IRONBISON IB-CCS1-03 Front Bumper Installation Guide

Torque & Zvishandiso

90-180 min

Kucheka Hazvidiwi

Kuchera hakudiwi

Fastener Size	Kusimbisa Torque (ft-lbs)	Chipanera Chinodiwa		Allen Wrench Inodiwa
6mm	7-8.5		10mm		4mm
8mm	18-20		13mm		5mm
10mm	35-40		16mm		6mm
12mm	60-70		18mm		8mm
KUSATI KUISA Bvisa ZVIRI MUBHUKU. ONA ZVIKAMU ZVINHU ZVIRIPO ZVICHIENDERANA NEKURONGWA KWEZVIKAMU. VERENGA MIRAYIRIRO ZVAKANAKA Usati Watanga INSTALLATION. RUBATSIRO RUNOFARIRA KUNHU KUNHU ZVINHU ZVINOGONA KUKVARA KANA KUKVARWA KWEMOTORI.

Shandisa kubatanidza iyoFrame Bracket kutifuremu：	x8 12mm x 37mm x 3mm Flat Washer   x8 12mm Nylon x4 Kiya Nut x410mm x 30mm x 2.5mm Flat Washer x4 10mm Nylon Kiya Nut
Shandisa kubatanidza Bumper kune Frame Bracket:	x6 12mm x 40mm Hex Bolt x6 12mm Kiya Washer x6 12mm x 37mm x 3mm Flat Washer
Shandisa kubatanidza Center Mesh Zadza Panel kana LED Mwenje Bar kune iyo Bumper:	x4 8mm x 25mm Hex Bolt x8 8mm x 24mm x 2mm Flat Washer x4 8mm Kiya Washer
Shandisa kubatanidza iyoWings ku Bamper:	8mm x 20mm Hex Bolt 8mm x 16mm Flat Washe 8mm Flange Nut 6mm x 20mm Combo Bolt 6mm Flange Nut
Shandisa kubatanidza iyo LED Cube Chiedza Mabhureki uye Outer Mesh Zadza mapaneru kune iyo Bumper:	6mm x 20mm Combo Bolt 6mm Flange Nut
Shandisa kubatanidza License Plate Bracket kune Bumper:	x2 6mm x 20mm Bhatani Musoro Bolt x4 6mm x 18mm x 1.6mm Flat Washer x2 6mm Nylon Kiya Nut x1 4mm Allen Chipanera
Use to attachhjihjuuihyu8hu8hyu8yu8hy8y8y8y7gy7y7y76y766 theMasensa ekupaka akabatidzwaiyo Bumper：	x2 Sensor Cap x2 Furo Spacer x2 Foam Seal Wire Harness Extension x2 Sensor Hole Plastic plug (Shandisa pane mhando dzisina Front Sensor) x6 Sensor Cover (Fukidza sensor kana yatadza)

STEP 1Vhura hood uye bvisa chivharo chepurasitiki kubva kumusoro kwegrille uye radiator, (Mufananidzo 1).

Bvisa chivharo uye screws dzinobatanidza grille
Models ine grille yakaiswa kamera, unplug kamera. Tevere, bvisa screws inonamatira grille kune iyo radiator core support. Kana zvinhu zvese zvabviswa, dhonza grille wakananga kubva mumotokari kuti usunungure grille kubva pazvimedu, (Mufananidzo 2).

STEP 2
Bvisa rezinesi ndiro uye bracket. Pamhando dzine mwenje wefekitari uye/kana mabumper sensors, sunungura tambo yewaya inotungamira kune bumper, (Mufananidzo 3).

Kuburikidza nemufambi/kurudyi fender liner, sunungura wiring harness inoenda kumberi bumper (museve)
CHERECHEDZA: Wiring harness connector inowanikwa kumusoro uye kuseri kwemupfuuri/kurudyi kwebhampa. Sunungura zvimedu zvinobatanidza mufambi/kurudyi fender liner kuti uwane plug ye harness. Bvisa harness kure nebumper.
STEP 3
Kubva kuseri kwemutyairi/kuruboshwe kwebhampa, bvisa Hardware inosungirira yekunze bumper rutsigiro kudivi rekumucheto kwekunze kwebumper, (Mufananidzo 4).

Bvisa hardware inosungirira kunze kwekutsigira bracket kune bumper (museve)
STEP 4
Tsvaga uye bvisa mabhaudhi ehex anosungira pasi pebumper kune bumper bracket yakasungirirwa kumagumo efuremu, (Mufananidzo 5).

Bvisa pasi bumper zvinotsigira (museve) 

STEP 5
Dzokorora Matanho 3 & 4 kuti ubvise hardware inosungirira bumper kumufambi / kurudyi bumper rutsigiro uye yakaderera bumper bracket.

STEP 6
Dzokera kumusoro kwebumper. Dhonza kumashure kumagumo evhavha yerabha pakati pebhampa neradiyeta kuratidza mabhaudhi anonamira pamusoro pebhuraketi kubhureki yeframe, (Mufananidzo 6).

Dhonza chivharo chekumashure kuti uwane mabhaudhi epamusoro
STEP 7
Isa mabhuraki kana majeko anomira pasi pebhampa yekumberi kuti utsigire panguva yekukwira kubviswa kwebhaudhi. Kana bumper yave yakatsigirwa zvakachengeteka, kubva kumusoro, bvisa mabhaudhi anosungirira musangano webumper kumusoro kwebhuraketi, (Mufananidzo 6).
YAMBIRO! Rubatsiro runodiwa kubata bumper panzvimbo panguva yekubviswa kwebhaudhi kudzivirira kuti bumper isadonha. Nyatsotsveta bumper assembly nemabhuraketi kubva kumagumo efuremu.
YAMBIRO! Usakambaire nepasi pebumper kunze kwekunge yanyatso tsigirwa pamabhuroko kana mastand kana bumper ikadonha.

STEP 8
Bvisa zvikorekedzo zviviri kubva kumagumo efuremu kana aine, (Mufananidzo 7)

Bvisa hoko dzekudhonza kana uine
STEP 9
Sarudza mutyairi / kuruboshwe Frame Bracket, (Mufananidzo 8).

Shandisa (1) Left Offset uye (1) Right Offset Triple Bolt Plates kubatanidza mutyairi/kuruboshwe Frame Bracket pafuremu.
Svetedza Bracket kumucheto kwefuremu. Isa (1) Left Offset Triple Bolt Plate kumucheto kwefuremu uye kunze nemaburi ari padivi pefuremu uye Chibhuraketi Chekukwirisa.

CHERECHEDZA: Imwe neimwe yeMounting Bracket inoda (1) Left Offset uye (1) Right Offset Bolt Plate yekuisa.

STEP 10
Natanidza Bracket Kuruboshwe Offset Bolt Plate ine inosanganisirwa (2) 12mm Flat Washers, (2) 12mm Nylon Lock Nuts, (1) 10mm Flat Washer uye (1) 10mm Nylon Lock Nut, (Mufananidzo 8). Dzokorora kuisa (1) Kurudyi Offset Bolt Plate mumakomba ekurangarira kune rimwe divi reFremu Bracket, (Mufananidzo 9).

Mutyairi/kuruboshwe Frame Bracket yakaiswa
(Mufananidzo 8) Shandisa (1) Left Offset uye (1) Right Offset Triple Bolt Plates kubatanidza mutyairi/kuruboshwe Frame Bracket pafuremu.
(Mufananidzo 9) Mutyairi/kuruboshwe Frame Bracket yakaiswa

STEP 11
Dzokorora Matanho 9 & 10 kuti ubatanidze mufambi / kurudyi Frame Mounting Bracket.

STEP 12
Bvisa dhamu remhepo. Disassemble bumper yefekitori kuti ubvise yakaderera bumper yekuzadza pani, (Mufananidzo 10).

Disassemble front bumper assembly kuti ubvise yakadzika bumper insert (museve)
CHERECHEDZA: Mhepo dhamu uye mapaneru ekuzadza hazvizogadzirwe zvakare.

STEP 13
Sarudza kana bumper ine ma sensors ekupaka pamberi.

Models isina sensors:

a. Sunda iyo inosanganisirwa (2) Sensor Hole Plastic Plugs mumakomba ema sensors, (Mufananidzo 11) Enda kuNhanho 14. Mienzaniso ine ma sensor ekupaka.
a. Bvisa uye bvisa (2) masensa epakati kubva pafekitari bumper.
b. Sarudza (1) sensor. Bvisa chisimbiso chesilicone kubva kumagumo e sensor. Svetera iyo inosanganisirwa yakakura Foam Chisimbiso pamberi pe sensor, (Mufananidzo 12).
c. Isa sensor ine Chisimbiso mune sensor gomo pane hoop paBumper, (Fig 13).
d. Isa Foam Spacer kumagumo e sensor. Push Sensor Cap uye svetukira pagomo re sensor, (Fig 13).

Mamodheru asina masensa, isa maPlug ePurasitiki mumasenso anokwirisa paBumper Hoop

(Mufananidzo 12) Bvisa chepakutanga silicone chisimbiso kubva ku sensor. Slide yaisanganisira Foam Seal pamusoro pekupedzisira kwe sensor

(Mufananidzo 13) Sunda Sensor Cap mune inokwirisa sleeve

STEP 14
Unganidzazve bumper yefekitari. Pamhando dzine masensa, sarudza (1) Wire Harness Extension. Sunda Iyo Harness Extension kuburikidza ne sensor gomba pakati pefekitari bumper uye plug mukati memukati wefekitari harness. Dzokorora kuisa yasara Harness Extension.

STEP 15

Sarudza kana mwenje wefekitari, (kana akashongedzerwa), mwenje we LED Cube, (isina kuisirwa), kana pasina mwenje ichaiswa neBumper.

Mamodheru ane uye anoshandisa zvakare fekitori fog lights:

a. Siya marambi emhute akabatanidzwa papurasitiki gomo mwanakomana kumashure kwefekitari bumper, (Fig 14).
b. Dzorera bumper yefekitari. Cube style LED mwenje kuisirwa (isina kuisirwa):
a. Bvisa mwenje wefekitari, (kana wakashongedzerwa), kubva kumamoiri ari kumashure kwefekitori bumper, (Mufananidzo 15).
b. Sarudza mutyairi / kuruboshwe LED Cube Chiedza Bracket, (Fig 16). Namatidza Bracket kuseri kweBumper ine inosanganisirwa (5) 6mm x 20mm Combo Bolts uye (5) 6mm Flange Nuts.
c. Batanidza Cube Chiedza (Isina Kusanganisirwa) kune tebhu pamusoro peKukwidza Bracket.
d. Dzokorora Matanho apfuura kuti uise mutakuri/kurudyi cube light Bracket uye chiedza.
e. CHERECHEDZA: Kana marambi akasaiswa, batanidza anosanganisirwa (2) Mesh Zadza mapaneru kuCube Chiedza Mabhureki ane (4) 6mm x 20mm Combo Bolts uye (4) 6mm Flange Nuts, (Mufananidzo 17).

STEP 16
Sarudza kana nzvimbo 20 ”LED light bar, (isina kusanganisirwa), kana Mesh Zadza Panel ichaiswa. Center 20” LED mwenje bhari yekuisa (chiedza chisina kuisirwa).

a. Sarudza iyo (2) "L" mabhureki e LED, (Fig 18). Natanidza Mabhureki kune (2) ma tabhu anokwirisa kuseri kwebhampa ane anosanganisirwa (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers uye (2) 8mm Hex Nuts. . Ibva wakasununguka panguva ino.
b. Batanidza mwenje we LED kune "L" Mabhureki e LED ane hardware inosanganisirwa nemwenje kana inosanganisirwa (2) 8mm x 16mm Hex Bolts, (2) 8mm Lock Washers uye (2) 8mm x 24mm Flat Washers, (Fig 18) . Usaomesa zvizere hardware panguva ino.
c. Tevedzera mirairo yemugadziri wemwenje kuti wayaye mwenje zvakanaka.

Center Mesh Zadza Panel Kuiswa (usaise Zadza Panel nechiedza).

a. Dzokorora Nhanho yapfuura kuti uise (2) "L" Mabhureki e LED.
b. Batanidza iyo Center Mesh Zadza Panel kune iyo "L" LED Mabhureki ane anosanganisirwa (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers uye (2) 8mm Hex Nuts, (Mufananidzo 19).
c. Push Zadza Panel kumusoro kuseri kweBumper uye simbisa zvakazara hardware.

(Mufananidzo 18) Batanidza "L" Mabhureki e LED kana uchiisa LED centre mwenje (isina kuisirwa) kana Center Mesh Zadza Panel.
Natanidza Rezinesi Plate Bracket kuBumperSTEP 18
Kana rezinesi remberi richidikanwa, batanidza Rezinesi Plate Chibhuraketi kumakomba ari muBumper ine inosanganisirwa (2) 6mm x 20mm Button Head Screws, (4) 6mm Flat Washers uye (2) 6mm Nylon Lock Nuts. Isa (2) Square Plastic Plugs mumakomba akaenzana muBracket, (Fig 21). Shandisazve masiruuru efekitari kubatanidza rezinesi plate kuSquare Plastic Plugs.

STEP 20
Dzorerazve grille yepurasitiki, kamera kana yakashongedzerwa uye chivharo chakabviswa muChikamu chekutanga, (Mufananidzo 1).

STEP 21
Isa Bumper yakatarisa pasi pamberi pemotokari. Mamodheru ane masensa, plug iyo Wire Harness Extensions mu (2) sensors muBumper, (Mufananidzo 22).

(Mufananidzo 22) Models dzine masensa, plug Wire Harness Extensions (ona Nhanho 14) pafekitari bumper mumasensa akaiswa paBumper.

YAMBIRO! Usakambaire nepasi pebumper kunze kwekunge yanyatso tsigirwa pamabhuroko kana mastand kana bumper ikadonha.

STEP 23
Rongedza (3) mitsetse yemutyairi/kuruboshwe rwekukwirisa ndiro kuseri kweBumper neFreme Bracket. Isa (1) "T" Nut Plate kumashure kweFremu Bracket, (Mufananidzo 23). Natanidza Bumper kune Frame Bracket uye “T” Nut Plate ine inosanganisirwa (3) 12mm Hex Bolts, (3) 12mm Lock Washers uye (3) 12mm Flat Washers, (Mufananidzo 24). Dzokorora kuti ubatanidze mufambi/rudyi.

(Mufananidzo 24) Mutyairi/kuruboshwe rweBumper yakasungirirwa kuFrame Bracket (Cherechedza cube light installation)

STEP 25
Sarudza mutyairi/kuruboshwe Lower Wing. Natanidza Bapiro kumagumo eBumper ne (1) 8mm x 20mm Hex Bolt, (1) 8mm x 16mm Diki Flat Washer uye (1) 8mm Flange Nut, (Mifananidzo 25 & 26). Natanidza kumusoro kweBapiro kuzasi kwefekitori bumper ine inosanganisirwa (2) 6mm Bhatani Musoro Combo Bolts uye (2) 6mm Flange Nuts, (Mufananidzo 26). Dzokorora Danho iri kuti ubatanidze mupfuuri/kurudyi Lower Wing kune Bumper.

(Mufananidzo 26) Batanidza mutyairi/kuruboshwe Lower Bumper "Wing" kusvika kumagumo kweBumper uye pasi pefekitori bumper. Kuiswa kunoratidzwa kubva kuseri kwebhampa

(Mufananidzo 27) Kuisirwa kwakazara (20 ”Kaviri Row Chiedza Bar uye maviri maLED Cube Mwenje haana kuisirwa)

STEP 26
Ita ongororo nguva nenguva kune yekumisikidza kuti uve nechokwadi chekuti hardware yese yakachengeteka uye yakasimba.

IRONBISON IB-CCS1-03 Front Bumper Installation Guide

Torque & Zvishandiso

Chikamu List

STEP 1
Vhura hood uye bvisa chivharo chepurasitiki kubva kumusoro kwegrille uye radiator, (Mufananidzo 1). Models ine grille yakaiswa kamera, unplug kamera. Tevere, bvisa screws inonamatira grille kune iyo radiator core support. Kana zvinhu zvese zvabviswa, dhonza grille wakananga kubva mumotokari kuti usunungure grille kubva pazvimedu, (Mufananidzo 2). Isa grille panzvimbo yakachena, yakapfava.
(Fig 1) Bvisa chivharo uye screws dzinobatanidza grille
(Fig 2) Dhonza grille zvakasimba kubva mumotokari

STEP 2
Bvisa rezinesi ndiro uye bracket. Pamhando dzine mwenje wefekitari uye/kana mabumper sensors, sunungura tambo yewaya inotungamira kune bumper, (Mufananidzo 3).
CHERECHEDZA: Wiring harness connector inowanikwa kumusoro uye kuseri kwemupfuuri/kurudyi kwebhampa. Sunungura zvimedu zvinobatanidza mufambi/kurudyi fender liner kuti uwane plug ye harness. Bvisa harness kure nebumper.
(Fig 3) Kuburikidza nemufambi/kurudyi fender liner, sunungura wiring harness inoenda kumberi bumper (museve)

STEP 3
Kubva kuseri kwemutyairi/kuruboshwe kwebhampa, bvisa Hardware inosungirira yekunze bumper rutsigiro kudivi rekumucheto kwekunze kwebumper, (Mufananidzo 4).
(Fig 4) Bvisa hardware inosungirira kunze kwekutsigira bracket kune bumper (museve)

STEP 4
Tsvaga uye bvisa mabhaudhi ehex anosungira pasi pebumper kune bumper bracket yakasungirirwa kumagumo efuremu, (Mufananidzo 5).
(Fig 5) Bvisa pasi bumper inotsigira (museve) 

STEP 5
Dzokorora Matanho 3 & 4 kuti ubvise hardware inosungirira bumper kumufambi / kurudyi bumper rutsigiro uye yakaderera bumper bracket.

STEP 6
Dzokera kumusoro kwebumper. Dhonza kumashure kumagumo evhavha yerabha pakati pebhampa neradiyeta kuratidza mabhaudhi anonamira pamusoro pebhuraketi kubhureki yeframe, (Mufananidzo 6).
(Fig 6) Dhonza chivharo chekumashure kuti uwane mabhaumu epamusoro

STEP 7
Isa mabhuraki kana majeko anomira pasi pebhampa yekumberi kuti utsigire panguva yekukwira kubviswa kwebhaudhi. Kana bumper yave yakatsigirwa zvakachengeteka, kubva kumusoro, bvisa mabhaudhi anosungirira musangano webumper kumusoro kwebhuraketi, (Mufananidzo 6).

YAMBIRO! Rubatsiro runodiwa kubata bumper panzvimbo panguva yekubviswa kwebhaudhi kudzivirira kuti bumper isadonha. Nyatsotsveta bumper assembly nemabhuraketi kubva kumagumo efuremu.

YAMBIRO! Usakambaire nepasi pebumper kunze kwekunge yanyatso tsigirwa pamabhuroko kana mastand kana bumper ikadonha.

STEP 8
Bvisa zvikorekedzo zviviri kubva kumagumo efuremu kana aine, (Mufananidzo 7)
(Fig 7) Bvisa zvikorekedzo zvekudhonza kana uine 

STEP 9
Sarudza mutyairi / kuruboshwe Frame Bracket, (Mufananidzo 8). Svetedza Bracket kumucheto kwefuremu. Isa (1) Left Offset Triple Bolt Plate kumucheto kwefuremu uye kunze nemaburi ari padivi pefuremu uye Chibhuraketi Chekukwirisa.

CHERECHEDZA: Imwe neimwe yeMounting Bracket inoda (1) Left Offset uye (1) Right Offset Bolt Plate yekuisa.

STEP 10
Natanidza Bracket Kuruboshwe Offset Bolt Plate ine inosanganisirwa (2) 12mm Flat Washers, (2) 12mm Nylon Lock Nuts, (1) 10mm Flat Washer uye (1) 10mm Nylon Lock Nut, (Mufananidzo 8). Dzokorora kuisa (1) Kurudyi Offset Bolt Plate mumakomba ekurangarira kune rimwe divi reFremu Bracket, (Mufananidzo 9).

(Mufananidzo 8) Shandisa (1) Left Offset uye (1) Right Offset Triple Bolt Plates kubatanidza mutyairi/kuruboshwe Frame Bracket pafuremu.
(Mufananidzo 9) Mutyairi/kuruboshwe Frame Bracket yakaiswa

STEP 11
Dzokorora Matanho 9 & 10 kuti ubatanidze mufambi / kurudyi Frame Mounting Bracket.

STEP 12
Bvisa dhamu remhepo. Disassemble bumper yefekitori kuti ubvise yakaderera bumper yekuzadza pani, (Mufananidzo 10).

CHERECHEDZA: Mhepo dhamu uye mapaneru ekuzadza hazvizogadzirwe zvakare.

STEP 13
Sarudza kana bumper ine ma sensors ekupaka pamberi.

Models isina sensors:

a. Sunda iyo inosanganisirwa (2) Sensor Hole Plastic Plugs mumakomba ema sensors, (Mufananidzo 11).

Disassemble front bumper assembly kuti ubvise yakadzika bumper insert (museve)
Enda kuNhanho 14. Mienzaniso ine ma sensor ekupaka.
a. Bvisa uye bvisa (2) masensa epakati kubva pafekitari bumper.
b. Sarudza (1) sensor. Bvisa chisimbiso chesilicone kubva kumagumo e sensor. Svetera iyo inosanganisirwa yakakura Foam Chisimbiso pamberi pe sensor, (Mufananidzo 12).

Bvisa chepakutanga silicone chisimbiso kubva ku sensor. Slide yaisanganisira Foam Seal pamusoro pekupedzisira kwe sensor
c. Isa sensor ine Chisimbiso mune sensor gomo pane hoop paBumper, (Mufananidzo 13).
d. Isa Foam Spacer kumagumo e sensor. Push Sensor Cap uye sveta pagomo re sensor, (Mufananidzo 13)
Sunda Sensor Cap mune inokwirisa sleeve

STEP 14
Unganidzazve bumper yefekitari. Pamhando dzine masensa, sarudza (1) Wire Harness Extension. Sunda Iyo Harness Extension kuburikidza ne sensor gomba pakati pefekitari bumper uye plug mukati memukati wefekitari harness. Dzokorora kuisa yasara Harness Extension.

STEP 15
Sarudza kana mwenje wefekitari, (kana akashongedzerwa), mwenje we LED Cube, (isina kuisirwa), kana pasina mwenje ichaiswa neBumper.

Mamodheru ane uye anoshandisa zvakare fekitori fog lights:

a. Siya marambi emhute akasungirirwa papurasitiki gomo mwanakomana kumashure kwefekitari bumper, (Mufananidzo 14).

Unganidzazve bumper pasina yakadzika bhamper kupinza. Kumashure kwemutyairi/kuruboshwe rwemodhi ine fog light inoratidzwa
b. Dzorera bumper yefekitari. Cube style LED mwenje kuisirwa (isina kuisirwa):
a. Bvisa mwenje wefekitari, (kana wakashongedzerwa), kubva kumamoiri ari kumashure kwefekitori bumper, (Mufananidzo 15).

Bvisa fekitori fog light kana ukaisa LED cube style marambi kana Mesh Zadza Panels
b. Sarudza mutyairi/kuruboshwe LED Cube Chiedza Bracket, (Mufananidzo 16).

Isa mutyairi/kuruboshwe LED cube light Bracket
Namira Bracket kuseri kweBumper ine inosanganisirwa (5) 6mm x 20mm Combo Bolts uye (5) 6mm Flange Nuts.
c. Batanidza Cube Chiedza (Isina Kusanganisirwa) kune tebhu pamusoro peKukwidza Bracket.
d. Dzokorora Matanho apfuura kuti uise mutakuri/kurudyi cube light Bracket uye chiedza.
e. CHERECHEDZA: Kana marambi akasaiswa, batanidza anosanganisirwa (2) Mesh Zadza mapaneru kuCube Chiedza Mabhureki ane (4) 6mm x 20mm Combo Bolts uye (4) 6mm Flange Nuts, (Mufananidzo 17).

 Batanidza Zadza Panel kune Chiedza Bracket kana pasina mwenje uchaiswa
STEP 16
Sarudza kana nzvimbo 20 ”LED light bar, (isina kusanganisirwa), kana Mesh Zadza Panel ichaiswa. Center 20” LED mwenje bhari yekuisa (chiedza chisina kuisirwa).

a. Sarudza iyo (2) "L" LED mabhureki, (Mufananidzo 18).

Batanidza "L" Mabhureki e LED kana uchiisa LED centre mwenje (isina kuisirwa) kana Center Mesh Zadza Panel.
Natanidza Mabhureki kune (2) ma tabhu anokwirisa kuseri kwebhampa ane anosanganisirwa (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers uye (2) 8mm Hex Nuts. . Siya wakasununguka panguva ino.
b. Batanidza mwenje we LED kune "L" Mabhureki e LED ane hardware inosanganisirwa nemwenje kana iyo inosanganisirwa (2) 8mm x 16mm Hex Bolts, (2) 8mm Lock Washers uye (2) 8mm x 24mm Flat Washers, (Mufananidzo 18). Usaomesa zvizere hardware panguva ino.
c. Tevedzera mirairo yemugadziri wemwenje kuti wayaye mwenje zvakanaka.

Center Mesh Zadza Panel Kuiswa (usaise Zadza Panel nechiedza).

a. Dzokorora Nhanho yapfuura kuti uise (2) "L" Mabhureki e LED.
b. Batanidza iyo Center Mesh Zadza Panel kune iyo "L" LED Mabhureki ane anosanganisirwa (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers uye (2) 8mm Hex Nuts, (Mufananidzo 19).

Batanidza Center Mesh Zadza Panel ku "L" LED Mabhureki (Usaise Zadza Panel nemwenje we LED)
c. Push Zadza Panel kumusoro kuseri kweBumper uye simbisa zvakazara hardware.

STEP 17
Batanidza iyo inosanganisirwa Edge Trim kumucheto wepamusoro weBumper, (Mufananidzo 20).

Isa Rubber Trim kumucheto kweBumper

STEP 18
Kana rezinesi remberi richidikanwa, batanidza Rezinesi Plate Chibhuraketi kumakomba ari muBumper ine inosanganisirwa (2) 6mm x 20mm Button Head Screws, (4) 6mm Flat Washers uye (2) 6mm Nylon Lock Nuts. Isa (2) Square Plastic Plugs mumakomba akaenzana muBracket, (Fig 21). Shandisazve masiruuru efekitari kubatanidza rezinesi plate kuSquare Plastic Plugs.

Natanidza Rezinesi Plate Bracket kuBumper

STEP 20
Dzorerazve grille yepurasitiki, kamera kana yakashongedzerwa uye chivharo chakabviswa muChikamu chekutanga, (Mufananidzo 1).

STEP 21
Isa Bumper yakatarisa pasi pamberi pemotokari. Mamodheru ane masensa, plug iyo Wire Harness Extensions mu (2) sensors muBumper, (Mufananidzo 22).

Models dzine masensa, plug Wire Harness Extensions (ona Nhanho 14) pafekitari bumper mumasensa akaiswa paBumper.

YAMBIRO: Kuti udzivise kukuvara kana kukuvara kwemotokari, usaenderere mberi kusvika Bumper yanyatsotsigirwa uye yakachengeteka.
YAMBIRO! Usakambaire nepasi pebumper kunze kwekunge yanyatso tsigirwa pamabhuroko kana mastand kana bumper ikadonha.

STEP 23
Rongedza (3) mitsetse yemutyairi/kuruboshwe rwekukwirisa ndiro kuseri kweBumper neFreme Bracket. Isa (1) "T" Nut Plate kumashure kweFremu Bracket, (Mufananidzo 23). Natanidza Bumper kune Frame Bracket uye “T” Nut Plate ine inosanganisirwa (3) 12mm Hex Bolts, (3) 12mm Lock Washers uye (3) 12mm Flat Washers, (Mufananidzo 24).

Mutyairi/kuruboshwe rweBumper yakasungirirwa kuFrame Bracket (Cherechedza cube light installation)
Dzokorora kuti ubatanidze mufambi/rudyi.

STEP 25
Sarudza mutyairi/kuruboshwe Lower Wing. Natanidza Bapiro kumagumo eBumper ne (1) 8mm x 20mm Hex Bolt, (1) 8mm x 16mm Diki Flat Washer uye (1) 8mm Flange Nut, (Mifananidzo 25 & 26). Natanidza kumusoro kweBapiro kuzasi kwefekitori bumper ine inosanganisirwa (2) 6mm Bhatani Musoro Combo Bolts uye (2) 6mm Flange Nuts, (Mufananidzo 26). Dzokorora Danho iri kuti ubatanidze mupfuuri/kurudyi Lower Wing kune Bumper.
c
(Fig 25) Batanidza mutyairi/kuruboshwe Lower Bumper “Wing” kumagumo eBumper uye pasi pefekitori bumper (miseve)

(Mufananidzo 26) Batanidza mutyairi/kuruboshwe Lower Bumper "Wing" kusvika kumagumo kweBumper uye pasi pefekitori bumper. Kuiswa kunoratidzwa kubva kuseri kwebhampa

(Mufananidzo 27) Kuisirwa kwakazara (20 ”Kaviri Row Chiedza Bar uye maviri maLED Cube Mwenje haana kuisirwa)

STEP 26
Ita ongororo nguva nenguva kune yekumisikidza kuti uve nechokwadi chekuti hardware yese yakachengeteka uye yakasimba.

www.ironbisonauto.com Peji 10 ye10 Zvak. 6/27/23 (JH)

Zvinyorwa / Zvishandiso

IRONBISON IB-CCS1-03 Front Bumper [pdf] Installation Guide IB-CCS1-03, IB-CCS1-03 Bhampa Mberi, Bhampa Mbero, Bhampa

References

• User Manual