Owongolera TECH EU-LX WiFi Floor Strip Controller

Zithunzi ndi zojambulazo ndi fanizo lokha. Wopanga ali ndi ufulu wowonetsa zosintha zina.

CHITETEZO

Musanagwiritse ntchito chipangizo kwa nthawi yoyamba wosuta ayenera kuwerenga malamulo otsatirawa mosamala. Kusamvera malamulo omwe ali m'bukuli kungayambitse kuvulala kapena kuwonongeka kwa woyang'anira. Buku la wogwiritsa ntchito liyenera kusungidwa pamalo otetezeka kuti lizigwiritsidwanso ntchito. Pofuna kupewa ngozi ndi zolakwika, ziyenera kutsimikiziridwa kuti munthu aliyense wogwiritsa ntchito chipangizochi adzidziwa bwino ndi mfundo yoyendetsera ntchito komanso ntchito za chitetezo cha woyang'anira. Ngati chipangizocho chiyenera kuikidwa pamalo ena, onetsetsani kuti buku la wogwiritsa ntchito likusungidwa ndi chipangizocho kuti aliyense wogwiritsa ntchito azitha kudziwa zambiri zokhudza chipangizocho. Wopanga savomereza kuvulala kapena kuwonongeka kulikonse chifukwa cha kusasamala; Choncho, ogwiritsa ntchito akuyenera kutenga njira zotetezera zomwe zalembedwa m'bukuli kuti ateteze miyoyo yawo ndi katundu wawo.

CHENJEZO 

• Mkulu voltage! Onetsetsani kuti chowongolera chachotsedwa pa mains musanayambe kuchita chilichonse chokhudza magetsi (kulumikiza zingwe, kukhazikitsa chipangizo ndi zina).
• Chipangizocho chiyenera kukhazikitsidwa ndi katswiri wamagetsi.
• Asanayambe chowongolera, wogwiritsa ntchito ayenera kuyeza kukana kwa ma mota amagetsi komanso kukana kwa zingwe.
• The regulator sayenera kuyendetsedwa ndi ana.

CHENJEZO 

• Chipangizocho chikhoza kuwonongeka ngati chikawombedwa ndi mphezi. Onetsetsani kuti pulagi yachotsedwa pamagetsi pakagwa mphepo yamkuntho.
• Kugwiritsiridwa ntchito kwina kulikonse kusiyana ndi kunenedwa ndi wopanga ndikoletsedwa.
• Nyengo yotentha isanayambe komanso nthawi yotentha, wowongolera amayenera kuyang'aniridwa ngati zingwe zake zili bwanji. Wogwiritsa ntchitoyo ayang'anenso ngati chowongoleracho chakwera bwino ndikuchiyeretsa ngati chafumbi kapena chakuda.

Kusintha kwazinthu zomwe zafotokozedwa m'bukuli mwina zidayambitsidwa pambuyo pomaliza pa Okutobala 14, 2022. Wopangayo ali ndi ufulu wowonetsa zosintha pamapangidwe kapena mitundu. Zithunzizo zingaphatikizepo zida zowonjezera. Ukadaulo wosindikiza ukhoza kupangitsa kusiyana kwamitundu yowonetsedwa. Kusamalira chilengedwe ndi chinthu chofunika kwambiri kwa ife. Kudziwa kuti tikupanga zida zamagetsi kumatikakamiza kutaya zinthu zomwe zagwiritsidwa kale ntchito ndi zida zamagetsi m'njira yotetezedwa ku chilengedwe. Zotsatira zake, kampaniyo yalandira nambala yolembera yoperekedwa ndi Main Inspector of Environmental Protection. Chizindikiro cha nkhokwe ya zinyalala yophatikizika pa chinthu chimatanthauza kuti katunduyo asatayidwe ku nkhokwe za zinyalala wamba. Polekanitsa zinyalala zomwe zimayenera kubwezeretsedwanso, timathandizira kuteteza chilengedwe. Ndi udindo wa wogwiritsa ntchito kusamutsa zinyalala zamagetsi ndi zamagetsi kumalo osankhidwa osonkhanitsira zinyalala zopangidwa kuchokera ku zida zamagetsi ndi zamagetsi.

Dongosolo Kufotokozera

Wolamulira wa EU-LX WiFi ndi gawo la makina owongolera kutentha / kuziziritsa komwe kumathandizira kukulitsa kuwongolera kwa kukhazikitsa komwe kulipo poyambitsa kutentha. Ntchito yayikulu ndikusunga kutentha kokhazikitsidwa kale muzoni iliyonse. EU- LX WiFi ndi chipangizo chomwe, pamodzi ndi zida zonse zotumphukira, monga zowunikira zipinda, zowongolera zipinda, masensa apansi, masensa akunja, masensa a zenera, ndi ma thermostatic actuators, amapanga dongosolo lonse lophatikizika.

Chifukwa cha mapulogalamu ake ambiri, wolamulira wa EU-LX WiFi amatha kugwira ntchito zingapo:

• thandizo la EU-R-12b, EU-R-12s, EU-F-12b ndi EU-RX zowongolera zingwe
• kuwongolera owongolera opanda zingwe: EU-R-8X, EU-R-8b, EU-R-8b Plus, EU-R-8s Plus, EU-F-8z kapena masensa: EU-C-8r, EU-C-mini, EU-CL-mini
• thandizo kwa masensa kutentha pansi
• thandizo kwa masensa akunja ndi kuwongolera nyengo
• kuthandizira kwa masensa opanda zingwe (mpaka ma PC 6 pa zone)
• Kuthekera kowongolera STT-868, STT-869 kapena EU-GX opanda zingwe (ma 6 ma PC pa zone)
• kuthekera kogwiritsa ntchito ma thermoelectric actuators
• kuthekera kogwiritsa ntchito valve yosakaniza - mutatha kulumikiza EU-i-1, EU-i-1m valve module
• Kuwongolera kwa chipangizo chotenthetsera kapena choziziritsa pogwiritsa ntchito kulumikizana kwaulere
• imodzi yotulutsa 230V kuti ipope
• kuthekera kokhazikitsa ndondomeko yogwirira ntchito pagawo lililonse
• kuthekera kosintha pulogalamuyo kudzera padoko la USB.

MMENE MUYANG'ANIRA

EU-LX WiFi controller iyenera kukhazikitsidwa ndi munthu woyenerera bwino.

CHENJEZO
Ngati wopanga mapampu amafuna chosinthira chachikulu chakunja, fuse yamagetsi kapena zida zina zotsalira zapano zosankha mafunde opotoka tikulimbikitsidwa kuti tisalumikizane ndi mapampu molunjika ku zotulutsa zowongolera. Pofuna kupewa kuwononga chipangizocho, dera lowonjezera lachitetezo liyenera kugwiritsidwa ntchito pakati pa owongolera ndi mpope. Wopanga amalimbikitsa chosinthira chopopera cha ZP-01, chomwe chiyenera kugulidwa padera.

CHENJEZO
Kuopsa kwa kuvulala kapena kufa chifukwa cha kugwedezeka kwa magetsi pamalumikizidwe amoyo. Musanagwiritse ntchito chowongolera, chotsani magetsi ake ndikuyiteteza kuti isayatse mwangozi.

CHENJEZO
Mawaya olakwika amatha kuwononga chowongolera.

Chithunzi chowonetsera momwe mungalumikizire ndikulumikizana ndi zida zotsalira:

Kuyika kwa electrolytic capacitor
Pofuna kuchepetsa zochitika za kutentha kwa spikes zomwe zimawerengedwa kuchokera ku zone sensor, 220uF / 25V low impedance electrolytic capacitor, yolumikizidwa mofanana ndi chingwe cha sensor, iyenera kuikidwa. Mukayika capacitor, nthawi zonse samalani kwambiri ndi polarity yake. Pansi pa chinthu chomwe chili ndi mzere woyera chimakhomeredwa kumtunda wakumanja kwa cholumikizira cha sensor, monga chikuwonekera kutsogolo kwa wowongolera, ndikuwonetseredwa pazithunzi zomwe zalumikizidwa. The terminal yachiwiri ya capacitor imakhomeredwa mu terminal ya cholumikizira chakumanzere. Tinapeza kuti yankho ili lathetsa zosokoneza zomwe zingakhalepo. Komabe, ndikofunikira kudziwa kuti mfundo yayikulu ndikuyika mawaya molondola kuti mupewe kusokoneza. Mawaya sayenera kuyendetsedwa pafupi ndi magwero amagetsi amagetsi, komabe, ngati izi zachitika kale, zosefera zamtundu wa capacitor ziyenera kuyikidwa.

Kugwirizana pakati pa owongolera ndi owongolera 

Mukagwirizanitsa olamulira kwa wolamulira, thetsani ntchitoyo (kusintha jumper mu malo a ON) mu olamulira ndi otsiriza a olamulira.

CHOYAMBA CHOYAMBA

Kuti wowongolera azigwira bwino ntchito, njira zotsatirazi ziyenera kutsatiridwa poyambira koyamba:

• Gawo 1: Lumikizani wolamulira wa msonkhano wa EU-LX WiFi ndi zipangizo zonse zomwe zimayenera kuyang'anira Kuti mugwirizane ndi mawaya, chotsani chivundikiro cha wolamulira ndiyeno gwirizanitsani mawaya - izi ziyenera kuchitidwa monga momwe tafotokozera pa zolumikizira ndi zojambula mu bukhuli.
• Gawo 2. Yatsani magetsi, kuyang'ana ntchito ya zipangizo zolumikizidwa Pambuyo polumikiza zipangizo zonse, sinthani mphamvu ya wolamulira. Pogwiritsa ntchito ntchito ya Manual Operation (Menyu → Menyu ya Fitter → Ntchito Yamanja), yang'anani magwiridwe antchito a chipangizocho. Kugwiritsa ntchito mabatani, sankhani chipangizocho ndikusindikiza batani la MENU - chipangizo chomwe chiyenera kuyang'aniridwa chiyenera kuyatsa. Chongani zida zonse zolumikizidwa motere.
• Gawo 3. Khazikitsani nthawi ndi tsiku lomwe lilipo Kuti mukhazikitse tsiku ndi nthawi yomwe ilipo, sankhani Menyu → Zosintha za Controller → Zokonda za nthawi.

CHENJEZO
Nthawi yamakono ikhoza kusinthidwa kuchokera pa netiweki Menyu → Zosintha za Controller → Mipangidwe ya Nthawi→Zodziwikiratu.

Gawo 4. Konzani zowunikira kutentha, zowongolera zipinda Kuti wolamulira wa EU-LX WiFi athandizire gawo lomwe laperekedwa, liyenera kulandira chidziwitso cha kutentha komwe kulipo. Njira yosavuta ndiyo kugwiritsa ntchito kachipangizo ka kutentha kwa mawaya kapena opanda zingwe (monga EU-C-7p, EU-C-mini, EU-CL-mini, EU-C-8r). Komabe, ngati mukufuna kusintha kutentha komwe kwakhazikitsidwa mwachindunji kuchokera kuderali, mutha kugwiritsa ntchito zowongolera zipinda, mwachitsanzo, EU-R-8b, EU-R-8z, EU-R-8b Plus kapena odzipereka: EU- R-12b ndi EU-R-12s. Kuti muphatikize sensa ndi chowongolera, sankhani: Menyu → Menyu ya Fitter → Zone Zone… → Sensor yachipinda → Sankhani sensor.

Gawo 5. Konzani zida zotsalira zogwirizira Wowongolera wa EU-LX WiFi amathanso kugwiritsa ntchito zida izi:

• EU-i-1, EU-i-1m
• kusanganikirana valavu module EU-i-1, EU-i-1m- owonjezera kulankhula, mwachitsanzo EU-MW-1 (6 ma PC wolamulira)

Pambuyo posintha gawo la intaneti lomwe lamangidwa, wogwiritsa ntchito ali ndi mwayi wowongolera kuyika kudzera pa intaneti pogwiritsa ntchito emodul.pl. Kuti mudziwe zambiri za kasinthidwe, onani bukhu la gawo lomwe likufunika.

CHENJEZO
Ngati wogwiritsa ntchito akufuna kugwiritsa ntchito zidazi panthawi yogwira ntchito, ziyenera kulumikizidwa ndi / kapena kulembetsa.

MAIN SCREEN DESCRIPTION

Kuwongolera kumachitika pogwiritsa ntchito mabatani omwe ali pansi pa chiwonetsero.
Chiwonetsero cha Controller.

1. batani la MENU - likulowetsa mndandanda wa olamulira, kutsimikizira zoikamo.
2. batani - yomwe imagwiritsidwa ntchito kusakatula menyu kapena kuchepetsa mtengo wazomwe zasinthidwa. Batani ili limasinthanso magawo ogwiritsira ntchito pakati pa zigawo.
3. batani - yomwe imagwiritsidwa ntchito kusakatula menyu kapena kukulitsa mtengo wazomwe zasinthidwa. Batani ili limasinthanso magawo ogwiritsira ntchito pakati pa zigawo.
4. TULUKANI batani - TULUKANI kuchokera pamenyu yowongolera kapena kuletsa zosintha kapena sinthani chinsalu view (zoni, zoni).

Sampzowonetsera - ZONES 

1. Masiku ano la sabata
2. Kutentha kwakunja
3. Pampu kuthamanga
4. Kulumikizana kolumikizidwa kopanda kutero
5. Nthawi yapano
6. Zambiri zamachitidwe ogwiritsira ntchito/ndondomeko muzoni yoyenera
7. Mphamvu ya siginecha ndi momwe batire ilili pazidziwitso za sensor yachipinda
8. Khazikitsanitu kutentha m'dera lomwe mwapatsidwa
9. Kutentha kwapansi kwapano
10. Kutentha kwapano m'dera lomwe mwapatsidwa
11. Zone zambiri. Nambala yowoneka imatanthawuza sensa yolumikizidwa yachipinda yomwe imapereka chidziwitso cha kutentha komwe kulipo mdera lomwe likukhudzidwa. Ngati zone ikuwotha kapena kuziziritsa, kutengera mawonekedwe, manambala amawunikira. Ngati alamu ichitika m'dera lomwe mwapatsidwa, chizindikiro chokweza chidzawonetsedwa m'malo mwa manambala. Ku view magawo omwe akugwira ntchito pagawo linalake, wonetsani nambala yake pogwiritsa ntchito mabatani.

Sample Screen - ZONE

1. Kutentha kwakunja
2. Mkhalidwe wa batri
3. Nthawi yapano
4. Njira yamakono yogwiritsira ntchito zone yowonetsedwa
5. Kutentha kokonzedweratu kwa dera lomwe mwapatsidwa
6. Kutentha kwapano kwa dera lomwe mwapatsidwa
7. Kutentha kwapansi kwapano
8. Kutentha kwakukulu kwapansi
9. Zambiri pazambiri zamasensa olembetsedwa pazenera m'chigawocho
10. Zambiri za kuchuluka kwa ma actuators olembetsedwa muzoni
11. Chizindikiro cha zone yomwe ikuwonetsedwa pano
12. Chinyezi chapanopa muzoni yomwe wapatsidwa
13. Dzina lazone

NTCHITO ZA WOLAMULIRA

MALANGIZO OTHANDIZA 

Izi zimathandiza kutsegula kwa osankhidwa opareshoni mode.

• Normal mode - kutentha kokonzedweratu kumadalira ndandanda yokhazikitsidwa
• Nthawi ya tchuthi - kutentha kokhazikitsidwa kumadalira zokonda zamtunduwu
  Menyu → Menyu ya Fitter → Zone → Zone… → Zokonda → Zokonda kutentha > Nthawi ya tchuthi
• Economy mode - kutentha kokhazikitsidwa kumadalira zokonda zamtunduwu
  Menyu → Menyu ya Fitter → Zone → Zone… → Zikhazikiko → Zokonda kutentha > Mtundu wachuma
• Chitonthozo mode - kutentha kwayikidwa kumadalira zokonda zamtunduwu
  Menyu → Menyu ya Fitter → Zone → Zone… → Zikhazikiko → Zokonda kutentha> Mode yotonthoza

CHENJEZO

• Kusintha mawonekedwe kukhala tchuthi, chuma ndi chitonthozo chidzagwira ntchito kumadera onse. Ndizotheka kusintha kutentha kwa malo osankhidwa a zone inayake.
• Mumayendedwe ogwiritsira ntchito mosiyana ndi momwe zimakhalira, sizingatheke kusintha kutentha komwe kumayikidwa kuchokera ku chipinda chowongolera chipinda.

MALO

On
Kuti muwonetsetse kuti gawolo likugwira ntchito pazenera, lembani sensa mmenemo (onani: Menyu ya Fitter). Ntchitoyi imakupatsani mwayi woletsa zone ndikubisa magawo pazenera lalikulu.

Ikani kutentha
Kutentha kokhazikitsidwa muzoni kumachokera ku zoikamo za njira inayake yogwirira ntchito muzoni, mwachitsanzo, ndandanda ya sabata. Komabe, ndizotheka kuzimitsa ndondomekoyi ndikuyika kutentha kosiyana ndi nthawi ya kutentha kumeneku. Pambuyo pa nthawiyi, kutentha komwe kumayikidwa m'derali kudzadalira njira yomwe idakhazikitsidwa kale. Nthawi zonse, mtengo wamtengo wapatali wa kutentha, pamodzi ndi nthawi mpaka kumapeto kwa kutsimikizika kwake, ukuwonetsedwa pazenera lalikulu.

CHENJEZO
Ngati nthawi ya kutentha kwapadera kwayikidwa ku CON, kutentha kumeneku kudzakhala kovomerezeka kwa nthawi yosadziwika (kutentha kosasintha).

Njira yogwiritsira ntchito
Wogwiritsa akhoza view ndi kusintha zoikamo ntchito mode kwa zone.

• Dongosolo Lapafupi - Konzani zokonda zomwe zimagwira ntchito kuderali
• Pulogalamu Yapadziko Lonse 1-5 - Zokonda pandandandazi zimagwira ntchito kumadera onse, komwe akugwira ntchito
• Kutentha kosalekeza (CON) - ntchitoyi imakupatsani mwayi woyika kutentha komwe kudzakhala koyenera kudera lomwe mwapatsidwa kwamuyaya, mosasamala kanthu za nthawi ya tsiku.
• Ndi kuchepetsa nthawi - ntchitoyi imakulolani kuti muyike kutentha kosiyana komwe kudzakhala kovomerezeka kwa nthawi yeniyeni. Pambuyo pa nthawiyi, kutentha kudzachokera kumayendedwe omwe adagwiritsidwa ntchito kale (ndondomeko kapena nthawi zonse popanda malire a nthawi).

Kusintha kwadongosolo

Menyu → Zone → Zone… → Njira yogwiritsira ntchito → Ndandanda… → Sinthani

1. Masiku omwe zokonda zili pamwambazi zikugwira ntchito
2. Kutentha kumayikidwa kunja kwa nthawi
3. Khazikitsani kutentha kwa pakapita nthawi
4. Nthawi yosiyana

Kupanga ndandanda:

• Gwiritsani ntchito mivi yosankha gawo la sabata lomwe ndondomeko yokhazikitsidwa idzagwira ntchito (gawo loyamba la sabata kapena gawo la 1 la sabata).
• Gwiritsani ntchito batani la MENU kuti mupite kumalo osungira kutentha komwe kudzakhala kovomerezeka kunja kwa nthawi - ikani ndi mivi, tsimikizirani kugwiritsa ntchito batani la MENU.
• Gwiritsani ntchito batani la MENU kuti mupite ku zoikidwiratu za nthawi ndi kutentha komwe kudzakhala koyenera pa nthawi yomwe yatchulidwa, ikani pogwiritsa ntchito mivi, tsimikizirani ndi batani la MENU.
• Kenako pitilizani kukonzanso masiku omwe akuyenera kuperekedwa ku gawo loyamba kapena lachiwiri la sabata - masiku ogwira ntchito amawonetsedwa zoyera. Zokonda zimatsimikiziridwa ndi batani la MENU, mivi imayenda pakati pa tsiku lililonse.

Mukatha kukhazikitsa ndandanda ya masiku onse a sabata, dinani batani la EXIT ndikusankha njira ya Confirm ndi batani la MENU.

CHENJEZO
Wogwiritsa akhoza kukhazikitsa nthawi zitatu zosiyana mu ndondomeko yoperekedwa (molondola kwa mphindi 15).

ZOKHUDZA ZOKHALA

• Zikhazikiko za nthawi - nthawi ndi tsiku lomwe lilipo likhoza kutsitsidwa kuchokera pa intaneti ngati gawo la intaneti lalumikizidwa ndipo mawonekedwe odziyimira okha athandizidwa. Ndizothekanso kuti wogwiritsa ntchito aziyika pamanja nthawi ndi tsiku ngati njira yodziwikiratu siyikuyenda bwino.
• Zokonda pazenera - Ntchitoyi imalola wogwiritsa ntchito kusintha mawonekedwe.
• Ingolani mabatani - njirayi imagwiritsidwa ntchito kuti ipangitse phokoso lomwe lidzatsagana ndi kukanikiza mabatani.

FITTER'S MENU

Menyu ya Fitter ndiye menyu yovuta kwambiri yowongolera. Pano, wogwiritsa ntchito ali ndi ntchito zambiri zomwe zimalola kugwiritsa ntchito mphamvu za wolamulira.

MALO
Kuti mutsegule zone pazowonetsera zowongolera, lembani / yambitsani sensa mmenemo ndiyeno yambitsani chigawocho.

SENSOR YA PACHIPINDA
Wogwiritsa ntchito amatha kulembetsa / kupatsa sensor yamtundu uliwonse: NTC yolumikizidwa ndi waya, RS kapena opanda zingwe.

• Hysteresis - imawonjezera kulekerera kutentha kwa chipinda mumtundu wa 0.1 ÷ 5 ° C, pomwe palinso kutentha / kuziziritsa komwe kumayatsidwa.
  ExampLe: Kutentha kwa chipinda chokhazikitsidwa kale ndi 23 ° C Hysteresis ndi 1 ° C Sensa ya m'chipinda idzayamba kusonyeza kutentha kwa chipinda kutentha kutsika kufika 22 ° C.
• Kuwongolera - Kuwongolera kwa sensa ya chipinda kumachitika panthawi ya msonkhano kapena pakatha nthawi yayitali yogwiritsira ntchito sensa ngati kutentha kwa chipinda komwe kukuwonetsedwa kumapatuka pachomwecho. Kusintha kosiyanasiyana: kuchokera -10°C mpaka +10°C ndi sitepe ya 0.1°C.

KHALANI KUTEMIRIRA
Ntchitoyi ikufotokozedwa mu gawo la Menyu → Zones.

MALANGIZO OTHANDIZA
Ntchitoyi ikufotokozedwa mu gawo la Menyu → Zones.

KUSINTHA KWA ZOPHUNZITSA
Izi njira amazilamulira zotuluka: pansi mpope, angathe-free kukhudzana ndi zotuluka masensa 1-8 (NTC kulamulira kutentha mu zone kapena kachipangizo pansi kulamulira kutentha kwa pansi). Zotulutsa za sensor 1-8 zimaperekedwa ku zoni 1-8, motsatana. Mtundu wa sensa yomwe yasankhidwa apa idzawoneka mwachisawawa muzosankhazo: Menyu → Menyu ya Fitter → Magawo → Magawo… → Sensa yachipinda → Sankhani sensor (ya sensor ya kutentha) ndi Menyu → Menyu ya Fitter → Zone → Zone… → Kutentha kwapansi → Sensa yapansi → Sankhani sensa (ya sensor pansi). Zotulutsa za masensa onsewa zimagwiritsidwa ntchito kulembetsa zone ndi waya. Ntchitoyi imalolanso kuzimitsa mpope ndi kukhudzana muzoni yopatsidwa. Dera loterolo, ngakhale likufunika kutentha, silingatenge nawo gawo pakuwongolera.

ZOCHITIKA

• Kuwongolera kwanyengo - mwayi woyatsa / kuzimitsa zowongolera nyengo.

CHENJEZO
Kuwongolera kwanyengo kumagwira ntchito ngati mu menyu → Fitter's menyu → Sensa yakunja, njira yowongolera nyengo idawunikidwa.

• Kutentha - ntchitoyi imathandizira / kulepheretsa ntchito yotentha. Palinso kusankha kwa ndandanda yomwe ingakhale yovomerezeka pagawo panthawi yotenthetsera komanso kusintha kutentha kosiyana.
• Kuzizira - ntchitoyi imathandizira / kuyimitsa ntchito yozizirira. Palinso kusankha kwa ndandanda yomwe ingakhale yovomerezeka m'derali panthawi yozizirira ndikusintha kutentha kosiyana kosalekeza.
• Zokonda kutentha - ntchitoyi imagwiritsidwa ntchito poyika kutentha kwa njira zitatu zogwirira ntchito (Holiday mode, Economy mode, Comfort mode).

Kuyamba bwino kwambiri
Kuyamba bwino kwambiri ndi njira yanzeru yowongolera kutentha. Zimathandizira kuyang'anira kosalekeza kwa makina otenthetsera ndi kugwiritsa ntchito chidziwitsochi kuti chiziyambitsa kutentha pasadakhale nthawi yofunikira kuti ifike kutentha komwe kumayikidwa. Dongosololi silifuna kukhudzidwa kulikonse kwa wogwiritsa ntchito ndipo limayankha ndendende kusintha kulikonse komwe kumakhudza magwiridwe antchito a kutentha. Ngati, mwachitsanzoampLe, pali zosintha zomwe zimapangidwira kuyika ndipo nyumbayo imatenthetsa mwachangu, njira yabwino kwambiri yoyambira idzazindikiritsa kusintha kwa kutentha komwe kumapangidwa chifukwa cha ndandanda, ndipo m'kupita kotsatira kudzachedwetsa kuyambitsa kwa kutentha mpaka mphindi yotsiriza, kuchepetsa nthawi yofunikira kuti mufikire kutentha komwe kunakhazikitsidwa.

• nthawi yokonzedwa ya kusintha kutentha kwachuma kukhala komasuka Kuyambitsa ntchitoyi kudzaonetsetsa kuti kusintha kwadongosolo la kutentha komwe kumachitika chifukwa cha ndondomekoyi kumachitika, kutentha kwamakono m'chipindacho kudzakhala pafupi ndi mtengo womwe ukufunidwa.

CHENJEZO
The optimum start ntchito imagwira ntchito mu Kutentha mode.

ACTUATORS

• Zokonda
• SIGMA - ntchitoyi imathandizira kuwongolera kosasunthika kwa chowongolera magetsi. Wogwiritsa ntchito akhoza kukhazikitsa mawindo ocheperako komanso apamwamba kwambiri a valve - izi zikutanthauza kuti mlingo wa kutsegula ndi kutseka kwa valve sikudzapitirirabe izi. Kuonjezera apo, wogwiritsa ntchito amasintha Range parameter, yomwe imatsimikizira kutentha kwa chipinda chomwe valve idzayamba kutseka ndikutsegula.

CHENJEZO
Ntchito ya Sigma imangopezeka kwa STT-868 kapena STT-869 actuators.

Example

• Zone kutentha kokonzekera: 23˚C
• Kutsegula kochepa: 30%
• Kutsegula kwakukulu: 90%
• Ranji: 5˚C
• Hysteresis: 2˚C

Ndi zoikamo pamwamba, actuator adzayamba kutseka pamene kutentha mu zone kufika 18 ° C (kutentha preset kuchotsa mtengo osiyanasiyana). Kutsegula kochepa kudzachitika pamene kutentha kwa zone kukufika pa malo oikidwa.
Pamene malo okhazikitsidwa afika, kutentha m'derali kudzayamba kutsika. Ikafika pa 21 ° C (kutentha kocheperako hysteresis value), actuator imayamba kutseguka mpaka pomwe kutentha kumafika 18 ° C.

Chitetezo - Ntchitoyi ikasankhidwa, wowongolera amayang'ana kutentha. Ngati kutentha kwayikidwa kupyola ndi kuchuluka kwa madigiri mu Range parameter, ndiye kuti ma actuators onse omwe ali mugawo lopatsidwa adzatsekedwa (kutsegula kwa 0%). Ntchitoyi imangogwira ntchito ndi SIGMA yoyatsidwa.

• Emergency mode - Ntchitoyi imathandizira wogwiritsa ntchito kufotokozera kutsegulira kwa actuator komwe kudzakakamizika pakachitika alamu pamalo opatsidwa (kulephera kwa sensa, cholakwika cholumikizira).
• Actuator 1-6 - njira imathandizira wogwiritsa ntchito kulembetsa makina opanda zingwe. Kuti muchite izi, sankhani Register ndikusindikiza mwachidule batani loyankhulirana pa actuator. Pambuyo polembetsa bwino, ntchito yowonjezera yowonjezera imawonekera, kumene wogwiritsa ntchito angathe view magawo a actuator, mwachitsanzo, kuchuluka kwa batire, mtundu, ndi zina zambiri. Ndizothekanso kufufuta cholumikizira chimodzi kapena zonse nthawi imodzi.

ZINSINSI ZA WINDOW

Zokonda

• On - ntchitoyi imathandizira kutsegula kwa masensa a zenera m'malo opatsidwa (kulembetsa kwa sensa ya zenera kumafunika).
• Nthawi Yochedwa - Ntchitoyi imakupatsani mwayi wokhazikitsa nthawi yochedwa. Pambuyo pa nthawi yochedwa yokonzedweratu, wolamulira wamkulu amayankha kutsegulidwa kwa zenera ndikuletsa kutentha kapena kuziziritsa m'dera lomwelo.
  ExampLe: Nthawi yochedwa yakhazikitsidwa kukhala mphindi 10. Zenera litatsegulidwa, sensa imatumiza chidziwitso kwa woyang'anira wamkulu za kutsegula zenera. Sensa imatsimikizira zomwe zikuchitika pawindo nthawi ndi nthawi. Ngati itatha nthawi yochedwa (mphindi 10) zenera likadali lotseguka, wolamulira wamkulu adzatseka ma actuators ndikuzimitsa kutentha kwa dera.

CHENJEZO
Ngati nthawi yochedwa yakhazikitsidwa ku 0, ndiye kuti chizindikiro cha ma actuators kuti atseke chidzatumizidwa nthawi yomweyo.

• Zopanda zingwe - kusankha kulembetsa masensa zenera (1-6 pcs pa zone). Kuti muchite izi, sankhani Register ndikusindikiza mwachidule batani loyankhulirana pa sensa. Pambuyo polembetsa bwino, ntchito yowonjezera yowonjezera imawonekera, komwe wogwiritsa ntchito angathe view magawo a sensa, mwachitsanzo mawonekedwe a batri, mtundu, ndi zina zambiri. Ndizothekanso kufufuta sensa yomwe mwapatsidwa kapena zonse nthawi imodzi.

KUTENGA PANSI

Sensor Pansi

• Kusankha Sensor - Ntchitoyi imagwiritsidwa ntchito kuthandizira (za waya) kapena kulembetsa (zopanda ziwaya) masensa apansi. Pankhani ya sensa yopanda zingwe, lembani ndikuwonjezeranso batani lolumikizana pa sensa.
• Hysteresis - imawonjezera kulekerera kutentha kwa chipinda m'kati mwa 0.1 ÷ 5 ° C, pomwe kutentha kowonjezera / kuzizira kumathandizidwa.

ExampLe:
Kutentha kwakukulu kwapansi ndi 45 ° C Hysteresis ndi 2 ° C Woyang'anira adzaletsa kukhudzana pambuyo pa 45 ° C pa sensa ya pansi. Ngati kutentha kumayamba kutsika, kukhudzana kudzasinthidwanso pambuyo pa kutentha pansi pa sensa kumatsika mpaka 43 C (pokhapokha ngati kutentha kwa chipinda kwafikira).

• Kuwongolera - Kuwongolera kwa sensa ya pansi kumachitika panthawi ya msonkhano kapena pakatha nthawi yayitali yogwiritsira ntchito sensa ngati kutentha kwapansi komwe kumawonekera kumapatuka kuchokera ku zenizeni. Kusintha kosiyanasiyana: kuchokera -10°C mpaka +10°C ndi sitepe ya 0.1°C.

CHENJEZO
Sensa yapansi sigwiritsidwa ntchito panthawi yozizira.

Njira yogwiritsira ntchito

• Kuzimitsa - Kusankha njirayi kumalepheretsa kutentha kwapansi, mwachitsanzo, Chitetezo cha Pansi kapena Comfort Mode sikugwira ntchito.
• Chitetezo cha pansi - Ntchitoyi imagwiritsidwa ntchito kusunga kutentha kwapansi pansi pa kutentha kwakukulu kuti kuteteze dongosolo kuti lisatenthedwe. Kutentha kukakwera mpaka kutentha kwakukulu, kutenthetsanso kwa zone kudzazimitsidwa.
• Comfort mode - Ntchitoyi imagwiritsidwa ntchito kuti pakhale kutentha kwapansi bwino, mwachitsanzo, wowongolera aziwunika kutentha komwe kulipo. Kutentha kukakwera mpaka kutentha kwakukulu, kutentha kwa zone kudzazimitsidwa kuteteza dongosolo kuti lisatenthedwe. Pamene kutentha kwapansi kutsika pansi pa kutentha kocheperako, zone reheat idzayatsidwanso.

Min. kutentha
Ntchitoyi imagwiritsidwa ntchito kukhazikitsa kutentha kochepa kuti kuteteze pansi kuti zisazizire. Pamene kutentha kwapansi kutsika pansi pa kutentha kocheperako, zone reheat idzayatsidwanso. Ntchitoyi imapezeka pokhapokha mutasankha Comfort Mode.

Max. kutentha
Kutentha kwakukulu kwapansi ndi kutentha kwapansi pamwamba pomwe wolamulira adzazimitsa kutentha mosasamala kanthu za kutentha kwa chipinda. Ntchitoyi imateteza kuyika kwa kutentha.

ZOWONJEZERA ZOWONJEZERA
Ntchitoyi imakuthandizani kuti muzitha kulumikizana ndi zina. Choyamba, m'pofunika kulembetsa kukhudzana koteroko (1-6 ma PC.). Kuti muchite izi, sankhani njira yolembetsa ndikusindikiza mwachidule batani lolumikizana pa chipangizocho, mwachitsanzo MW-1.
Pambuyo polembetsa ndikusintha chipangizocho, zotsatirazi ziwoneka:

• Chidziwitso - zambiri zokhudzana ndi mawonekedwe, mawonekedwe ogwiritsira ntchito ndi mtundu wolumikizirana zikuwonetsedwa pazenera lowongolera
• Yatsani - kusankha kuyatsa / kuletsa ntchito yolumikizirana
• Njira yogwiritsira ntchito - njira yopezeka ndi wogwiritsa ntchito kuti mutsegule njira yolumikizirana yosankhidwa
• Nthawi - ntchitoyo imalola kukhazikitsa nthawi yolumikizirana kwa nthawi inayake Wogwiritsa ntchito amatha kusintha mawonekedwe posankha / kusankha Njira Yogwira ndikukhazikitsa nthawi yamtunduwu.
• Nthawi zonse - ntchitoyi imalola kuyika wolumikizanayo kuti agwire ntchito mpaka kalekale. Ndizotheka kusintha mawonekedwe olumikizana nawo posankha / kusankha Njira Yogwira
• Relays - kulumikizana kumagwira ntchito molingana ndi madera omwe adapatsidwa
• Dehumidification - ngati Chinyezi Chochuluka chadutsa m'dera lomwe mwapatsidwa, njirayi imakupatsani mwayi woyambitsa chowumitsira mpweya.
• Zokonda - ntchitoyi imakupatsani mwayi wokhazikitsa ndandanda yolumikizirana yosiyana (mosasamala kanthu za malo owongolera).

CHENJEZO
Ntchito ya Dehumidification imagwira ntchito mu Kuzizira kokha.

• Chotsani - njirayi imagwiritsidwa ntchito kuchotsa wosankhidwayo.

VAVU YOSANGALALA
Wolamulira wa EU-LX WiFi amatha kugwiritsa ntchito valavu yowonjezera pogwiritsa ntchito gawo la valve (mwachitsanzo i-1m). Valavu iyi ili ndi kulumikizana kwa RS, koma ndikofunikira kuti mulembetse, zomwe zimafuna kuti mutchule nambala ya module yomwe ili kumbuyo kwa nyumba yake, kapena pulogalamu yachidziwitso cha pulogalamu). Pambuyo pa kulembetsa kolondola, ndizotheka kukhazikitsa magawo amtundu wina wa valve yowonjezera.

• Zambiri - ntchitoyo imakulolani kutero view mawonekedwe a valve.
• Register - Mukalowetsa kachidindo kumbuyo kwa valve kapena mu Menyu → Information Software, mukhoza kulembetsa valavu ndi wolamulira wamkulu.
• Pamanja mode - wogwiritsa ntchito amatha kuyimitsa pamanja ntchito ya valve, kutsegula / kutseka valavu ndikusintha mpope ndikuzimitsa kuti azitha kuyendetsa bwino zipangizo.
• Baibulo - Ntchitoyi ikuwonetsa nambala ya pulogalamu ya valve. Chidziwitso ichi ndi chofunikira polumikizana ndi ntchitoyi.
• Kuchotsa vavu - Ntchitoyi imagwiritsidwa ntchito kuchotsa valavu kwathunthu. Ntchitoyi imagwiritsidwa ntchito, mwachitsanzoample, pochotsa valavu kapena kusintha gawolo (ndikofunikira kulembetsanso gawo latsopano).
• On - njira yotsegulira kapena kuletsa valavu kwakanthawi.
• Kutentha kwa ma valve - chizindikiro ichi chimakulolani kuti muyike kutentha kwa valve.
• Nthawi yachilimwe - Kuyatsa mawonekedwe achilimwe kumatseka valavu kuti mupewe kutentha kosafunikira kwa nyumbayo. Ngati kutentha kwa boiler kuli kokwera kwambiri (chitetezo cha boiler chothandizira chimafunikira), valavu idzatsegulidwa mwadzidzidzi. Mode iyi sikugwira ntchito muchitetezo cha Kubwerera.
• Kuwongolera - Ntchitoyi ingagwiritsidwe ntchito poyesa valavu yomangidwa, mwachitsanzo, mutatha kugwiritsa ntchito nthawi yayitali. Pakuwongolera, valavu imayikidwa pamalo otetezeka, mwachitsanzo kuti CH valve ndi mtundu wa chitetezo cha Return kuti ufikire malo ake otseguka, komanso kuti valve yapansi ndi mtundu Wozizira, ibwerere kwathunthu kumalo ake otsekedwa.
• Sitiroko imodzi - Ichi ndiye sitiroko imodzi yokha (kutsegula kapena kutseka) yomwe valavu imatha kuchita panthawi ya kutentha kumodziampling. Ngati kutentha kuli pafupi ndi malo oikika, sitiroko iyi imawerengedwa kutengera gawo la Proportional coefficient parameter. Zing'onozing'ono za unit sitiroko, m'pamenenso kutentha kwakhazikitsidwa kungafikire, koma kutentha komwe kumayikidwa kumafikira nthawi yayitali.
• Kutsegula kochepa - Gawo lomwe limatanthawuza kutseguka kwa valve yaying'ono peresenti. Parameter iyi imathandizira kuti valavu ikhale yotseguka pang'ono kuti isunge kuyenda kochepa.

CHENJEZO
Ngati tiyika kutsegulira kochepa kwa valve ku 0% (kutseka kwathunthu), mpope sidzagwira ntchito pamene valve yatsekedwa.

• Nthawi yotsegulira - Gawo lomwe limatanthawuza nthawi yomwe imatengera woyendetsa valve kuti atsegule valavu kuchokera ku 0% mpaka 100%. Nthawiyi iyenera kusankhidwa kuti ifanane ndi ya valve actuator (monga momwe zasonyezedwera pa nameplate).
• Kuyimitsa kaye - Gawoli limatsimikizira kuchuluka kwa kuyeza (kuwongolera) kwa kutentha kwa madzi pansi pa valavu yoyika CH. Ngati sensa ikuwonetsa kusintha kwa kutentha (kuchoka pa malo oikidwa), ndiye kuti valve ya solenoid idzatsegula kapena kutseka ndi mtengo wokonzedweratu kuti ubwerere kutentha komwe kumayikidwa.
• Valve Hysteresis - Njirayi imagwiritsidwa ntchito poyika ma valve setpoint kutentha kwa hysteresis. Uwu ndiye kusiyana pakati pa kutentha kokhazikitsidwa kale ndi kutentha komwe valavu imayamba kutseka kapena kutseguka.

ExampLe: Kutentha kokhazikitsidwa kale kwa vavu: 50°C

• Hysteresis: 2°C
• Kuyimitsa ma valve: 50°C
• Kutsegula kwa valve: 48°C
• Kutseka kwa valve: 52°C

Pamene kutentha kwayikidwa ndi 50 ° C ndipo hysteresis ndi 2 ° C, valavu imayima pamalo amodzi pamene kutentha kufika 50 ° C, pamene kutentha kumatsikira ku 48 ° C, kumayamba kutseguka ndipo ikafika 52. °C, valavu idzayamba kutseka kuti muchepetse kutentha.

• Mtundu wa vavu - Njira iyi imathandizira wogwiritsa ntchito kusankha mitundu yotsatirayi:
• CH valve - kukhazikitsa pamene tikufuna kulamulira kutentha mu dera la CH pogwiritsa ntchito sensa ya valve. Sensa ya valve iyenera kuyikidwa pansi pa valavu yosakaniza pa chitoliro choperekera.
• Valve yapansi - khalani ndi nthawi yomwe tikufuna kusintha kutentha pagawo lotenthetsera pansi. Mtundu wapansi umateteza dongosolo la pansi ku kutentha kwakukulu. Ngati mtundu wa valve umayikidwa ngati CH ndipo umagwirizanitsidwa ndi dongosolo la pansi, ukhoza kuwononga dongosolo la pansi.
• Bweretsani chitetezo - khazikitsani pamene tikufuna kusintha kutentha pakubwerera kwa kukhazikitsa kwathu pogwiritsa ntchito sensa yobwerera. Mawotchi obwerera okha ndi otenthetsera akugwira ntchito mumtundu uwu wa valve, ndipo sensa ya valve sikugwirizana ndi wolamulira. Pakukonzekera uku, valavu imateteza kubwerera kwa boiler ku kutentha kozizira monga chofunikira, ndipo ngati ntchito yoteteza Boiler yasankhidwa, imatetezanso chowotcha kuti chisawotche. Ngati valavu yatsekedwa (0% yotseguka), madzi amangoyenda pang'onopang'ono, pamene kutsegula kwathunthu kwa valve (100%) kumatanthauza kuti dera lalifupi latsekedwa ndipo madzi akuyenda kudutsa pakati pa kutentha kwapakati.

CHENJEZO
Ngati Chitetezo cha Boiler chazimitsidwa, kutentha kwa CH sikudzakhudza kutsegula kwa valve. Zikavuta kwambiri, chotenthetsera chikhoza kutenthedwa, choncho tikulimbikitsidwa kuti tikonze zosungirako zotetezera.
Kwa mtundu uwu wa vavu, tchulani Return Protection Screen.

• Kuziziritsa - kuyika pamene tikufuna kusintha kutentha kwa dongosolo lozizira (valavu imatsegula pamene kutentha kwayikidwa kumakhala kotsika kuposa kutentha kwa sensa ya valve). Chitetezo cha boiler ndi Kubwereranso chitetezo sichigwira ntchito mumtundu uwu wa valve. Valavu yamtunduwu imagwira ntchito ngakhale kuti nthawi ya Chilimwe ikugwira ntchito, pomwe pampu imagwira ntchito potseka. Kuonjezera apo, valavu yamtunduwu imakhala ndi mphira yotentha yosiyana yomwe imaphatikizidwa ngati ntchito ya Weather sensor.
• Kutsegula mu CH calibration - Ntchitoyi ikayatsidwa, valavu imayamba kuwongolera kuyambira gawo lotsegulira. Ntchitoyi imapezeka kokha pamene mtundu wa valve umayikidwa ngati CH Valve.
• Kutentha kwapansi - chilimwe - Ntchitoyi imangowonekera mutasankha mtundu wa valve ngati Floor Valve. Ntchitoyi ikatha, valve yapansi idzagwira ntchito mu Chilimwe Mode.
• Kuwongolera nyengo - Kuti ntchito ya nyengo ikhale yogwira ntchito, ikani sensa yakunja pamalo osadziwika, omwe sakukhudzidwa ndi mphamvu za mumlengalenga. Pambuyo kukhazikitsa ndi kulumikiza sensa, sinthani ntchito ya Weather Control mumenyu yowongolera.

CHENJEZO
Zokonda izi sizikupezeka mumayendedwe Oziziritsa ndi Kubwereranso.

Kutentha pamapindikira - iyi ndi yokhotakhota molingana ndi momwe kutentha kwa wolamulira kumatsimikiziridwa pamaziko a kutentha kwakunja. Kuti valavu igwire bwino ntchito, kutentha kwapadera (kutsika kwa valve) kumayikidwa pazigawo zinayi zapakati pa kutentha kwapakati: -20 ° C, -10 ° C, 0 ° C ndi 10 ° C. Pali njira yotenthetsera yosiyana ya Kuzizira. Amayikidwa kuti azitentha kunja kwapakati: 10°C, 20°C, 30°C, 40°C.

Wowongolera zipinda

• Mtundu wowongolera
• Kulamulira popanda chipinda chowongolera - Njirayi iyenera kufufuzidwa pamene sitikufuna kuti chipinda chowongolera chikhudze ntchito ya valve.
• RS regulator - kuchepa - fufuzani njirayi ngati valavu iyenera kuyendetsedwa ndi chipinda chowongolera chipinda chokhala ndi RS kulankhulana. Ntchitoyi ikayang'aniridwa, wowongolera azigwira ntchito molingana ndi kutentha kwa chipinda cham'munsi. parameter.
• RS regulator - gawo - Pamene chowongolera ichi chayatsidwa, kutentha kwapano ndi kutentha kwa valve kumatha kukhala viewed. Ntchitoyi itayang'aniridwa, wolamulira adzagwira ntchito molingana ndi Kusiyana kwa Kutentha kwa Malo ndi Setpoint Temperature Change magawo.
• Woyang'anira chipinda chokhazikika - njirayi imayang'aniridwa ngati valavu iyenera kuyendetsedwa ndi olamulira a mayiko awiri (osakhala ndi RS kulankhulana). Ntchitoyi ikayang'aniridwa, wowongolera azigwira ntchito molingana ndi gawo lotsika la Room regulator.
  • Kutentha kwa chipinda chowongolera. m'munsi - Muchikhazikitso ichi, sungani mtengo umene valve idzachepetse kutentha kwake pamene kutentha kumayikidwa mu chipinda chowongolera chipinda (kutentha kwa chipinda).

CHENJEZO
Izi zimagwira ntchito kwa Standard room regulator ndi RS regulator kuchepetsa ntchito.

• • Kusiyana kwa kutentha kwa chipinda - Kukonzekera uku kumatsimikizira kusintha kwa unit mu kutentha kwa chipinda (kufupi ndi 0.1 ° C) kumene kusintha kwapadera kwa kutentha kwa valve kudzachitika.
  • Kusintha kwa kutentha kwayikidwa - Kukonzekera uku kumatsimikizira kuchuluka kwa kutentha kwa valve kudzawonjezeka kapena kuchepa ndi kusintha kwa unit kutentha kwa chipinda (onani: Kusiyana kwa kutentha kwa chipinda). Ntchitoyi imangogwira ntchito ndi RS room regulator ndipo imagwirizana kwambiri ndi kutentha kwa chipinda.

ExampLe: Kusiyana kwa kutentha kwazipinda: 0.5°C

• • Kusintha kwa kutentha kwa ma valve: 1°C
  • Kutentha kwa ma valve: 40°C
  • Kutentha kwa chowongolera chipinda: 23°C

Ngati kutentha kwa chipinda kumakwera kufika ku 23.5 ° C (ndi 0.5 ° C pamwamba pa kutentha kwa chipinda), valve imatseka ku 39 ° C preset (ndi 1 ° C).

CHENJEZO
Gawoli likugwira ntchito ku RS proportional regulator function.

• Ntchito yoyang'anira chipinda - Mu ntchitoyi, ndikofunikira kukhazikitsa ngati valavu idzatseka (Kutseka) kapena kutentha kumatsika (Kutentha kwa chipinda chowongolera kutsika) kukatenthedwa.
• Proportionality coefficient - The proportionality coefficient imagwiritsidwa ntchito kudziwa kugunda kwa valve. Kuyandikira kwa kutentha komwe kumayikidwa, kumachepetsanso sitiroko. Ngati coefficient iyi ndi yapamwamba, valavu idzafika potsegula mofananamo mofulumira, koma idzakhala yocheperako. Chiwerengerotage ya kutsegulidwa kwa unit imawerengeredwa pogwiritsa ntchito njira iyi: (kutentha kwa sensa - kutentha kwa sensor.) x (proportionality coefficient/10)
• Kutentha kwakukulu kwapansi - Ntchitoyi imatchula kutentha kwakukulu komwe sensor ya valve imatha kufika (ngati Floor valve yasankhidwa). Mtengo uwu ukafika, valavu imatseka, kuzimitsa mpope, ndipo chidziwitso chokhudza kutentha kwapansi chikuwonekera pawindo lalikulu la wolamulira.

CHENJEZO
Izi zimangowoneka ngati mtundu wa valavu wakhazikitsidwa ku valavu ya Floor.

• Njira yotsegulira - Ngati, mutagwirizanitsa valavu kwa wolamulira, zikuwoneka kuti zimayenera kulumikizidwa kumbali ina, sikoyenera kusintha mizere yoperekera, koma n'zotheka kusintha njira yotsegulira ya valve. posankha njira yosankhidwa: Kumanja kapena Kumanzere.
• Kusankhidwa kwa Sensor - Njirayi ikugwiritsidwa ntchito ku sensa yobwerera ndi sensa yakunja ndipo imakulolani kuti mudziwe ngati ntchito yowonjezera ya valve iyenera kuganizira Self ya valve module kapena Main sensor (Pokha mu Njira ya Akapolo).
• CH kusankha sensor - Njirayi ikugwiritsidwa ntchito ku CH sensor ndipo imakulolani kuti mudziwe ngati ntchito ya valve yowonjezera iyenera kuganizira Self ya valve module kapena Main sensor (Pokhapokha muakapolo akapolo).
• Chitetezo cha boiler - Izi zimapereka chitetezo ku kutentha kwambiri kwa CH, ndipo cholinga chake ndi kuteteza kutentha koopsa kwa boiler. Wogwiritsa ntchitoyo ayambe akhazikitsa kutentha kokwanira kovomerezeka. Pakachitika kutentha koopsa, valavu imayamba kutseguka kuti iziziritse boiler pansi. Wogwiritsanso amaika kutentha kwakukulu kovomerezeka kwa CH, pambuyo pake valve idzatsegulidwa.

CHENJEZO
Ntchitoyi sikugwira ntchito pamitundu yoziziritsa komanso yapansi.

• Kubwezeretsanso chitetezo - Ntchitoyi imalola kukhazikitsa chitetezo cha boiler kumadzi ozizira kwambiri obwerera kuchokera kudera lalikulu, zomwe zingayambitse kutentha kwa kutentha kwa boiler. Chitetezo chobwereranso chimagwira ntchito kotero kuti pamene kutentha kuli kochepa kwambiri, valavu imatseka mpaka kachigawo kakang'ono ka boiler kakufika kutentha kofunikira.

CHENJEZO
Ntchitoyi sikuwoneka ya mtundu wa valve Kuzizira.

Pampu ya valve

• Njira zopangira pampu - ntchitoyi imakupatsani mwayi wosankha njira yogwiritsira ntchito pampu:
  • Nthawizonse WODZIWA - mpope umazimitsidwa kwamuyaya ndipo wolamulira amangoyang'anira ntchito ya valve
  • ONSE ONSE - mpope umayenda nthawi zonse mosasamala kanthu za kutentha
  • Pamwamba pamtunda - pampu imatembenukira pamwamba pa kutentha kosinthika. Ngati pampu iyenera kuyatsidwa pamwamba pa chiwombankhanga, kutentha kwa pampu ya pakhomo kuyeneranso kukhazikitsidwa. Mtengo wochokera ku sensa ya CH umaganiziridwa.
• Mapampu amasintha kutentha - Njirayi ikugwira ntchito pampopu yomwe ikugwira ntchito pamwamba pa khomo. Pampu ya valavu idzayatsidwa pamene sensa ya boiler ifika pa kutentha kwa pampu.
• Pampu yoletsa kuyimitsa - ikayatsidwa, pampu ya valve imayatsa masiku 10 aliwonse kwa mphindi ziwiri. Izi zimalepheretsa madzi kuti asawononge kuikapo kunja kwa nyengo yotentha.
• Kutseka pansi pa kutentha kwa kutentha - Pamene ntchitoyi itsegulidwa (yang'anani Njira Yothandizira), valavu idzakhala yotsekedwa mpaka sensor ya boiler ikufika pa kutentha kwa pampu.

CHENJEZO
Ngati gawo lowonjezera la valve ndi chitsanzo cha i-1, ntchito zotsutsana ndi zowonongeka za mapampu ndi kutsekedwa pansi pa khomo kungakhazikitsidwe mwachindunji kuchokera ku sub-menu ya gawolo.

• Chipinda chowongolera pampu ya mavavu - Njira yomwe chowongolera chipinda chimazimitsa pompayo ikatenthedwa.
• Kupopera kokha - Pamene kuthandizidwa, wolamulira amangoyang'anira pampu yokha ndipo valve sichiyendetsedwa.
• Kuwongolera kwa sensor yakunja - Ntchitoyi imagwiritsidwa ntchito kusinthira sensa yakunja, imachitika panthawi yoyika kapena pambuyo pakugwiritsa ntchito sensor kwa nthawi yayitali ngati kutentha kwakunja komwe kukuwonetsedwa kumapatuka ku zenizeni. Wogwiritsa amatchula mtengo wowongolera womwe wagwiritsidwa ntchito (kusintha kosiyanasiyana: -10 mpaka +10 ° C).
• Kutseka kwa valve - Parameter yomwe khalidwe la valve mu CH mode limayikidwa pambuyo pozimitsa. Kutsegula njira iyi kumatseka valavu ndikuyimitsa kumatsegula.
• Kuwongolera kwa ma valve mlungu ndi mlungu - Kuwongolera kwa mlungu ndi mlungu kumakupatsani mwayi wokonza zopatuka za kutentha kwa ma valve pamasiku ena a sabata nthawi zina. Kutentha kwapakati kumayikidwa pa +/-10 ° C.
  Kuti mulole kulamulira kwa mlungu ndi mlungu, sankhani ndikuyang'ana Mode 1 kapena Mode 2. Zosintha mwatsatanetsatane zamitunduyi zingapezeke m'zigawo zotsatirazi za submenu: Ikani Mode 1 ndi Set Mode 2.

CHONDE DZIWANI
Kuti mugwiritse ntchito moyenera ntchitoyi, ndikofunikira kukhazikitsa tsiku ndi nthawi yomwe ilipo.

MODE 1 - munjira iyi, ndizotheka kupanga zopatuka za kutentha komwe kwakhazikitsidwa tsiku lililonse la sabata padera. Kuchita izi:

• Sankhani njira: Khazikitsani Mode 1
• Sankhani tsiku la sabata limene mukufuna kusintha kutentha
• Gwiritsani ntchito mabatani kuti musankhe nthawi yomwe mukufuna kusintha kutentha. Tsimikizirani zomwe mwasankha podina batani la MENU
• Zosankha zimawonekera pansi, sankhani CHANGE pokanikiza batani la MENU pamene likuwonekera moyera.
• Kenako chepetsa kapena onjezerani kutentha ndi mtengo wosankhidwa ndikutsimikizira.
• Ngati mukufuna kuyikanso kusintha komweku ku maola oyandikana nawo, dinani batani la MENU pazikhazikiko zomwe mwasankha, ndipo njira ikawonekera pansi pazenera, sankhani COPY ndikukopera zosinthazo ku ola lotsatira kapena lapitalo pogwiritsa ntchito mabatani. Tsimikizirani makonda pokanikiza MENU.

ExampLe:

Pankhaniyi, ngati kutentha kumayikidwa pa valve ndi 50 ° C, Lolemba, kuchokera ku 4 00 mpaka 7 00 maola, kutentha komwe kumayikidwa pa valve kudzawonjezeka ndi 5 C, kapena 55 C; m'maola kuchokera ku 7 00 mpaka 14 00 idzachepa ndi 10 C, kotero idzakhala 40 C, pamene pakati pa 17 00 ndi 22 00 idzawonjezeka kufika ku 57 C. MODE 2 - munjira iyi, ndizotheka kukonza kusintha kwa kutentha mwatsatanetsatane kwa masiku onse ogwira ntchito (Lolemba - Lachisanu) komanso kumapeto kwa sabata (Loweruka - Lamlungu). Kuchita izi:

• Sankhani njira: Khazikitsani Mode 2
• Sankhani gawo la sabata lomwe mukufuna kusintha kutentha
• Njira inanso ndi yofanana ndi mu Mode 1

ExampLe:

Pankhaniyi, ngati kutentha kumayikidwa pa valve ndi 50 C Lolemba mpaka Lachisanu, kuchokera ku 4 00 mpaka 7 00, kutentha kwa valve kudzawonjezeka ndi 5 C, kapena 55 C; m'maola kuchokera ku 7 00 mpaka 14 00 idzachepa ndi 10 C, kotero idzakhala 40 C, pamene pakati pa 17 00 ndi 22 00 idzawonjezeka kufika ku 57 C. Pakati pa sabata, kuchokera ku 6 00 mpaka 9 00 maola, kutentha kwa vavu kudzakwera ndi 5 C, ndiko kuti ku 55 C, ndipo pakati pa 17 00 ndi 22 00 kudzakwera kufika 57 C.

• Zokonda pafakitale - Parameter iyi imakulolani kuti mubwerere ku zoikamo za valve yoperekedwa yosungidwa ndi wopanga. Kubwezeretsa makonzedwe a fakitale kumasintha mtundu wa valve ku CH valve.

INTERNET MODULE
Module ya intaneti ndi chipangizo chomwe chimalola kuwongolera kwakutali pakuyika. Wogwiritsa ntchito amatha kuwongolera magwiridwe antchito a zida zosiyanasiyana ndikusintha magawo ena pogwiritsa ntchito pulogalamu ya emodul.pl. Chipangizocho chili ndi gawo la intaneti lopangidwa. Pambuyo poyatsa gawo la intaneti ndikusankha njira ya DHCP, wolamulirayo adzapezanso magawo monga: IP adilesi, IP mask, Gateway adilesi ndi adilesi ya DNS kuchokera pa netiweki yakomweko.

Zokonda pamanetiweki zofunika
Kuti gawo la intaneti lizigwira ntchito moyenera, likufunika kulumikiza gawolo ku netiweki yokhala ndi seva ya DHCP ndi doko lotseguka 2000. Module ya intaneti ikalumikizidwa bwino ndi netiweki, pitani ku menyu zoikamo gawo (mu master controller). Ngati intaneti ilibe seva ya DHCP, gawo la intaneti liyenera kukonzedwa ndi woyang'anira wake polowetsa magawo oyenerera (DHCP, IP Address, Gateway Address, Subnet Mask, DNS Address). Kusintha kungatheke ndi:

1. Pitani ku zoikamo menyu ya Internet module.
2. Sankhani "Yathandizira" njira
3. Kenako onani ngati njira ya "DHCP" yafufuzidwa.
4. Lowetsani "WIFI Selection"
5. Kenako sankhani maukonde anu a WIFI ndikulowetsa mawu ake achinsinsi.
6. Dikirani pang'ono (pafupifupi 1min) ndikuwona ngati adilesi ya IP yaperekedwa. Pitani ku "IP Address" tabu ndikuwona ngati mtengo ndi wosiyana ndi 0.0.0.0/ -.-.-.- .
   • Ngati mtengo ukusonyezabe 0.0.0.0 / -.-.-.-.- fufuzani zoikamo maukonde kapena Efaneti kugwirizana pakati pa gawo Internet ndi chipangizo.
7. Pambuyo popereka adilesi ya IP moyenera, titha kuyamba kulembetsa gawolo kuti tipange khodi yomwe ikufunika kuti iperekedwe ku akaunti yofunsira.

NJIRA YOPHUNZITSIRA
Ntchitoyi imakupatsani mwayi wowongolera magwiridwe antchito a zida zapayekha. Wogwiritsa ntchito amatha kusintha pamanja pazida zilizonse: mpope, kulumikizana kwaulere komanso ma valve actuators. Ndikofunikira kugwiritsa ntchito njira yopangira pamanja, kuti muwone momwe zida zolumikizira zimagwirira ntchito poyambira koyamba.

ZOTI ZONSE ZONSE

CHENJEZO
Ntchitoyi imapezeka pokhapokha sensa yakunja yalembedwa mu EU-LX WiFi controller.
Mutha kulumikiza sensa yakunja ya kutentha kwa EU-LX WiFi controller (cholumikizira mu chowongolera- Sensor yowonjezera 1), yomwe imakupatsani mwayi wosinthira kuwongolera kwanyengo, ndi:

• Kusankha Sensor - Mutha kusankha sensor ya waya ya NTC kapena C-8zr yopanda zingwe. Sensa yopanda zingwe imafuna kulembetsa.
• Calibration - Kuwongolera kumachitika pakuyika kapena pambuyo pakugwiritsa ntchito sensor kwa nthawi yayitali ngati kutentha komwe kumayesedwa ndi sensor kumachoka pa kutentha kwenikweni. Kusintha kosiyanasiyana kumayambira -10°C mpaka +10°C ndi sitepe ya 0.1°C.

Pankhani ya sensa yopanda zingwe, magawo otsatirawa akukhudzana ndi kuchuluka kwa batri ndi kuchuluka kwake.

KUYAMBIRA KUYIMALA
Ntchito yoletsa ma actuators kuti asayatse pakapita nthawi.

• Zokonda tsiku
  • Kuletsa Kutentha - Khazikitsani tsiku lomwe kutentha kuzimitsidwa
  • Kutsegula kwa kutentha - kukhazikitsa tsiku lomwe kutentha kudzayatsidwa
• Kuwongolera kwanyengo - Pamene sensa yakunja ikugwirizanitsidwa, chinsalu chachikulu chidzawonetsa kutentha kwakunja ndipo mndandanda wa olamulira udzawonetsa kutentha kwakunja.
  Ntchito yochokera kunja kwa kutentha imalola kudziwa kutentha kwapakati, komwe kudzagwira ntchito molingana ndi kutentha kwa kutentha. Ngati kutentha kwapakati kupitirira malire a kutentha kwapadera, wolamulirayo azimitsa kutentha kwa malo omwe ntchito yolamulira nyengo ikugwira ntchito.
• Yatsani - kugwiritsa ntchito kuwongolera nyengo, sensor yosankhidwa iyenera kuyatsidwa.
• Nthawi yowerengera - wogwiritsa ntchito amaika nthawi pamaziko omwe kutentha kwakunja kudzawerengedwa. Nthawi yokhazikitsa ndi kuyambira maola 6 mpaka 24.
• Kutentha kwapakati - iyi ndi ntchito yoteteza ku kutentha kwambiri kwa dera lomwe mwapatsidwa. Dera lomwe zonera zimayatsidwa zidzatsekedwa kuti zisatenthe kwambiri ngati kutentha kwapanja tsiku lililonse kupitilira kutentha komwe kwakhazikitsidwa. Za example, kutentha kukakwera m'chaka, wolamulirayo amaletsa kutentha kwachipinda kosafunikira.
• Avereji ya kutentha kwakunja - mtengo wa kutentha wowerengedwa pamaziko a Avereji nthawi.

KUGWIRITSA NTCHITO KWAULERE
Wolamulira wa EU-LX WiFi adzayambitsa kukhudzana kwaulere (pambuyo powerengera nthawi yochedwa) pamene madera onse sanafike pa kutentha (kutentha - pamene chigawocho chatenthedwa, kuzizira - pamene kutentha m'derali kuli kotentha. kwambiri). Woyang'anira amaletsa kukhudzana ndi kutentha komwe kumayikidwa.

• Kuchedwa kwa ntchito - ntchitoyi imalola wogwiritsa ntchito kukhazikitsa nthawi yochedwa yosinthira kukhudzana kopanda mphamvu pambuyo poti kutentha kumatsika pansi pa kutentha komwe kumayikidwa m'madera aliwonse.

PUMP
Wolamulira wa EU-LX WiFi amayang'anira ntchito ya mpope - imayatsa mpope (pambuyo powerengera nthawi yochedwa) pamene madera aliwonse akutenthedwa komanso pamene njira yapampopi yapansi imayatsidwa m'deralo. Magawo onse akatenthedwa (kutentha kokhazikika kumafikira), wowongolera amazimitsa mpope.

• Kuchedwa kwa ntchito - ntchitoyi imalola wogwiritsa ntchito kukhazikitsa nthawi yochedwa yosinthira pampu kutentha kutsika pansi pa kutentha komwe kumayikidwa m'madera aliwonse. Kuchedwa kwakusintha papope kumagwiritsidwa ntchito kuti choyambitsa valavu chitseguke.

KUCHENJETSA - KUZIZIGIRITSA
Ntchitoyi imakupatsani mwayi wosankha njira yogwiritsira ntchito:

• Kutentha - madera onse amatenthedwa
• Kuzizira - madera onse aziziritsidwa
• Zodziwikiratu - wowongolera amasintha mawonekedwe pakati pa kutentha ndi kuziziritsa kutengera kuyika kwa mayiko awiri.

ZOKHUDZA ZOKHUDZA ZOYAMBIRA
Izi zimakakamiza kugwira ntchito kwa mapampu ndi mavavu (onani njira yoyamba), zomwe zimalepheretsa ma depositi a sikelo panthawi yakusagwira ntchito kwa mapampu ndi mavavu, mwachitsanzo kunja kwa nyengo yotentha. Ngati ntchitoyi yayatsidwa, mpope ndi mavavu amayatsa pa nthawi yoikika komanso ndi nthawi yodziwika (mwachitsanzo masiku 10 aliwonse kwa 5 min.).

KUCHULUKA KWAMBIRI
Ngati mulingo wa chinyezi wapano ndi wapamwamba kuposa chinyezi chokhazikika, kuziziritsa kwa zone kudzachotsedwa.

CHENJEZO
Ntchitoyi imangogwira ntchito mu Kuzizira, bola ngati sensor yokhala ndi chinyezi imalembetsedwa m'derali.

CHINENERO
Ntchitoyi imakulolani kuti musinthe chilankhulo cha olamulira.

Kutentha Pump
Njira yodzipatulira yoyikapo ntchito ndi pampu yotentha, kulola kugwiritsa ntchito bwino mphamvu zake.

• Njira yopulumutsira mphamvu - kuyika njirayo kudzayambitsa njirayo ndipo zosankha zambiri zidzawonekera.
• Nthawi yocheperako yopumira - chizindikiro chochepetsa kuchuluka kwa masinthidwe a kompresa, omwe amalola kukulitsa moyo wa kompresa. Mosasamala kanthu kofunikira kutenthetsanso gawo lomwe laperekedwa, kompresa idzayamba pokhapokha nthawi yowerengedwa kuchokera kumapeto kwa ntchito yapitayi itatha.
• Bypass - njira yofunikira pakalibe chotchingira, kupatsa pampu yotentha yokhala ndi kutentha koyenera. Zimadalira kutsegula motsatizana kwa madera otsatira nthawi iliyonse yodziwika.
  • Pampu yapansi - yambitsa / thimitsa mpope wapansi
  • Nthawi yozungulira - nthawi yomwe malo osankhidwa adzatsegulidwa.

ZOCHITIKA PA FACTORY

Ntchitoyi imakulolani kuti mubwerere ku zoikamo za fitter zomwe zasungidwa ndi wopanga.

SERVICE MENU
Menyu yautumiki wa oyendetsa imapezeka kwa anthu ovomerezeka okha ndipo imatetezedwa ndi khodi yaumwini ya Tech Sterowniki.

ZOCHITIKA PA FACTORY
Ntchitoyi imakulolani kuti mubwerere ku zosintha zosasinthika za wolamulira, monga momwe amafotokozera wopanga.

SOFTWARE VERSION
Izi zikatsegulidwa, chizindikiro cha wopanga chidzawonekera pachiwonetsero, pamodzi ndi nambala ya mtundu wa pulogalamu yowongolera. Kukonzanso kwa mapulogalamu kumafunika mukalumikizana ndi ntchito ya Tech Sterowniki.

Mndandanda wa ALARM

ZOCHITIKA ZA SOFTWARE

Kuti mukweze pulogalamu yatsopano, chotsani chowongolera pa netiweki. Lowetsani USB flash drive yomwe ili ndi pulogalamu yatsopano padoko la USB. Kenako gwirizanitsani chowongolera ku netiweki uku mukugwira batani la EXIT. Gwirani pansi batani la EXIT mpaka mumve bepu limodzi losonyeza kuyamba kwa pulogalamu yatsopano kutsitsa. Ntchitoyo ikamalizidwa, wowongolera amadziyambitsanso.

CHENJEZO

• Njira yoyika pulogalamu yatsopano kwa wowongolera imatha kuchitidwa ndi woyimitsa woyenerera. Pambuyo posintha pulogalamuyo, sizingatheke kubwezeretsa zoikamo zakale.
• Musati muzimitse chowongolera pamene mukukonza mapulogalamu.

ZINTHU ZAMBIRI

• Gulu la katundu wa AC1: gawo limodzi, loletsa kapena lowonjezera pang'ono AC katundu.
• Gulu la katundu wa DC1: katundu wamakono, wotsutsa kapena wowonjezera pang'ono.

KULENGEZA KWA EU KWA CONFORMITY

Apa, tikulengeza pansi pa udindo wathu kuti EU-LX WiFi yopangidwa ndi TECH STEROWNIKI II Sp. z oo, likulu ku Wieprz Biała Droga 31, 34-122 Wieprz, ikugwirizana ndi Directive 2014/53/EU ya European Parliament ndi Council of 16 April 2014 pakugwirizana kwa malamulo a Member States okhudza kupezeka pamsika wa zida zamawayilesi, Directive 2009/125/EC kukhazikitsa maziko okhazikitsa zofunikira za ecodesign pazinthu zokhudzana ndi mphamvu komanso kuwongolera ndi MINISTRY OF ENTREPRENEURSHIP AND TECHNOLOGY ya 24 June 2019 yosintha malamulo okhudza Zofunikira pakuletsa kugwiritsa ntchito zinthu zina zowopsa pazida zamagetsi ndi zamagetsi, kugwiritsa ntchito Directive (EU) 2017/2102 ya European Parliament ndi Council of 15 November 2017 yosintha Directive 2011/65/EU pa kuletsa kugwiritsa ntchito zinthu zina zowopsa pazida zamagetsi ndi zamagetsi (OJ L 305, 21.11.2017, p. 8).
Pakuwunika kutsata, miyezo yogwirizana idagwiritsidwa ntchito:

• Chithunzi cha PN-EN IEC 60730-2-9:2019-06 3.1a Chitetezo chogwiritsa ntchito
• Chithunzi cha PN-EN IEC 62368-1:2020-11 3.1 Chitetezo chogwiritsa ntchito
• PN-EN 62479: 2011 luso. 3.1 Chitetezo chogwiritsa ntchito
• ETSI EN 301 489-1 V2.2.3 (2019-11) art.3.1b Kugwirizana kwa Electromagnetic
• ETSI EN 301 489-3 V2.1.1 (2019-03) art.3.1 b Kugwirizana kwa Electromagnetic
• ETSI EN 301 489-17 V3.2.4 (2020-09) art.3.1b Kugwirizana kwa Electromagnetic
• ETSI EN 300 328 V2.2.2 (2019-07) art.3.2 Kugwiritsa ntchito moyenera komanso kogwirizana kwa ma radio sipekitiramu
• ETSI EN 300 220-2 V3.2.1 (2018-06) art.3.2 Kugwiritsa ntchito moyenera komanso kogwirizana kwa ma radio sipekitiramu
• ETSI EN 300 220-1 V3.1.1 (2017-02) art.3.2 Kugwiritsa ntchito moyenera komanso kogwirizana kwa ma radio sipekitiramu
• EN IEC 63000: 2018 RoHS

Likulu lapakati
ul. Biata Droga 31, 34-122 Wieprz

Utumiki
ul. Skotnica 120, 32-652 Bulowice

• foni: + 48 33 875 93 80
• imelo: serwis@techsterrowniki.pl
• www.tech-controllers.com

Zolemba / Zothandizira

Owongolera TECH EU-LX WiFi Floor Strip Controller [pdf] Buku Logwiritsa Ntchito EU-LX, EU-LX WiFi Floor Strip Controller, WiFi Floor Strip Controller, Floor Strip Controller, Strip Controller, Controller

Maumboni

• Buku Logwiritsa Ntchito