unofanirwa kutariswa unofanirwa kubatika. Tarisa zvese zvakabatana zvishandiso nenzira iyi.
• Danho rechitatu. Seta nguva yazvino uye zuva Kuseta zuva razvino uye nguva, sarudza Menyu → Zvigadziriso zveMutongi → Zvirongwa zveNguva.

KUCHENJERA
Iyo yazvino nguva inogona kugadziridzwa kubva kunetiweki otomatiki Menyu → Controller marongero → Nguva marongero→ otomatiki.

Danho rechitatu. Gadzira tembiricha sensors, makamuri ekudzora Kuti EU-LX WiFi controller itsigire nzvimbo yakapihwa, inofanirwa kugamuchira ruzivo nezve tembiricha iripo. Nzira iri nyore ndeyekushandisa tembiricha ine waya kana isina waya (eg EU-C-7p, EU-C-mini, EU-CL-mini, EU-C-8r). Nekudaro, kana iwe uchishuvira kukwanisa kushandura kukosha kwetembiricha yakatarwa zvakananga kubva munzvimbo, unogona kushandisa zvigadziriso zvemukamuri, semuenzaniso EU-R-8b, EU-R-8z, EU-R-8b Plus kana vakazvitsaurira: EU- R-12b uye EU-R-12s. Kuti ubatanidze sensor nemutongi, sarudza: Menyu → Menyu yeFitter → Zone Zone… → Sensor yekamuri → Sarudza sensor.

Danho rechitatu. Gadzirisa yasara michina yekushandira iyo EU-LX WiFi controller inogona zvakare kushanda neinotevera zvishandiso:

• EU-i-1, EU-i-1m
• kusanganisa vharafu module EU-i-1, EU-i-1m- mamwe mazita, semuenzaniso EU-MW-1 (6 pcs per controller)

Mushure mekuchinja pane yakavakirwa-mukati Internet module, mushandisi ane sarudzo yekudzora kuisirwa kuburikidza neInternet uchishandisa emodul.pl application. Kuti uwane ruzivo rwekugadzirisa, tarisa kubhuku remayorodhi rakasiyana.

KUCHENJERA
Kana mushandisi achida kushandisa zvishandiso izvi panguva yekushanda, zvinofanirwa kuve zvakabatana uye / kana kunyoreswa.

MAIN SCREEN DESCRIPTION

Kudzora kunoitwa uchishandisa mabhatani ari pasi pechiratidziro.
Controller kuratidza.

1. MENU bhatani - rinopinda mutongi menyu, richisimbisa marongero.
2. bhatani - rinoshandiswa kutarisa mamenu mabasa kana kuderedza kukosha kweakagadziridzwa paramita. Iri bhatani rinoshandurawo maparamita ekushanda pakati penzvimbo.
3. bhatani - rinoshandiswa kutarisa menyu mabasa kana kuwedzera kukosha kweakagadziridzwa paramita. Iri bhatani rinoshandurawo maparamita ekushanda pakati penzvimbo.
4. BUDA bhatani - BUDA kubva kune controller menyu kana kudzima marongero kana kushandura skrini view (zoni, nzvimbo).

Sample skrini - ZONES 

1. Zuva razvino revhiki
2. Kunze kwekushisa
3. Pombi kumhanya
4. Activated inogona-yemahara kuonana
5. Irizvino nguva
6. Ruzivo nezve maitiro ekushandisa / hurongwa munzvimbo yakafanira
7. Simba rechiratidzo uye mamiriro ebhatiri yekamuri sensor ruzivo
8. Preset tembiricha munzvimbo yakapihwa
9. Ikozvino kupisa kwepasi
10. Tembiricha iripo munzvimbo yakapihwa
11. Zone ruzivo. Dijiti inooneka inoreva kamuri sensor yakabatana inopa ruzivo nezve tembiricha yazvino munzvimbo yakatarisana. Kana iyo zone parizvino ichidziya kana kutonhora, zvichienderana nemodhiyo, iyo digit inopenya. Kana alarm ikaitika munzvimbo yakapihwa, mucherechedzo unozoratidzwa pachinzvimbo chedijiti. To view iwozvino anoshanda ma parameter eimwe zone, simbisa nhamba yayo uchishandisa iyo mabhatani.

Sample Screen - ZONE

1. Kunze kwekushisa
2. Mamiriro ebhatiri
3. Irizvino nguva
4. Ikozvino maitiro ekushanda kwenzvimbo yakaratidzwa
5. Kupisa kwekutanga kwenzvimbo yakapihwa
6. Ikozvino tembiricha yenzvimbo yakapihwa
7. Ikozvino kupisa kwepasi
8. Maximum pasi tembiricha
9. Ruzivo rwehuwandu hweakanyoreswa hwindo sensors munzvimbo
10. Ruzivo nezve nhamba yeakanyoreswa actuators munzvimbo
11. Icon yenzvimbo inoratidzwa parizvino
12. Ikozvino humidity level munzvimbo yakapihwa
13. Zone name

MATANGO MABASA

OPERATION MODE 

Iri basa rinogonesa activation yeyakasarudzwa inoshanda mode.

• Normal mode - preset tembiricha zvinoenderana neyakagadzikwa hurongwa
• Holiday mode - tembiricha yakatarwa zvinoenderana nezvirongwa zveiyi modhi
  Menyu → Menyu yeFitter → Nzvimbo → Zone… → Zvirongwa → Tembiricha marongero > Modhi yezororo
• Economy mode - tembiricha yakatarwa zvinoenderana nezvirongwa zveiyi modhi
  Menyu → Menyu yeFitter → Nzvimbo → Zone… → Zvirongwa → Tembiricha marongero > Economy mode
• Comfort mode - tembiricha yakatarwa zvinoenderana nezvirongwa zveiyi modhi
  Menyu → Menyu yeFitter → Nzvimbo → Zone… → Zvirongwa → Tembiricha marongero > Comfort mode

KUCHENJERA

• Kuchinja maitiro kuenda kuzororo, hupfumi uye kunyaradza kuchashanda kune ese mazoni. Izvo zvinongogoneka kugadzirisa iyo setpoint tembiricha yeiyo yakasarudzwa modhi yeimwe zone.
• Mune maitiro ekushanda kunze kwezvakajairwa, hazvigoneke kushandura tembiricha yakatarwa kubva pachiyero chemugadziri wekamuri.

ZONES

On
Kuratidza iyo zone seinoshanda pachiratidziro, nyoresa sensor mairi (ona: Fitter's Menu). Basa racho rinokutendera kuti uvhare nzvimbo uye uvanze ma paramita kubva pachiratidziro chikuru.

Seta tembiricha
Iyo tembiricha yakatarwa munzvimbo inobuda kubva kune zvigadziriso zveimwe nzira yekushanda munzvimbo, kureva chirongwa chevhiki. Zvisinei, zvinokwanisika kudzima purogiramu uye kuisa tembiricha yakasiyana uye nguva yekushisa uku. Mushure menguva ino, tembiricha yakatarwa munzvimbo inozoenderana neyakagadzikwa modhi. Nenguva inoenderera, iyo yakatarwa tembiricha kukosha, pamwe nenguva kusvika pakupera kwayo, inoratidzwa pachiratidziro chikuru.

KUCHENJERA
Kana nguva yetembiricha yakatarwa ikaiswa kuCON, tembiricha iyi ichashanda kwenguva isingaperi (tembiricha isingaperi).

Operation mode
Mushandisi anogona view uye gadzirisa zvigadziriso zvemashandisirwo enzvimbo.

• Yemunharaunda Schedule - Rongedza marongero anongoshanda kune ino zone
• Global Schedule 1-5 - Aya marongero ehurongwa anoshanda kune ese mazoni, kwaanoshanda
• Constant tembiricha (CON) - iri basa rinokutendera iwe kuti uise yakaparadzana seti yekushisa kukosha iyo inozoshanda munzvimbo yakapihwa zvachose, zvisinei nenguva yezuva.
• Nekumisikidza nguva - basa iri rinokutendera kuti uise tembiricha yakaparadzana iyo inongoshanda kwenguva yakati. Mushure menguva ino, tembiricha inozobva kune yaimboshanda modhi (hurongwa kana kugara pasina nguva yakatarwa).

Ronga kugadzirisa

Menyu → Nzvimbo → Zone… → Operating mode → Ronga… → Rongedza

1. Mazuva anoshandiswa marongero ari pamusoro
2. Tembiricha yakaiswa kunze kwezvinhanho zvenguva
3. Seta tembiricha yenguva dzenguva
4. Nguva dzenguva

Kugadzirisa chirongwa:

• Shandisa iyo miseve yekusarudza chikamu chevhiki icho chirongwa chakasetwa chichashanda (1st chikamu chevhiki kana 2nd chikamu chevhiki).
• Shandisa bhatani reMENU kuenda kune yakatarwa tembiricha marongero anozoshanda kunze kwenguva dzenguva - isa nemiseve, simbisa uchishandisa bhatani reMENU.
• Shandisa bhatani reMENU kuenda kune zvigadziriso zvenguva dzenguva uye tembiricha yakatarwa inove inoshanda kune yakatarwa nguva yenguva, isa iyo uchishandisa miseve, simbisa neMENU bhatani.
• Woenderera mberi nekugadzirisa kwemazuva anozopihwa kune 1st kana 2nd chikamu chevhiki - ekushanda mazuva anoratidzwa muchena. Zvirongwa zvinosimbiswa nebhatani reMENU, miseve inofamba pakati pezuva rega rega.

Mushure mekuseta hurongwa hwemazuva ese esvondo, tinya bhatani EXIT uye sarudza iyo Confirm sarudzo nebhatani reMENU.

KUCHENJERA
Mushandisi anogona kuseta matatu akasiyana enguva muchirongwa chakapihwa (nechokwadi chemaminitsi gumi nemashanu).

CONTROLLER SETTINGS

• Zvirongwa zvenguva - nguva iripo uye zuva rinogona kutorwa otomatiki kubva kunetiweki kana Internet module yakabatana uye otomatiki modhi inogoneswa. Izvo zvakare zvinogoneka kuti mushandisi kuseta nguva uye zuva kana iyo otomatiki modhi isingashande nemazvo.
• Zvigadziriso zveScreen - Iri basa rinobvumira mushandisi kugadzirisa chiratidziro.
• Ridza mabhatani - iyi sarudzo inoshandiswa kugonesa ruzha runoperekedza kudzvanya mabhatani.

FITTER'S MENU

Menyu yefitter ndiyo yakanyanya kuoma controller menyu. Pano, mushandisi ane sarudzo yakawanda yemabasa anobvumira kushandiswa kwakanyanya kweunyanzvi hwemutongi.

ZONES
Kuti uvhure nzvimbo pane yekudzora ratidziro, nyoresa / activate sensor imomo uye wobva wamisa nzvimbo yacho.

ROOM SENSOR
Mushandisi anogona kunyoresa / kugonesa chero rudzi rwe sensor: NTC wired, RS kana isina waya.

• Hysteresis - inowedzera kushivirira kwekushisa kwekamuri muhuwandu hwe 0.1 ÷ 5 ° C, apo pane kuwedzera kupisa / kutonhora kunogoneswa.
  Example: Iyo tembiricha yekamuri yakasetwa ndeye 23 ° C Hysteresis iri 1 ° C Sensor yemukamuri ichatanga kuratidza kamuri yekupisa mushure mekunge tembiricha yadonha kusvika 22 ° C.
• Calibration -Kamuri sensor calibration inoitwa panguva yekusangana kana mushure menguva yakareba yekushandiswa kwe sensor kana tembiricha yekamuri inoratidzwa ikatsauka kubva kune chaiyo. Kugadzirisa siyana: kubva -10°C kusvika +10°C nechinhanho che0.1°C.

SET TEMPERATURE
Basa racho rinotsanangurwa muMenu → Zones chikamu.

OPERATION MODE
Basa racho rinotsanangurwa muMenu → Zones chikamu.

ZVINOBUDZWA CONFIGURATION
Iyi sarudzo inodzora zvinobuda: pombi yepasi, inogona-yemahara kuonana uye zvinobuda zve sensors 1-8 (NTC yekudzora tembiricha munzvimbo kana pasi sensor kudzora tembiricha yepasi). Sensor inobuda 1-8 inopihwa kumatunhu 1-8, zvichiteerana. Mhando ye sensor yakasarudzwa pano ichaonekwa nekusarudzika mune sarudzo: Menyu → Menyu yeFitter → Nzvimbo → Nzvimbo… → Sensor yekamuri → Sarudza sensor (yekushisa sensor) uye Menu → Fitter's Menu → Nzvimbo → Nzvimbo… → Floor kudziyisa → Floor sensor. → Sarudza sensor (yepasi sensor). Izvo zvinobuda zveese ma sensors zvinoshandiswa kunyoresa zone newaya. Basa racho rinobvumirawo kudzima pombi uye kubata munzvimbo yakapihwa. Nzvimbo yakadaro, pasinei nekudiwa kwekupisa, haizotora chikamu mukutonga.

SETTINGS

• Kudzora kwemamiriro ekunze - iyo sarudzo yekubatidza / kudzima kutonga kwemamiriro ekunze.

KUCHENJERA
Kudzora kwemamiriro ekunze kunoshanda chete kana muMenu → Fitter's menyu → External sensor, iyo Weather control sarudzo yakatariswa.

• Kupisa - basa rinogonesa / rinomisa basa rekupisa. Iko kune zvakare kusarudzwa kwehurongwa huchave hunoshanda kune iyo zone panguva yekudziya uye yekugadzirisa yeyakasiyana inogara tembiricha.
• Kutonhodza - basa iri rinogonesa/kudzima basa rekutonhodza. Iko kune zvakare kusarudzwa kwehurongwa huchave hunoshanda munharaunda panguva yekutonhodza uye kugadzirisa kweyega yega tembiricha.
• Tembiricha marongero - basa rinoshandiswa kuseta tembiricha kune matatu ekushandisa modes (Holiday mode, Economy mode, Comfort mode).

Optimum kutanga
Optimum kutanga ndeye hungwaru kudziyisa control system. Inogonesa kuenderera mberi kwekutarisa kweiyo yekudziya system uye kushandiswa kweruzivo urwu kuti iite otomatiki kudziya kupisa pamberi penguva inodiwa kuti isvike tembiricha yakatarwa. Iyi sisitimu haidi chero kubatanidzwa kune chikamu chemushandisi uye inonyatsopindura kune chero shanduko inokanganisa kushanda kweiyo yekudziya system. Kana, semuenzanisoampuye, pane shanduko dzakaitwa pakuisirwa uye imba inodziya nekukurumidza, iyo optimum yekutanga sisitimu inozoona shanduko pane inotevera programmed tembiricha shanduko inokonzerwa nehurongwa, uye mukutenderera kunotevera kunonoka kuvhurwa kwekudziya kusvika. nguva yekupedzisira, kuderedza nguva inodiwa kuti usvike kune preset tembiricha.

• yakarongwa nguva yekushandura tembiricha yehupfumi kune yakagadzikana iyo Kubata basa iri kuchaita kuti kana iyo yakarongwa shanduko yetembiricha yakatarwa inokonzerwa nehurongwa inoitika, tembiricha iripo mukamuri ichave pedyo nekukosha kwaidiwa.

KUCHENJERA
Iyo optimum yekutanga basa inoshanda chete mukudziya modhi.

ACTUATORS

• Settings
• SIGMA - basa rinogonesa kudzora kwemagetsi emagetsi actuator. Mushandisi anogona kuseta hudiki uye huwandu hwekuvhurwa kwevhavha - izvi zvinoreva kuti dhigirii rekuvhura nekuvhara kwevhavha haringambopfuuri maitiro aya. Mukuwedzera, mushandisi anogadzirisa Range parameter, iyo inosarudza pakamuri tembiricha iyo valve inotanga kuvhara nekuvhura.

KUCHENJERA
Iyo Sigma basa rinowanikwa chete kune STT-868 kana STT-869 actuators.

Example

• Zone preset tembiricha: 23˚C
• Kuvhura zvishoma: 30%
• Kuvhura kukuru: 90%
• Range: 5˚C
• Hysteresis: 2˚C

Nezvirongwa zviri pamusoro, iyo actuator inotanga kuvhara kana tembiricha munzvimbo yasvika 18 ° C (preset tembiricha inobvisa kukosha kwehuwandu). Iko kuvhurika kudiki kuchaitika kana tembiricha yezone yasvika panzvimbo yakatarwa.
Kana imwe nguva yakatarwa yasvika, tembiricha munzvimbo yacho inotanga kudonha. Kana yasvika 21°C (set tembiricha minus hysteresis value), actuator inotanga kuvhura ichisvika pakuvhurwa kwepamusoro kana tembiricha munharaunda yasvika 18°C.

Dziviriro - Kana basa iri rasarudzwa, mutongi anotarisa tembiricha. Kana tembiricha yakatarwa ikapfuudzwa nenhamba yemadhigirii muRange parameter, ipapo ese ma actuators munzvimbo yakapihwa anovharwa (0% kuvhura). Iri basa rinoshanda chete neSIGMA basa rakagoneswa.

• Emergency mode -Iri basa rinogonesa mushandisi kutsanangura iyo actuator kuvhura iyo inomanikidzwa kana chiitiko che alarm munzvimbo yakapihwa (sensor kutadza, kukanganisa kutaurirana).
• Actuator 1-6 - sarudzo inogonesa mushandisi kunyoresa isina waya actuator. Kuti uite izvi, sarudza Rejisa uye tinya muchidimbu bhatani rekutaurirana pane actuator. Mushure mekubudirira kunyoreswa, rimwe ruzivo rwekuwedzera basa rinoonekwa, uko mushandisi anogona view iyo actuator paramita, semuenzaniso mamiriro ebhatiri, huwandu, nezvimwe. Zvinogonekawo kudzima imwe kana ese actuator panguva imwe chete.

WINDOW SENSOR

Settings

• Pa - basa rinogonesa activation yemahwindo sensors mune yakapihwa zone (window sensor kunyoreswa kunodiwa).
• Kunonoka Nguva -Iri basa rinokutendera kuti uise nguva yekunonoka. Mushure menguva yekumisikidzwa yekunonoka, mutongi mukuru anopindura pakuvhurwa kwehwindo uye anovhara kudziyisa kana kutonhora munzvimbo yakatarisana.
  Example: Nguva yekunonoka yakaiswa kune gumi maminetsi. Kana hwindo ravhurwa, sensor inotumira ruzivo kune mukuru controller nezvekuvhura hwindo. Iyo sensor inosimbisa ikozvino mamiriro ehwindo nguva nenguva. Kana mushure menguva yekunonoka (10 maminetsi) hwindo rinoramba rakavhurika, mutongi mukuru achavhara ma actuators uye kudzima kupisa kwenzvimbo.

KUCHENJERA
Kana iyo nguva yekunonoka yakaiswa ku0, ipapo chiratidzo kune actuators kuvhara chinozoendeswa nekukurumidza.

• Wireless -Sarudzo yekunyoresa mahwindo sensors (1-6 pcs panharaunda). Kuti uite izvi, sarudza Nyoresa uye tinya muchidimbu bhatani rekutaurirana pane sensor. Mushure mekubudirira kunyoreswa, imwe Yekuwedzera Ruzivo basa rinoonekwa, uko mushandisi anogona view iyo sensor paramita, semuenzaniso mamiriro ebhatiri, huwandu, nezvimwe. Zvinogoneka zvakare kudzima yakapihwa sensor kana zvese panguva imwe chete.

FLOOR HEATING

Floor Switch

• Sensor Sarudzo -Iri basa rinoshandiswa kugonesa (waya) kana kunyoresa (isina waya) pasi sensors. Panyaya ye sensor isina waya, inyorese nekuwedzera kudzvanya bhatani rekutaurirana pane sensor.
• Hysteresis - inowedzera kushivirira kwekushisa kwekamuri muhuwandu hwe 0.1 ÷ 5 ° C, iyo iyo inowedzera kupisa / kutonhora inogoneswa.

Example:
Iyo yakanyanya tembiricha yepasi ndeye 45 ° C Hysteresis ndeye 2 ° C Mutongi anozodzima kubata mushure mekupfuura 45 ° C pa sensor pasi. Kana tembiricha ikatanga kudonha, iyo yekubata inodzoserwa kumashure zvakare mushure mekunge tembiricha pafloor sensor inodonha kusvika 43 C (kunze kwekunge tembiricha yekamuri yasvika).

• Calibration -Floor sensor calibration inoitwa panguva yekusangana kana mushure menguva yakareba yekushandiswa kwe sensor kana tembiricha yepasi inoratidzwa ichitsauka kubva kune chaiyo. Kugadzirisa siyana: kubva -10°C kusvika +10°C nechinhanho che0.1°C.

KUCHENJERA
Iyo sensor yepasi haina kushandiswa panguva yekutonhora mode.

Operation mode

• Kudzima -Kusarudza iyi sarudzo kunodzima iyo yekudziya yepasi modhi, kureva Floor Dziviriro kana Comfort Mode haishande.
• Floor protection - Iri basa rinoshandiswa kuchengetedza tembiricha yepasi pazasi peseti yakanyanya tembiricha kuchengetedza sisitimu kubva pakupisa. Kana tembiricha ichikwira kusvika kune yakatarwa yakanyanya tembiricha, kudzoreredza kwenzvimbo kuchadzimwa.
• Comfort mode - Iri basa rinoshandiswa kuchengetedza tembiricha yepasi, kureva kuti mutongi anotarisisa tembiricha iripo. Kana tembiricha yakwira kusvika kune yakanyanya kupisa tembiricha, iyo zone yekudziya inodzimwa kudzivirira sisitimu kubva pakupisa. Kana tembiricha yepasi ichidonha pazasi petembiricha yakaderera, iyo zone reheat inodzoserwa.

Min. tembiricha
Basa rinoshandiswa kuseta tembiricha shoma kudzivirira pasi kubva pakutonhora pasi. Kana tembiricha yepasi ichidonha pazasi petembiricha yakaderera, iyo zone reheat inodzoserwa. Iri basa rinowanikwa chete kana ukasarudza Comfort Mode.

Max. tembiricha
Iyo yakanyanya tembiricha yepasi ndeye tembiricha yepasi pamusoro iyo iyo controller ichadzima kupisa zvisinei nekupisa kwekamuri kwazvino. Basa iri rinodzivirira kuiswa kubva pakupisa.

ZVIMWE ZVAKAWANDA
Basa racho rinokubvumira kubata mamwe mazita. Chokutanga pane zvose, zvakakosha kunyoresa kushamwaridzana kwakadaro (1-6 pcs.). Kuti uite izvi, sarudza iyo Registration sarudzo uye muchidimbu dzvanya bhatani rekutaurirana pane mudziyo, semuenzaniso MW-1.
Mushure mekunyoresa uye nekuchinja pamudziyo, zvinotevera mabasa achaonekwa:

• Ruzivo - ruzivo nezve chimiro, maitiro ekushanda uye renji yekubata inoratidzwa pane controller skrini
• On - sarudzo yekugonesa / kudzima kushanda kwekubata
• Operating mode - mushandisi aripo sarudzo yekumisikidza yakasarudzwa yekubata maitiro maitiro
• Nguva modhi - basa rinobvumira kuseta iyo yekusangana yekushanda nguva yenguva yakatarwa Mushandisi anogona kushandura mamiriro ekuonana nekusarudza/kubvisa iyo Active sarudzo uyezve kuseta Nguva yeiyi modhi.
• Constant mode - basa rinobvumira kuseta iyo yekusangana kuti ishande zvachose. Zvinogoneka kushandura chimiro chekuonana nekusarudza / kusasarudza iyo Active sarudzo
• Relays - iyo yekubata inoshanda zvinoenderana nenzvimbo dzayakagoverwa
• Dehumidification - kana iyo Maximum Humidity yakapfuudzwa munzvimbo yakapihwa, iyi sarudzo inobvumidza iwe kutanga iyo yekuomesa mhepo.
• Rongedza marongero - iro basa rinokutendera iwe kuti uise yakaparadzana yekubata hurongwa hwekuita (zvisinei nemamiriro enzvimbo dzekutonga).

KUCHENJERA
Iyo Dehumidification basa rinoshanda chete muKutonhodza oparesheni modhi.

• Delete - iyi sarudzo inoshandiswa kudzima munhu wakasarudzwa.

MIXING VALVE
Iyo EU-LX WiFi controller inogona kushandisa imwe vharafu uchishandisa valve module (eg i-1m). Iyi valve ine RS kutaurirana, asi inofanirwa kuita kunyoresa, izvo zvinoda kuti iwe utore nhamba yemodule iri kumashure kweimba yayo, kana mune software ruzivo skrini). Mushure mekunyoreswa kwakaringana, zvinokwanisika kuseta yega parameter yeAkawedzera valve.

• Information - basa rinokubvumira view iyo valve parameters mamiriro.
• Register - Mushure mekupinda kodhi kuseri kwevhavha kana muMenu → Ruzivo rweSoftware, unogona kunyoresa vharuvhu nemutongi mukuru.
• Manual mode - mushandisi ane simba rekumisa kushanda kwevhavha, kuzarura / kuvhara valve uye shandura pombi uye kuvhara kuitira kuti uchengetedze kushanda kwakarurama kwezvigadziri.
• Version -Iri basa rinoratidza iyo valve software shanduro nhamba. Ruzivo urwu rwakakosha paunosangana nesevhisi.
• Kubviswa kwevhavha -Iri basa rinoshandiswa kudzima zvachose valve. Basa rinoshandiswa, semuenzanisoample, kana uchibvisa valve kana kutsiva module (zvinozofanira kunyoresazve module nyowani).
• On - sarudzo yekugonesa kana kudzima vharuvhu kwenguva pfupi.
• Valve set tembiricha - iyi parameter inokubvumira kuti uise tembiricha yevhavha.
• Zhizha mode - kuvhura zhizha mode inovhara vharafu kudzivirira kupisa kusingakoshi kweimba. Kana iyo boiler tembiricha yakakwira zvakanyanya (inogonesa bhailer chengetedzo inodiwa), iyo valve inovhurwa mune emergency mode. Iyi modhi haishande muReturn protection mode.
• Calibration -Iri basa rinogona kushandiswa kugadzirisa iyo yakavakirwa-mukati vharafu, semuenzaniso mushure mekushandisa kwenguva refu. Panguva yekuenzanisa, vheji inogadzirirwa panzvimbo yakachengeteka, kureva kuti CH valve uye Return protection type kuti isvike panzvimbo yayo yakazaruka zvakakwana, uye yevhavha yepasi uye Kutonhora kwemhando, kuti idzoke zvakakwana panzvimbo yayo yakavharwa.
• Sitiroko imwe chete -Iyi ndiyo yakanyanya sitiroko imwechete (kuvhura kana kuvhara) iyo valve inogona kuita panguva imwechete-tembiricha sampling. Kana tembiricha iri pedyo nenzvimbo yakatarwa, sitiroko iyi inoverengerwa zvichienderana neiyo Proportional coefficient parameter. Iyo diki iyo unit sitiroko, zvakanyanya kunyanya kudziya tembiricha inogona kusvikwa, asi tembiricha yakatarwa inosvika kwenguva yakareba.
• Kuvhura zvishoma - Parameta inotsanangura kuvhurwa kwevharuvhu kudiki muzana muzana. Iyi parameter inoita kuti vharuvhu irege kuvhurika zvishoma kuti ichengetedze kuyerera kudiki.

KUCHENJERA
Kana tikaisa kuzarura kuduku kwevhavha kusvika ku0% (kuvhara kwakakwana), pombi haigoni kushanda kana valve yakavharwa.

• Nguva yekuvhura -A parameter inotsanangura nguva inotora valve actuator kuvhura vharuvhu kubva pa0% kusvika ku100%. Iyi nguva inofanira kusarudzwa kuti ienderane neiyo yevhavha actuator (sezvinoratidzwa pazita rayo).
• Kuyera kumbomira - Iyi parameter inosarudza kuwanda kwekuyera (kutonga) kwekushisa kwemvura kuzasi kweiyo CH yekuisa valve. Kana iyo sensor inoratidza shanduko yekushisa (kutsauka kubva panzvimbo yakatarwa), ipapo solenoid valve ichazarura kana kuvhara ne preset kukosha kuti idzokere kune yakagadziriswa tembiricha.
• Valve Hysteresis - Iyi sarudzo inoshandiswa kuseta iyo valve setpoint tembiricha hysteresis. Uyu ndiwo mutsauko uripo pakati petembiricha yakagara uye tembiricha iyo vharafu inotanga kuvhara kana kuvhurika.

Example: Tembiricha yevhavha preset: 50°C

• Hysteresis: 2°C
• Kumira kwevharuvhu: 50°C
• Kuvhurwa kwevhavha: 48°C
• Kuvhara kwevhavha: 52°C

Kana tembiricha yakatarwa iri 50 ° C uye hysteresis iri 2 ° C, vharafu inomira munzvimbo imwe kana tembiricha yasvika 50 ° C, kana tembiricha inodonha kusvika 48 ° C, inotanga kuvhurika uye kana yasvika 52. °C, vharuvhu inotanga kuvhara kuitira kudzikisa tembiricha.

• Valve mhando -Iyi sarudzo inogonesa mushandisi kusarudza anotevera marudzi evharuvhu:
• CH vharafu - seta patinoda kudzora tembiricha muC CH tichishandisa sensor valve. Iyo sensor yevhavha ichaiswa zasi kwevhavha yekusanganisa pane pombi yekugovera.
• Floor valve - set apo tinoda kugadzirisa tembiricha pane underfloor heat circuit. Rudzi rwepasi runodzivirira hurongwa hwepasi kubva pakupisa kwakanyanya. Kana rudzi rwevhavha yakagadziriswa seC CH uye yakabatanidzwa kune pasi system, inogona kutungamirira kukuvadza kune pasi system.
• Dzorera kuchengetedzwa - seta patinoshuvira kugadzirisa tembiricha pakudzoka kwekuisirwa kwedu tichishandisa sensor yekudzosera. Kudzoka chete uye boiler sensors inoshanda mumhando iyi yevhavha, uye sensor yevhavha haina kubatana kune controller. Muchigadziro ichi, valve inodzivirira kudzoka kwebhailer kubva pakutonhora kunotonhora sechinhu chinonyanya kukosha, uye kana basa rekudzivirira Bhoiler rakasarudzwa, rinodzivirirawo bhailer kubva pakupisa. Kana vharuvhu yakavharwa (0% yakazaruka), mvura inoyerera chete munharaunda pfupi, nepo kuvhurwa kwakazara kwevhavha (100%) kunoreva kuti pfupi pfupi yakavharwa uye mvura inoyerera kuburikidza nepakati pese inodziya system.

KUCHENJERA
Kana Boiler Dziviriro yadzimwa, CH tembiricha haizokanganisa kuvhurwa kwevhavha. Muzviitiko zvakanyanyisa, bhairi rinogona kupisa, saka zvinokurudzirwa kugadzirisa zvigadziro zvekudzivirira bhodha.
Kune rudzi urwu rwevharuvhu, tarisa kuReturn Protection Screen.

• Kutonhodza - gadzirisa patinenge tichida kugadzirisa kutonhora kwegadziriro yekutonhora (vhavha inovhura apo kutonhora kwakagadzirirwa kwakaderera kudarika kutonhora kwevhavha sensor). Kudzivirirwa kweboiler uye Kudzorera kudzivirira hakushande mumhando iyi yevhavha. Rudzi urwu rwevharuvhu runoshanda kunyangwe inoshanda Zhizha modhi, nepo pombi inoshanda uchishandisa yekuvharira chikumbaridzo. Mukuwedzera, iyi mhando yevhavha ine yakaparadzana yekupisa curve inosanganiswa sebasa reiyo Weather sensor.
• Kuvhura muC calibration - Kana basa iri rikagoneswa, vharuvhu inotanga kuenzanisa kubva pachikamu chekutanga. Iri basa rinongowanikwa chete kana rudzi rwevharuvhu rwakaiswa seCH Valve.
• Kupisa kwepasi - zhizha - Basa iri rinongoonekwa mushure mekusarudza rudzi rwevharuvhu seFloor Valve. Kana basa iri rikagoneswa, vharafu yepasi ichashanda muZhizha Modhi.
• Weather control -Kuti basa remamiriro ekunze rishande, isa sensor yekunze munzvimbo isina kuvharirwa, iyo isingaonekwe nemhepo. Mushure mekuisa uye nekubatanidza iyo sensor, chinja pane iyo Weather control basa mune controller menyu.

KUCHENJERA
Setting iyi haiwanikwe muKutonhodza uye Kudzosa Dziviriro Modes.

Heating curve - iyi ndiyo curve maererano neyakagadzika tembiricha yemutongi inotarwa pahwaro hwekunze kwekunze. Kuti vharuvhu ishande zvakanaka, tembiricha yakatarwa (yakadzika pasi pevharuvhu) inogadzirirwa mana ekunze ekunze tembiricha: -20°C, -10°C, 0°C uye 10°C. Pane yakasarudzika yekudziya curve yeKutonhodza modhi. Yakagadzirirwa kutonhora kwepakati pekunze kwe: 10°C, 20°C, 30°C, 40°C.

Room regulator

• Controller mhando
• Kudzora pasina mutongi wekamuri - Iyi sarudzo inofanira kuongororwa kana tisingadi kuti mutongi wekamuri akanganisa kushanda kwevhavha.
• RS regulator - kuderera - tarisa iyi sarudzo kana valve ichizodzorwa nekamuri regulator yakashongedzerwa neRS kutaurirana. Kana basa iri rikatariswa, controller inoshanda zvinoenderana neLower room temp. parameter.
• RS regulator - chikamu - Kana iyi regulator ikabatidzwa, ikozvino boiler uye tembiricha yevharuvhu inogona viewed. Nebasa iri rakatariswa, mutongi achashanda zvinoenderana neKamuri Temperature Difference uye Setpoint Temperature Shanduko paramita.
• Standard room regulator - iyi sarudzo inotariswa kana vharuvhu ichizodzorwa nembiri-state regulator (isina kugadzirwa neRS kutaurirana). Kana basa iri rikatariswa, mutongi anozoshanda zvinoenderana neKamuri regulator tembiricha yakaderera parameter.
  • Room regulator temp. pasi - Muchigadziro ichi, isa kukosha iyo valve ichadzikisa kupisa kwayo kweseti kana tembiricha yakaiswa mukamuri regulator yasvika (kupisa kwekamuri).

KUCHENJERA
Iyi parameter inoshanda kune iyo Standard kamuri regulator uye RS regulator kuderedza mabasa.

• • Kusiyana kwekushisa kwekamuri - Ichi chigadziro chinogadzirisa shanduko yeyuniti mukushisa kwekamuri yemazuva ano (kusvika kune iri pedyo 0.1 ° C) apo imwe shanduko muhutano hwakagadzirirwa hwevhavha ichaitika.
  • Kuchinja kwekushisa kweseti - Ichi chigadziro chinotarisa kuti madhigirii mangani tembiricha yevharuvhu ichawedzera kana kuderera nekuchinja kweyuniti mukupisa kwekamuri (ona: Musiyano wekushisa kwekamuri). Iri basa rinongoshanda chete neRS room regulator uye rine hukama zvakanyanya neKamuri tembiricha musiyano parameter.

Example: Kusiyana kwekushisa kwekamuri: 0.5°C

• • Shanduko yekushisa kwevhavhavha: 1°C
  • Tembiricha yekuseta valve: 40°C
  • Room regulator set tembiricha: 23°C

Kana kutonhora kwekamuri kuchikwira kusvika ku23.5 ° C (ne 0.5 ° C pamusoro pekushisa kwekamuri yakatarwa), valve inovhara kusvika ku39 ° C preset (ne1 ° C).

KUCHENJERA
Iyo parameter inoshanda kune RS proportional regulator basa.

• Room regulator function - Muchiitiko ichi, zvinodikanwa kuseta kana vharuvhu ichivhara (Kuvhara) kana tembiricha ichadzikira (Kamuri regulator tembiricha yakaderera) kana yapisa.
• Proportionality coefficient - The proportionality coefficient inoshandiswa kugadzirisa kuputika kwevhavha. Iyo iri pedyo neyakagadzirirwa tembiricha, iyo diki sitiroko. Kana iyi coefficient yakakwira, vharuvhu inosvika pakuvhurwa kwakafanana nekukurumidza, asi ichave isina kunyatsojeka. The percenttage yekuvhurwa kweyuniti inoverengerwa uchishandisa inotevera fomula: (seti tembiricha - sensor temp.) x (proportionality coefficient/10)
• Maximum yekushisa kwepasi - Iri basa rinotsanangura tembiricha yepamusoro iyo sensor yevhavha inogona kusvika (kana Floor valve yakasarudzwa). Kana kukosha uku kwasvika, valve inovhara, ichidzima pombi, uye ruzivo pamusoro pekupisa kwepasi rinoonekwa pahwindo guru remutongi.

KUCHENJERA
Izvi zvinongoonekwa chete kana mhando yevharuvhu yakaiswa kuFloor valve.

• Kuvhura nzira - Kana, mushure mekubatanidza vharafu kune controller, zvikaitika kuti yaifanirwa kubatanidzwa kune yakatarisana, hazvifanirwe kushandura mitsara yekugovera, asi zvinokwanisika kushandura nzira yekuvhura yevhavha. nekusarudza nzira yakasarudzwa: Kurudyi kana Kuruboshwe.
• Sensor Selection - Iyi sarudzo inoshanda kune inodzosa sensor uye yekunze sensor uye inobvumidza iwe kuti uone kana iyo yekuwedzera valve yekushanda inofanirwa kufunga nezve Self yevhavha module kana Main sensor (Chete muMuranda Mode).
• CH sensor kusarudzwa - Iyi sarudzo inoshandiswa kune CH sensor uye inokubvumira kuti uone kana basa revhavha yekuwedzera inofanira kufunga nezveSelf yevhavha module kana Main sensor (Chete muvaranda mode).
• Dziviriro yeboiler - Izvi zvinopa dziviriro kubva kune yakawandisa CH tembiricha, uye inoitirwa kudzivirira kuwedzera kune njodzi kweiyo boiler tembiricha. Mushandisi anofanira kutanga kuseta iyo yakanyanya kubvumidzwa boiler tembiricha. Muchiitiko chekukwira kwekushisa kune njodzi, vharuvhu inotanga kuvhurika kuti itonhodze boiler pasi. Mushandisi anoisawo huwandu hunobvumirwa CH tembiricha, mushure meiyo valve ichavhura.

KUCHENJERA
Basa racho harisi kushanda kune Kutonhora uye Floor valve marudzi.

• Dzorera dziviriro -Iri basa rinobvumira kuseta iyo bhailer yekudzivirira kubva kune yakanyanyisa kutonhora mvura inodzoka kubva kudunhu guru, izvo zvinogona kukonzera kuderera kwekushisa kweiyo boiler. Kudzivirirwa kwekudzoka kunoshanda nenzira yekuti kana kutonhora kwakanyanya kuderera, valve inovhara kusvikira pfupi pfupi yebhailer inosvika pakupisa kunodiwa.

KUCHENJERA
Basa racho hariratidzike kurudzi rwevharuvhu Kutonhodza.

Pombi yevharuvhu

• Pombi inoshanda modes - basa rinokutendera kuti usarudze pombi inoshanda modhi:
  • Nguva dzose DZIMA - pombi inodzimwa zvachose uye mutongi anongotonga chete kushanda kwevhavha
  • Inogara IRI PAKA - pombi inomhanya nguva dzese zvisinei nekupisa
  • Pamusoro pechikumbaridzo - pombi inotenderera pamusoro peiyo set switching tembiricha. Kana pombi ichizobatidzwa pamusoro pechikumbaridzo, tembiricha yekuchinjisa pombi yechikumbaridzo inofanirawo kusetwa. Iko kukosha kubva kuCH sensor inotorwa mukufunga.
• Mapombi anochinja tembiricha - Iyi sarudzo inoshanda kune pombi inoshanda pamusoro pechikumbaridzo. Iyo pombi yevharuvhu inobatidza kana iyo boiler sensor inosvika pombi yekuchinja tembiricha.
• Pombi anti-stop - Kana yagoneswa, pombi yevharuvhu inobatidza mazuva gumi ega ega kwemaminetsi maviri. Izvi zvinodzivirira mvura kubva pakusvibisa kuiswa kunze kwemwaka wekupisa.
• Kuvhara pazasi tembiricha chikumbaridzo - Kana basa iri rakaitwa (tarisa Yakagoneswa sarudzo), iyo valve icharamba yakavharwa kusvikira iyo boiler sensor inosvika pombi switching tembiricha.

KUCHENJERA
Kana iyo yekuwedzera valve module i-i-1 modhi, iyo inopesana-inosvibisa mabasa emapombi uye kuvhara pasi pechikumbaridzo inogona kuiswa zvakananga kubva ku-sub-menu yeiyo module.

• Valve pombi yekamuri regulator - Sarudzo iyo iyo regulator yekamuri inodzima pombi kana yapisa.
• Pombi chete - Kana yakagoneswa, mutongi anodzora pombi chete uye vharuvhu haidzoreki.
• External sensor calibration - Iri basa rinoshandiswa kugadzirisa sensor yekunze, inoitwa panguva yekuisa kana mushure mekushandisa kwenguva refu sensor kana iyo inoratidzwa yekunze tembiricha inotsauka kubva kune chaiyo. Mushandisi anotsanangura kukosha kwekugadzirisa kwakashandiswa (kugadziridza huwandu: -10 kusvika +10 ° C).
• Kuvhara kwevhavha - Parameter umo maitiro evhavha mu CH mode inogadziriswa mushure mokunge yadzimwa. Kugonesa iyi sarudzo inovhara vharuvhu uye kudzima kunovhura iyo.
• Valve vhiki nevhiki kutonga - Kudzora kwevhiki kunotendera iwe kuronga kutsauka kweiyo tembiricha yevharuvhu pane mamwe mazuva evhiki panguva dzakatarwa. Matembiricha akatsauka seti ari mukati me +/-10°C.
  Kuti uite kutonga kwevhiki nevhiki, sarudza uye tarisa Mode 1 kana Mode 2. Detailed settings of these modes inogona kuwanikwa muzvikamu zvinotevera zve submenu: Set Mode 1 uye Set Mode 2.

CHERECHEDZAI
Nokuda kwekushanda kwakarurama kwebasa iri, zvakakosha kuisa zuva razvino uye nguva.

MODE 1 - mune iyi modhi, zvinokwanisika kuronga kutsauswa kwetembiricha yakatarwa yezuva rega rega revhiki zvakasiyana. Kuita izvi:

• Sarudza sarudzo: Seta Mode 1
• Sarudza zuva revhiki raunoda kushandura marongero etembiricha
• Shandisa mabhatani kusarudza nguva yaunoda kushandura tembiricha. Simbisa sarudzo nekudzvanya bhatani reMENU
• Sarudzo dzinoonekwa pazasi, sarudza CHANGA nekudzvanya bhatani reMENU kana raratidzwa muchena.
• Zvadaro kuderedza kana kuwedzera tembiricha nemutengo wakasarudzwa uye simbisa.
• Kana iwe uchida kuisa shanduko imwechete zvakare kumaawa akavakidzana, dzvanya bhatani reMENU pane yakasarudzwa, uye mushure mesarudzo yaonekwa pazasi pechidzitiro, sarudza COPY uye kopira marongero kune inotevera kana yapfuura awa uchishandisa iyo. mabhatani. Simbisa marongero nekudzvanya MENU.

Example:

Muchiitiko ichi, kana kutonhora kwakaiswa pavhavha iri 50 ° C, neMuvhuro, kubva ku4 00 kusvika ku7 00 maawa, kutonhora kunoiswa pavhavha kuchawedzera ne5 C, kana kusvika ku55 C; mumaawa kubva pa7 00 kusvika 14 00 ichaderera ne10 C, saka ichava 40 C, nepo pakati pe17 00 ne22 00 ichawedzera kusvika 57 C. MODE 2 - mune iyi mode, zvinokwanisika kuronga kutsauka kwetembiricha zvakadzama kwemazuva ese ekushanda (Muvhuro - Chishanu) uye kwekupera kwevhiki (Mugovera - Svondo). Kuita izvi:

• Sarudza sarudzo: Seta Mode 2
• Sarudza chikamu chevhiki chaunoda kushandura marongero etembiricha
• Iyo imwezve maitiro akafanana neyemuModhi 1

Example:

Muchiitiko ichi, kana kutonhora kwakaiswa pavhavha iri 50 C Muvhuro kusvika Chishanu, kubva ku4 00 kusvika ku7 00, kutonhora pavhavha kuchawedzera ne5 C, kana ku55 C; mumaawa kubva ku7 00 kusvika ku14 00 ichaderera ne10 C, saka ichava 40 C, nepo pakati pe17 00 ne22 00 ichawedzera kusvika ku57 C. Mukupera kwevhiki, kubva ku6 00 kusvika ku9 00 maawa, the tembiricha iri pavharuvhu ichakwira ne5 C, kureva kuti 55 C, uye pakati pe17 00 ne22 00 ichakwira kusvika pa57 C.

• Zvigadziriso zvefekitari - Iyi parameter inokutendera kuti udzokere kune zvigadziriso zvevhavha yakapihwa yakachengetedzwa nemugadziri. Kudzorera zvigadziriso zvefekitari kunoshandura rudzi rwevhavha kune CH valve.

INTERNET MODULE
Iyo Internet module chishandiso chinobvumira kure kure kudzora kwekuisirwa. Mushandisi anogona kudzora mashandiro ezvishandiso zvakasiyana uye kushandura mamwe ma paramita uchishandisa emodul.pl application. Iyo mudziyo ine yakavakirwa-mukati Internet module. Mushure mekuchinja paInternet module uye kusarudza iyo DHCP sarudzo, mutongi anozotora otomatiki maparamita akadai: IP kero, IP mask, Gateway kero uye DNS kero kubva kune yemuno network.

Inodiwa zvigadziriso zvenetiweki
Kuti iyo Internet module ishande nemazvo, inodiwa kuti ubatanidze iyo module kune network ine DHCP server uye yakavhurika port 2000. Kana iyo Internet module yanyatsobatana netiweki, enda kumenu zvigadziriso zvemodule (mune tenzi controller). Kana iyo network isina sevha yeDHCP, iyo Internet module inofanirwa kugadziridzwa nemutungamiriri wayo nekuisa iyo yakakodzera paramita (DHCP, IP Kero, Gateway Kero, Subnet Mask, DNS Kero). Configuration inogona kuitwa ne:

1. Enda kune zvigadziriso menyu yeInternet module.
2. Sarudza "Enabled" sarudzo
3. Wobva watarisa kana iyo "DHCP" sarudzo yakatariswa.
4. Pinda "WIFI Selection"
5. Wobva wasarudza yako WIFI network uye isa password yayo.
6. Mirira kwechinguva (ca. 1min) uye tarisa kana IP kero yakapiwa. Enda ku "IP Kero" tab uye tarisa kana kukosha kwakasiyana pane 0.0.0.0/ -.-.-.- .
   • Kana kukosha kuchiri kuratidza 0.0.0.0 / -.-.-.-.- tarisa zvirongwa zvetiweki kana kubatana kweEthernet pakati peInternet module uye mudziyo.
7. Mushure mekunyatso kugovera IP kero, tinogona kutanga kunyoresa module kuti ibudise iyo kodhi inodiwa kuti ipe iyo kuaccount account.

MUDZIMAI WEMAOKO
Iri basa rinokubvumira kuti udzore kushanda kwemidziyo yega yega. Mushandisi anogona kushandura nemaoko pane chimwe nechimwe chezvishandiso: pombi, inogona-yemahara kuonana uye yega valve actuators. Inokurudzirwa kushandisa manual operation mode, kutarisa kushanda kwakarurama kwezvishandiso zvakabatana pakutanga kwekutanga.

EXTERNAL SENSOR

KUCHENJERA
Iri basa rinowanikwa chete kana sensor yekunze yakanyoreswa muEU-LX WiFi controller.
Iwe unogona kubatanidza yekunze tembiricha sensor kune EU-LX WiFi controller (chibatanidza mune controller- Yekuwedzera sensor 1), iyo inokutendera kuti uchinje pakutonga kwemamiriro ekunze, ne:

• Sensor Sarudzo - Unogona kusarudza ingave NTC wired sensor kana C-8zr isina waya sensor. Wireless sensor inoda kunyoreswa.
• Calibration - Calibration inoitwa pakumisikidzwa kana mushure mekushandisa kwenguva refu sensor kana tembiricha yakayerwa ne sensor inotsauka kubva kune chaiyo tembiricha. Kugadzirisa siyana kunobva -10°C kusvika +10°C nechinhanho che0.1°C.

Panyaya ye sensor isina waya, iyo inotevera parameter ine chekuita nemhando uye nhanho yebhatiri.

KUSVIRA KUMIRA
Basa rekudzivirira ma actuator kuti asabatike panguva dzakatarwa dzenguva.

• Date settings
  • Heating deactivation - Isa zuva richadzimwa kupisa kupisa
  • Heating activation - kuseta zuva iro kupisa kuchashandurwa
• Kudzora kwemamiriro ekunze - Kana iyo yekunze sensor yakabatana, iyo huru skrini inoratidza tembiricha yekunze uye iyo controller menyu icharatidza tembiricha yekunze.
  Basa rinobva kune kunze kwekushisa rinobvumira kutarisa kutaridzika kwekushisa, iyo ichashanda zvichienderana nekupisa kwekushisa. Kana tembiricha yepakati ikapfuura iyo yakataurwa tembiricha, mutongi anodzima kupisa kwenzvimbo umo basa rekutonga kwemamiriro ekunze rinoshanda.
• On - kushandisa kutonga kwemamiriro ekunze, sensor yakasarudzwa inofanira kugoneswa.
• Avhareji yenguva - mushandisi anoisa nguva pahwaro hwekuti tembiricha yekunze ichaverengerwa. Setting range kubva 6 kusvika 24 maawa.
• Temperature threshold - iri ibasa rinodzivirira kubva pakupisa kwakanyanya kwenzvimbo yakapihwa. Iyo zoni inobatidzwa kudzora kwemamiriro ekunze ichavharwa kubva pakupisa kana tembiricha yekunze zuva nezuva ikadarika tembiricha yakatarwa. For example, kana tembiricha ichikwira muchirimo, mutongi anovhara zvisingakoshi kupisa kwekamuri.
• Avhareji yekushisa kwekunze - kukosha kwekushisa kwakaverengerwa pahwaro hweAvhareji yenguva.

ZVINOGONA-KUSIYANA CONTACT
Iyo EU-LX WiFi controller inomisa iyo inogona-yemahara kuonana (mushure mekuverenga pasi nguva yekunonoka) kana chero yenzvimbo isati yasvika pakudziya kwakatarwa (kupisa - kana nzvimbo yacho yadzikiswa, kutonhora - kana tembiricha iri munharaunda yapera. zvakanyanyisa). Iyo controller inodzima kubata kana tembiricha yakatarwa yasvika.

• Kushanda kunonoka - basa rinobvumira mushandisi kuseta nguva yekunonoka yekuchinja pane inogona-yemahara kuonana mushure mekunge tembiricha yadonha pasi petembiricha yakatarwa mune chero yenzvimbo.

PUMP
Iyo EU-LX WiFi controller inodzora kushanda kwepombi - inobatidza pombi (mushure mekuverenga pasi nguva yekunonoka) kana chero yenzvimbo yakadzikiswa uye kana sarudzo yepombi yepasi ichigoneswa munzvimbo yakatarisana. Kana nzvimbo dzese dzadziyirwa (tembiricha yakatarwa yasvika), mutongi anodzima pombi.

• Kushanda kunonoka - basa rinobvumira mushandisi kuisa nguva yekunonoka yekushandura pombi mushure mekunge tembiricha yadonha pasi petembiricha yakatarwa mune chero yenzvimbo. Kunonoka kuchinjisa pombi kunoshandiswa kubvumira valve actuator kuvhura.

KUSVIRA – KUPORORA
Basa racho rinokubvumira kuti usarudze maitiro ekushanda:

• Kupisa - nzvimbo dzose dzinopisa
• Kutonhodza - nzvimbo dzose dzakatonhodzwa
• Otomatiki - mutongi anochinja modhi pakati pekudziya uye kutonhora zvichibva pane maviri-nyika yekuisa.

ANTI-SOP SETTINGS
Basa iri rinomanikidza kushanda kwepombi nemavharuvhu (tarisa sarudzo kutanga), izvo zvinodzivirira sikeri deposits panguva yekusashanda kwenguva refu kwemapombi nemavharuvhu, semuenzaniso kunze kwemwaka wekudziya. Kana basa iri rikagoneswa, pombi nemavharuvhu zvinobatidza kwenguva yakatarwa uye nenguva yakatarwa (semuenzaniso mazuva gumi ega ega kwemaminitsi mashanu).

MAXIMUM HUMIDITY
Kana iyo ikozvino humidity level yakakwira kupfuura yakatarwa humidity yakanyanya, kutonhora kwenzvimbo kuchabviswa.

KUCHENJERA
Iro basa rinongoshanda muKutonhora modhi, chero iyo sensor ine humidity kuyerwa yakanyoreswa munzvimbo.

MUTAURO
Basa racho rinokubvumira kuti uchinje shanduro yemutauro wekutonga.

HEMA PUMP
Dedicated mode yekuisa kushanda nepombi yekupisa, inobvumira kushandiswa kwakanyatsonaka kwekugona kwayo.

• Maitiro ekuchengetedza magetsi - kutara sarudzo ichatanga iyo modhi uye dzimwe sarudzo dzichaonekwa.
• Minimum pause nguva - parameter inodzikamisa nhamba ye compressor switch, iyo inobvumira kuwedzera hupenyu hwe compressor. Pasinei nekudikanwa kwekudziyazve nzvimbo yakapihwa, iyo compressor inotanga chete mushure mekunge nguva yakaverengerwa kubva kumagumo ekutenderera kwekutanga kwebasa kwapera.
• Bypass - sarudzo inodiwa kana pasina buffer, ichipa pombi yekupisa ine simba rakakodzera rekupisa. Inotsamira pakuvhurwa kwakatevedzana kwenzvimbo dzinotevera panguva yega yega yakatarwa.
  • Pombi yepasi - activate/deactivate floor pombi
  • Nguva yekutenderera - nguva iyo nzvimbo yakasarudzwa ichavhurwa.

FACTORY SETTINGS

Basa racho rinokutendera kuti udzoke kune iyo fitter menyu zvigadziriso zvakachengetwa nemugadziri.

SERVICE MENU
Menyu yebasa remutyairi inongowanikwa kune vanhu vane mvumo uye inodzivirirwa nekodhi yekodhi yeTech Sterowniki.

FACTORY SETTINGS
Basa racho rinokubvumira kuti udzoke kune zvigadziro zvemutongi, sezvinotsanangurwa nemuiti.

SOFTWARE VERSION
Kana iyi sarudzo yaitwa, logo yemugadziri ichaonekwa pachiratidziro, pamwe nenhamba yesoftware yekudzora software. Iyo software yekudzokorora inodiwa kana uchibata iyo Tech Sterowniki sevhisi.

ALARM LIST

SOFTWARE ZVIMWE

Kuti uise software nyowani, bvisa mutongi kubva kunetiweki. Isa iyo USB flash drive ine software nyowani mu USB port. Wobva wabatanidza controller kune network uchibata pasi EXIT bhatani. Bata pasi EXIT bhatani kudzamara wanzwa beep imwe chete inomaka kutanga kwesoftware nyowani kurodha. Kana basa rapera, mutongi anozvitangazve.

KUCHENJERA

• Maitiro ekurodha software nyowani kune controller anogona chete kuitwa neanokwanisa installer. Mushure mekushandura software, hazvibviri kudzorera zvirongwa zvekare.
• Usadzima mutongi paunenge uchivandudza software.

TECHNICAL DATA

• AC1 mutoro wechikamu: single-phase, resistive kana zvishoma inductive AC mutoro.
• DC1 mutoro wechikamu: yakananga ikozvino, inopikisa kana kuti inductive zvishoma.

EU KUZIVISA KWEKUTENDERANA

Pano, tinozivisa pasi pebasa redu chete kuti EU-LX WiFi inogadzirwa neTECH STEROWNIKI II Sp. z oo, inotungamirwa muWieprz Biała Droga 31, 34-122 Wieprz, inoenderana neDirective 2014/53/EU yeParamende yeEuropean uye yeKanzuru ya16 Kubvumbi 2014 pakuwiriranisa mitemo yeNyika dzeMatunhu zvine chekuita ne Kuwanikwa pamusika wemidziyo yeredhiyo, Directive 2009/125/EC kumisa hwaro hwekugadzika kwezvinodiwa zveecodesign zvezvigadzirwa zvine chekuita nemagetsi pamwe nemutemo neMINISTRY OF ENTREPRENEURSHIP AND TECHNOLOGY ya24 Chikumi 2019 ichigadzirisa mutemo une chekuita ne izvo zvakakosha zvinodikanwa maererano nekurambidzwa kwekushandiswa kwezvimwe zvinhu zvine ngozi mumagetsi nemidziyo yemagetsi, kuita zvakatemwa Directive (EU) 2017/2102 yeParamende yeEuropean uye yeKanzuru ye15 Mbudzi 2017 inogadzirisa Directive 2011/65 / EU pa kudziviswa kwekushandiswa kwezvimwe zvinhu zvinokuvadza mumagetsi nemagetsi emagetsi (OJ L 305, 21.11.2017, p. 8).
Pakuongorora kutevedza, zviyero zvakaenderana zvakashandiswa:

• PN-EN IEC 60730-2-9 :2019-06 art. 3.1a Kuchengeteka kwekushandisa
• PN-EN IEC 62368-1:2020-11 art. 3.1 Kuchengeteka kwekushandisa
• PN-EN 62479:2011 art. 3.1 Kuchengeteka kwekushandisa
• ETSI EN 301 489-1 V2.2.3 (2019-11) art.3.1b Electromagnetic kugarisana
• ETSI EN 301 489-3 V2.1.1 (2019-03) art.3.1 b Electromagnetic kugarisana
• ETSI EN 301 489-17 V3.2.4 (2020-09) art.3.1b Electromagnetic kugarisana
• ETSI EN 300 328 V2.2.2 (2019-07) art.3.2 Kushandiswa kwakanaka uye kwakabatana kweredhiyo spectrum
• ETSI EN 300 220-2 V3.2.1 (2018-06) art.3.2 Kushandiswa kwakanaka uye kwakabatana kweredhiyo spectrum
• ETSI EN 300 220-1 V3.1.1 (2017-02) art.3.2 Kushandiswa kwakanaka uye kwakabatana kweredhiyo spectrum
• EN IEC 63000:2018 RoHS

Central headquarters
ul. Biata Droga 31, 34-122 Wieprz

Service
ul. Skotnica 120, 32-652 Bulowice

• foni: +48 33 875 93 80
• e-mail: serwis@techsterrowniki.pl
• www.tech-controllers.com

Zvinyorwa / Zvishandiso

TECH VANODZORA EU-LX WiFi Floor Strip Controller [pdf] User Manual EU-LX, EU-LX WiFi Floor Strip Controller, WiFi Floor Strip Controller, Floor Strip Controller, Strip Controller, Controller

References

• User Manual