IRONBISON IB-CCS1-03 Front Bumper Installation Guide

Torque & Zida

90-180 min

Kudula Sikofunikira

Kubowola Sikofunikira

Kukula kwa Fastener	Kulimbitsa Torque (ft-lbs)	Wrench Yofunika		Allen Wrench Yofunika
6 mm	7-8.5		10 mm		4 mm
8 mm	18-20		13 mm		5 mm
10 mm	35-40		16 mm		6 mm
12 mm	60-70		18 mm		8 mm
MUSAMAIWE CHOTSANI ZILI PABOKSI. TSIMETSANI MAGAWA ONSE ALIPO MADALIRA NDI MTANDA WA MAGAWO. WERENGANI MALANGIZO MOCHEMWA MUSANAYAMBIRE KUYEKA. ZOTHANDIZA ZIKUYAMBIDWA KWAMBIRI KUPEWELA KUBWEKA KAPENA KUWONONGA GALIMOTO MUNGACHITE.

Gwiritsani ntchito kulumikizaFrame Bracket tochimango：	x8 12mm x 37mm x 3mm Washer Woyatsira   x8 12mm Nylon x4 Lock Mtedza x410mm x 30mm x 2.5mm Wasit Flat x4 10mm nayiloni Tsekani Nut
Gwiritsani ntchito kulumikiza Bumper ku Chimake cha chimango:	x6 12mm x 40mm Hex Bolt x6 12mm loko Washer x6 12mm x 37mm x 3mm Wasit Flat
Gwiritsani ntchito kulumikiza Center Mesh Fill Panel kapena LED Light Bar ku Bumper:	x4 8mm x 25mm Hex Bolt x8 8mm x 24mm x 2mm Wasit Flat x4 8mm loko Washer
Gwiritsani ntchito kulumikizaMapiko ku Bampa:	8mm x 20mm Hex Bolt 8mm x 16mm Flat Washe 8 mm kutalika Mtedza 6mm x 20mm Combo Bolt 6 mm kutalika Mtedza
Gwiritsani ntchito kulumikiza ma Bracket a LED Cube Light ndi Outer Mesh Fill Panels ku Bumper:	6mm x 20mm Combo Bolt 6 mm kutalika Mtedza
Gwiritsani ntchito kulumikiza License Plate Bracket ku Bumper:	x2 6mm x 20mm Batani Mutu Bolt x4 6mm x 18mm x 1.6mm Wasit Flat x2 6mm nayiloni Tsekani Nut x1 4 mm Ali Wrench
Use to attachhjihjuuihyu8hu8hyu8yu8hy8y8y8y7gy7y7y76y766 theMasensa oyimitsa magalimoto akuyatsidwandi Bumper：	x2 Sensor Cap x2 Chithovu Spacer x2 Chisindikizo cha Foam Wire Harness Extension x2 Pulagi ya Sensor Hole Plastic (Gwiritsani ntchito pa zitsanzo zopanda Front Sensor) x6 Chophimba cha Sensor (Phimbani sensor ikalephera)

CHOCHITA 1Tsegulani hood ndikuchotsa chivundikiro cha pulasitiki pamwamba pa grill ndi radiator, (Mkuyu 1)

Chotsani chivundikiro ndi zomangira zomangira grille
Ma Model okhala ndi kamera yokhala ndi grille, chotsani kamera. Kenako, chotsani zomangira zomangira grille ku chithandizo chapakati cha radiator. Zida zonse zikachotsedwa, kokerani grille molunjika kuchokera mgalimoto kuti mutulutse grille pazigawo, (Mkuyu 2)

CHOCHITA 2
Chotsani mbale ya layisensi ndi bulaketi. Pamitundu yokhala ndi nyali zachifunga za fakitale ndi/kapena masensa a bamper, masulani chingwe cholowera ku bampa, (Mkuyu 3)

Kupyolera pa mpanda/chotchinga chakumanja, chotsani chingwe cholumikizira cholowera kutsogolo (muvi)
ZINDIKIRANI: Cholumikizira cholumikizira mawaya chili mmwamba ndi kumbuyo kwa wokwera / kumanja kwa bampa. Tulutsani zomata zomangirira liner yonyamula anthu / kumanja kuti mulowetse pulagi ya zingwe. Chotsani zida kutali ndi bumper.
CHOCHITA 3
Kuchokera kuseri kwa dalaivala / kumanzere kwa bumper, chotsani zida zomangira chothandizira chakunja chakunja kwa bamper, (Mkuyu 4)

Chotsani zida zomangirira bulaketi yakunja yothandizira ku bumper (muvi)
CHOCHITA 4
Pezani ndi kuchotsa mabawuti a hex omwe akumangirira pansi pa bumper ku bumper bracket yomwe ili kumapeto kwa chimango, (Mkuyu 5).

Chotsani mabampu apansi (muvi) 

CHOCHITA 5
Bwerezani masitepe 3 & 4 kuti muchotse cholumikizira cholumikizira cholumikizira chokwera / chothandizira bampu yakumanja ndi bulaketi yotsika.

CHOCHITA 6
Bwererani pamwamba pa bamper. Kokani kumapeto kwa chivundikiro cha mphira pakati pa bampa ndi radiator kuti muwonetse mabawuti omwe amangiriza pamwamba pa bulaketi ku bulaketi ya chimango, (Mkuyu 6)

Kokani chophimba chakumbuyo kuti mupeze mabampu apamwamba
CHOCHITA 7
Ikani midadada kapena ma jeki pansi pa bampu yakutsogolo kuti muyichirikize pakuchotsa bawuti. Chingwecho chikathandizidwa bwino, kuchokera pamwamba, chotsani mabampu omangirira gululo pamwamba pa bulaketi, (Mkuyu 6)
CHENJEZO! Thandizo likufunika kuti chotchingira chikhale pamalo pochotsa bawuti kuti chotchinga chisagwe. Mosamala tsitsani chophatikizira chachikulu chokhala ndi mabulaketi kuchokera kumapeto kwa chimango.
CHENJEZO! Osakwawa pansi pa bumper pokhapokha ngati itakhazikika bwino pa midadada kapena ma stand kapena bampa itagwa.

CHOCHITA 8
Chotsani mbedza zonse ziwiri kumapeto kwa chimango ngati zili ndi zida, (Mkuyu 7)

Chotsani zingwe zokokera ngati zili ndi zida
CHOCHITA 9
Sankhani dalaivala / kumanzere Frame Bracket, (Mkuyu 8)

Gwiritsani ntchito (1) Kumanzere Kumanzere ndi (1) Kumanja Kumapeto kwa Maboti Katatu kuti muphatikize dalaivala/ Bracket yamanzere pa chimango
Tsegulani Bracket kumapeto kwa chimango. Lowetsani (1) Puleti ya Bolt Yakumanzere Kumapeto kwa chimango ndi kutuluka m'mabowo a m'mbali mwa chimango ndi Bracket Yokwera.

ZINDIKIRANI: Chingwe Chokwera Chilichonse chidzafuna (1) Kumanzere Kumanzere ndi (1) Kumanja kwa Bolt Plate kuti akhazikitse.

CHOCHITA 10
Gwirizanitsani Bracket ku Left Offset Bolt Plate ndi zophatikizira (2) 12mm Zochapira Zophwathira, (2) 12mm Mtedza wa Nayiloni wa 1mm, (10) 1mm Wochapira Wophwatsuka ndi (10) XNUMXmm Nylon Lock Nut, (Mkuyu 8). Bwerezani kuti muyike (1) Kumanja kwa Bolt Plate mumabowo okumbukira mbali ina ya Bracket ya Frame, (Mkuyu 9)

Bracket ya Dalaivala / kumanzere kwa Frame yayikidwa
(Mkuyu 8) Gwiritsani ntchito (1) Kumanzere Kumanzere ndi (1) Kumanja Kumapeto kwa Maboti Katatu kuti muphatikize dalaivala/ Bracket yamanzere pa chimango
(Mkuyu 9) Bracket ya Dalaivala / kumanzere kwa Frame yayikidwa

CHOCHITA 11
Bwerezani masitepe 9 & 10 kuti muphatikize wokwera / kumanja kwa Bracket Mounting Bracket.

CHOCHITA 12
Chotsani damu la mpweya. Phatikizani bumper ya fakitale kuti muchotse chodzaza chocheperako, (Mkuyu 10)

Phatikizani gulu lakutsogolo kuti muchotse choyikapo chocheperako (muvi)
ZINDIKIRANI: Damu la mpweya ndi gulu lodzaza madzi sizingakhazikitsidwenso.

CHOCHITA 13
Dziwani ngati bumper ili ndi masensa oimika magalimoto akutsogolo.

Mitundu yopanda masensa:

a. Kankhani zophatikizidwa (2) Mapulagi a Sensor Hole Pulasitiki m'mabowo a masensa, (Mkuyu 11). Pitani ku Gawo 14. Ma Model okhala ndi masensa oyimitsa magalimoto.
a. Chotsani ndi kuchotsa (2) masensa apakati pa bumper ya fakitale.
b. Sankhani (1) sensor. Chotsani chisindikizo cha silicone kuchokera kumapeto kwa sensa. Tsegulani Foam Seal yayikulu yophatikizidwa kutsogolo kwa sensor, (Mkuyu 12).
c. Lowetsani sensa yokhala ndi Seal mu sensor mount pa hoop pa Bumper, (Chithunzi 13).
d. Ikani Foam Spacer kumapeto kwa sensa. Kanikizani Sensor Cap ndikujambula pa chokwera cha sensor, (Chithunzi 13).

Mitundu yopanda masensa, ikani Mapulagi a Pulasitiki muzokwera za sensa pa Bumper Hoop

(Mkuyu 12) Chotsani chisindikizo choyambirira cha silikoni ku sensa. Slide idaphatikizanso Foam Seal kumapeto kwa sensor

(Mkuyu 13) Kankhani Sensor Cap mu manja okwera

CHOCHITA 14
Sonkhanitsaninso bumper ya fakitale. Pamitundu yokhala ndi masensa, sankhani (1) Wire Harness Extension. Kanikizani Zowonjezera Zowonjezera kudzera pa bowo loyikira sensa pakati pa bampa ya fakitale ndikulumikiza cholumikizira chamkati cha fakitale. Bwerezani kuti muyike Zowonjezera Zomangira zotsalira.

CHOCHITA 15

Dziwani ngati magetsi akufakitale, (ngati ali ndi zida), magetsi a LED Cube, (osaphatikizidwe), kapena ngati palibe magetsi omwe adzayikidwe ndi Bumper.

Mitundu yokhala ndi ndikugwiritsanso ntchito nyali zachifunga za fakitale:

a. Siyani nyali zachifunga zolumikizidwa ku pulasitiki wokwera mwana kumbuyo kwa bampa ya fakitale, (Mkuyu 14).
b. Ikaninso bampu yafakitale. Kuyika kwamtundu wa Cube LED kuwala (osaphatikizidwa):
a. Chotsani nyali zachifunga za fakitale, (ngati zili ndi zida), kuchokera pazokwera kumbuyo kwa bamper ya fakitale, (Mkuyu 15)
b. Sankhani dalaivala / kumanzere LED Cube Light Bracket, (Mkuyu 16). Gwirizanitsani Bracket kumbuyo kwa Bumper ndi kuphatikiza (5) 6mm x 20mm Combo Bolts ndi (5) 6mm Flange Nuts.
c. Gwirizanitsani Kuwala kwa Cube (Sikuphatikizidwa) kuti mutsegule pamwamba pa Bracket Yokwera.
d. Bwerezani Njira Zam'mbuyomu kuti muyike bulaketi yowala yokwera / kumanja kwa cube ndi kuwala.
e. ZINDIKIRANI: Ngati magetsi sangayikidwe, phatikizani (2) Mesh Fill Panels ku Cube Light Brackets ndi (4) 6mm x 20mm Combo Bolts ndi (4) 6mm Flange Nuts, (Mkuyu 17)

CHOCHITA 16
Dziwani ngati pakati 20” LED kuwala bar, (osaphatikizidwe), kapena Mesh Fill Panel adzaikidwa. Center 20 ”Kuyika kwa bar ya LED (kuwala sikuphatikizidwe).

a. Sankhani (2) "L" Mabulaketi a LED, (Mkuyu 18). Gwirizanitsani Ma Brackets ku (2) ma tabu okwera kumbuyo kwa bampa ndi kuphatikiza (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers ndi (2) 8mm Hex Nuts. . Khalani omasuka panthawiyi.
b. Gwirizanitsani kuwala kwa LED ku "L" Mabulaketi a LED okhala ndi zida zophatikizidwa ndi kuwala kapena zophatikizidwa (2) 8mm x 16mm Hex Bolts, (2) 8mm Lock Washers ndi (2) 8mm x 24mm Flat Washers, (Mkuyu 18) . Musamangitse kwathunthu hardware panthawiyi.
c. Tsatirani malangizo a wopanga kuwala kuti muyike bwino nyali.

Center Mesh Fill Panel Installation (osayika Fill Panel ndi kuwala).

a. Bwerezani Gawo lapitalo kuti muyike (2) "L" Mabakiteti a LED.
b. Gwirizanitsani Center Mesh Fill Panel ku "L" Mabulaketi a LED omwe ali ndi (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers ndi (2) 8mm Hex Nuts, (Mkuyu 19)
c. Kankhani Fill Panel kumbuyo kwa Bumper ndikumangitsa zida zonse.

(Mkuyu 18) Gwirizanitsani "L" Mabulaketi a LED ngati mukuyika kuwala kwapakati pa LED (osaphatikizidwe) kapena Center Mesh Fill Panel.
Gwirizanitsani License Plate Bracket ku BumperCHOCHITA 18
Ngati mbale ya laisensi yakutsogolo ikufunika, phatikizani License Plate Bracket pamabowo a Bumper ndi (2) 6mm x 20mm Button Head Screws, (4) 6mm Flat Washers ndi (2) 6mm Nylon Lock Nuts. Ikani (2) Mapulagi a Plastiki M'mabowo apakati mu Bracket, (Mkuyu 21). Gwiritsirani ntchito zomangira za fakitale kuti mumake laisensi mbale ku Square Plastic Plugs.

CHOCHITA 20
Bwezeretsani grille yapulasitiki, kamera ngati ili ndi zida ndi chivundikiro chochotsedwa mu Gawo 1, (Chithunzi 1).

CHOCHITA 21
Ikani Bumper pansi kutsogolo kwa galimotoyo. Ma Model okhala ndi masensa, amalumikiza Zowonjezera za Wire Harness mu (2) masensa mu Bumper, (Mkuyu 22)

(Mkuyu 22) Ma Model okhala ndi masensa, pulagi Wire Harness Extensions (onani Gawo 14) pamabampu a fakitale mu masensa omwe amaikidwa pa Bumper.

CHENJEZO! Osakwawa pansi pa bumper pokhapokha ngati itakhazikika bwino pa midadada kapena ma stand kapena bampa itagwa.

CHOCHITA 23
Lembani mipata (3) mu mbale yoyikira dalaivala/kumanzere kumbuyo kwa Bumper ndi Bracket ya Frame. Ikani (1) "T" Nut Plate kumbuyo kwa Bracket ya Frame, (Mkuyu 23) Gwirizanitsani Bumper ku Bracket ya Frame ndi "T" Nut Plate yokhala ndi (3) 12mm Hex Bolts, (3) 12mm Lock Washers ndi (3) 12mm Flat Washers, (Mkuyu 24). Bwerezani kuti muphatikize wokwera / kumanja.

(Mkuyu 24) Dalaivala/kumanzere kwa Bumper yolumikizidwa ndi Frame Bracket (Zindikirani kuyika kowunikira kwa cube)

CHOCHITA 25
Sankhani dalaivala/kumanzere Mapiko apansi. Gwirizanitsani Mapiko kumapeto kwa Bumper ndi (1) 8mm x 20mm Hex Bolt, (1) 8mm x 16mm Small Flat Washer ndi (1) 8mm Flange Nut, (Chithunzi 25 ndi 26). Gwirizanitsani pamwamba pa Mapiko pansi pa bumper ya fakitale ndi (2) 6mm Button Head Combo Bolts ndi (2) 6mm Flange Nuts, (Mkuyu 26) Bwerezani izi kuti muphatikize wokwera / Mapiko apansi kumanja ku Bumper.

(Mkuyu 26) Gwirizanitsani “Phiko” loyendetsa kumanzere kwa Bumper mpaka kumapeto kwa Bumper ndi pansi pa bampa ya fakitale. Kuyika kojambulidwa kuchokera kuseri kwa bumper

(Mkuyu 27) Kuyika kwathunthu (20" Double Row Light Bar ndi Magetsi awiri a LED Cube sizikuphatikizidwa)

CHOCHITA 26
Chitani kuyendera nthawi ndi nthawi pakuyika kuti muwonetsetse kuti zida zonse ndi zotetezeka komanso zolimba.

IRONBISON IB-CCS1-03 Front Bumper Installation Guide

Torque & Zida

Mndandanda wa Gawo

CHOCHITA 1
Tsegulani hood ndikuchotsa chivundikiro cha pulasitiki pamwamba pa grill ndi radiator, (Mkuyu 1) Ma Model okhala ndi kamera yokhala ndi grille, chotsani kamera. Kenako, chotsani zomangira zomangira grille ku chithandizo chapakati cha radiator. Zida zonse zikachotsedwa, kokerani grille molunjika kuchokera mgalimoto kuti mutulutse grille pazigawo, (Mkuyu 2) Ikani grille pamalo oyera, ofewa.
(Mkuyu 1) Chotsani chivundikiro ndi zomangira zomangira grille
(Mkuyu 2) Kokani mwamphamvu chowotcha kuchokera mgalimoto

CHOCHITA 2
Chotsani mbale ya layisensi ndi bulaketi. Pamitundu yokhala ndi nyali zachifunga za fakitale ndi/kapena masensa a bamper, masulani chingwe cholowera ku bampa, (Mkuyu 3)
ZINDIKIRANI: Cholumikizira cholumikizira mawaya chili mmwamba ndi kumbuyo kwa wokwera / kumanja kwa bampa. Tulutsani zomata zomangirira liner yonyamula anthu / kumanja kuti mulowetse pulagi ya zingwe. Chotsani zida kutali ndi bumper.
(Mkuyu 3) Kupyolera pa chingwe chotchinga chokwera/kumanja, chotsani zingwe zolowera kutsogolo (muvi)

CHOCHITA 3
Kuchokera kuseri kwa dalaivala / kumanzere kwa bumper, chotsani zida zomangira chothandizira chakunja chakunja kwa bamper, (Mkuyu 4)
(Mkuyu 4) Chotsani zida zomangira cholumikizira chakunja ku bumper (muvi)

CHOCHITA 4
Pezani ndi kuchotsa mabawuti a hex omwe akumangirira pansi pa bumper ku bumper bracket yomwe ili kumapeto kwa chimango, (Mkuyu 5)
(Mkuyu 5) Chotsani mabampu otsika (muvi) 

CHOCHITA 5
Bwerezani masitepe 3 & 4 kuti muchotse cholumikizira cholumikizira cholumikizira chokwera / chothandizira bampu yakumanja ndi bulaketi yotsika.

CHOCHITA 6
Bwererani pamwamba pa bamper. Kokani kumapeto kwa chivundikiro cha mphira pakati pa bampa ndi radiator kuti muwonetse mabawuti omwe amangiriza pamwamba pa bulaketi ku bulaketi ya chimango, (Mkuyu 6)
(Mkuyu 6) Kokani chivundikiro chakumbuyo kuti mupeze mabampu apamwamba

CHOCHITA 7
Ikani midadada kapena ma jeki pansi pa bampu yakutsogolo kuti muyichirikize pakuchotsa bawuti. Chingwecho chikathandizidwa bwino, kuchokera pamwamba, chotsani mabampu omangirira gululo pamwamba pa bulaketi, (Mkuyu 6)

CHENJEZO! Thandizo likufunika kuti chotchingira chikhale pamalo pochotsa bawuti kuti chotchinga chisagwe. Mosamala tsitsani chophatikizira chachikulu chokhala ndi mabulaketi kuchokera kumapeto kwa chimango.

CHENJEZO! Osakwawa pansi pa bumper pokhapokha ngati itakhazikika bwino pa midadada kapena ma stand kapena bampa itagwa.

CHOCHITA 8
Chotsani mbedza zonse ziwiri kumapeto kwa chimango ngati zili ndi zida, (Mkuyu 7)
(Mkuyu 7) Chotsani mbedza zokokera ngati zili ndi zida 

CHOCHITA 9
Sankhani dalaivala / kumanzere Frame Bracket, (Mkuyu 8) Tsegulani Bracket kumapeto kwa chimango. Lowetsani (1) Puleti ya Bolt Yakumanzere Kumapeto kwa chimango ndi kutuluka m'mabowo a m'mbali mwa chimango ndi Bracket Yokwera.

ZINDIKIRANI: Chingwe Chokwera Chilichonse chidzafuna (1) Kumanzere Kumanzere ndi (1) Kumanja kwa Bolt Plate kuti akhazikitse.

CHOCHITA 10
Gwirizanitsani Bracket ku Left Offset Bolt Plate ndi zophatikizira (2) 12mm Zochapira Zophwathira, (2) 12mm Mtedza wa Nayiloni wa 1mm, (10) 1mm Wochapira Wophwatsuka ndi (10) XNUMXmm Nylon Lock Nut, (Mkuyu 8). Bwerezani kuti muyike (1) Kumanja kwa Bolt Plate mumabowo okumbukira mbali ina ya Bracket ya Frame, (Mkuyu 9)

(Mkuyu 8) Gwiritsani ntchito (1) Kumanzere Kumanzere ndi (1) Kumanja Kumapeto kwa Maboti Katatu kuti muphatikize dalaivala/ Bracket yamanzere pa chimango
(Mkuyu 9) Bracket ya Dalaivala / kumanzere kwa Frame yayikidwa

CHOCHITA 11
Bwerezani masitepe 9 & 10 kuti muphatikize wokwera / kumanja kwa Bracket Mounting Bracket.

CHOCHITA 12
Chotsani damu la mpweya. Phatikizani bumper ya fakitale kuti muchotse chodzaza chocheperako, (Mkuyu 10)

ZINDIKIRANI: Damu la mpweya ndi gulu lodzaza madzi sizingakhazikitsidwenso.

CHOCHITA 13
Dziwani ngati bumper ili ndi masensa oimika magalimoto akutsogolo.

Mitundu yopanda masensa:

a. Kankhani zophatikizidwa (2) Mapulagi a Sensor Hole Pulasitiki m'mabowo a masensa, (Mkuyu 11).

Phatikizani gulu lakutsogolo kuti muchotse choyikapo chocheperako (muvi)
Pitani ku Gawo 14. Ma Model okhala ndi masensa oyimitsa magalimoto.
a. Chotsani ndi kuchotsa (2) masensa apakati pa bumper ya fakitale.
b. Sankhani (1) sensor. Chotsani chisindikizo cha silicone kuchokera kumapeto kwa sensa. Tsegulani Foam Seal yayikulu yophatikizidwa kutsogolo kwa sensor, (Mkuyu 12)

Chotsani chisindikizo choyambirira cha silikoni ku sensa. Slide idaphatikizanso Foam Seal kumapeto kwa sensor
c. Lowetsani sensa yokhala ndi Seal mu sensor mount pa hoop pa Bumper, (Mkuyu 13).
d. Ikani Foam Spacer kumapeto kwa sensa. Kanikizani Sensor Cap ndikulowa pa phiri la sensor, (Mkuyu 13)
Kankhani Sensor Cap mu manja okwera

CHOCHITA 14
Sonkhanitsaninso bumper ya fakitale. Pamitundu yokhala ndi masensa, sankhani (1) Wire Harness Extension. Kanikizani Zowonjezera Zowonjezera kudzera pa bowo loyikira sensa pakati pa bampa ya fakitale ndikulumikiza cholumikizira chamkati cha fakitale. Bwerezani kuti muyike Zowonjezera Zomangira zotsalira.

CHOCHITA 15
Dziwani ngati magetsi akufakitale, (ngati ali ndi zida), magetsi a LED Cube, (osaphatikizidwe), kapena ngati palibe magetsi omwe adzayikidwe ndi Bumper.

Mitundu yokhala ndi ndikugwiritsanso ntchito nyali zachifunga za fakitale:

a. Siyani nyali zachifunga zolumikizidwa ndi mwana wa pulasitiki kumbuyo kwa bumper ya fakitale, (Mkuyu 14).

Lumikizaninso bumper popanda choyikapo chocheperako. Kumbuyo kwa dalaivala/kumanzere kwachitsanzo chokhala ndi chithunzi cha chifunga
b. Ikaninso bampu yafakitale. Kuyika kwamtundu wa Cube LED kuwala (osaphatikizidwa):
a. Chotsani nyali zachifunga za fakitale, (ngati zili ndi zida), kuchokera pazokwera kumbuyo kwa bamper ya fakitale, (Mkuyu 15)

Chotsani kuwala kwa chifunga cha fakitale ngati mukuyika magetsi amtundu wa cube wa LED kapena Mesh Fill Panels
b. Sankhani dalaivala/kumanzere LED Cube Light Bracket, (Mkuyu 16).

Ikani dalaivala/kumanzere LED cube kuwala Bracket
Gwirizanitsani Bracket kumbuyo kwa Bumper ndi kuphatikiza (5) 6mm x 20mm Combo Bolts ndi (5) 6mm Flange Nuts.
c. Gwirizanitsani Kuwala kwa Cube (Sikuphatikizidwa) kuti mutsegule pamwamba pa Bracket Yokwera.
d. Bwerezani Njira Zam'mbuyomu kuti muyike bulaketi yowala yokwera / kumanja kwa cube ndi kuwala.
e. ZINDIKIRANI: Ngati magetsi sangayikidwe, phatikizani (2) Mesh Fill Panels ku Cube Light Brackets ndi (4) 6mm x 20mm Combo Bolts ndi (4) 6mm Flange Nuts, (Mkuyu 17)

 Gwirizanitsani Dzazani Panel ku Bracket Yowala ngati palibe kuwala komwe kudzayikidwe
CHOCHITA 16
Dziwani ngati pakati 20” LED kuwala bar, (osaphatikizidwe), kapena Mesh Fill Panel adzaikidwa. Center 20 ”Kuyika kwa bar ya LED (kuwala sikuphatikizidwe).

a. Sankhani (2) "L" Mabulaketi a LED, (Mkuyu 18).

Gwirizanitsani "L" Mabulaketi a LED ngati mukuyika kuwala kwapakati pa LED (osaphatikizidwe) kapena Center Mesh Fill Panel.
Gwirizanitsani Ma Brackets ku (2) ma tabu okwera kumbuyo kwa bampa ndi kuphatikiza (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers ndi (2) 8mm Hex Nuts. . Khalani omasuka panthawiyi.
b. Gwirizanitsani kuwala kwa LED ku "L" Mabulaketi a LED okhala ndi zida zophatikizidwa ndi kuwala kapena zophatikizidwa (2) 8mm x 16mm Hex Bolts, (2) 8mm Lock Washers ndi (2) 8mm x 24mm Flat Washers, (Mkuyu 18). Musamangitse kwathunthu hardware panthawiyi.
c. Tsatirani malangizo a wopanga kuwala kuti muyike bwino nyali.

Center Mesh Fill Panel Installation (osayika Fill Panel ndi kuwala).

a. Bwerezani Gawo lapitalo kuti muyike (2) "L" Mabakiteti a LED.
b. Gwirizanitsani Center Mesh Fill Panel ku "L" Mabulaketi a LED omwe ali ndi (2) 8mm x 25mm Hex Bolts, (4) 8mm x 24mm Flat Washers, (2) 8mm Lock Washers ndi (2) 8mm Hex Nuts, (Mkuyu 19)

Gwirizanitsani Center Mesh Fill Panel ku "L" Mabakiteti a LED (Osayika Fill Panel ndi kuwala kwa LED)
c. Kankhani Fill Panel kumbuyo kwa Bumper ndikumangitsa zida zonse.

CHOCHITA 17
Gwirizanitsani Edge Trim pamwamba pa Bumper, (Mkuyu 20)

Ikani Rubber Trim m'mphepete mwa Bumper

CHOCHITA 18
Ngati mbale ya laisensi yakutsogolo ikufunika, phatikizani License Plate Bracket pamabowo a Bumper ndi (2) 6mm x 20mm Button Head Screws, (4) 6mm Flat Washers ndi (2) 6mm Nylon Lock Nuts. Ikani (2) Mapulagi a Plastiki M'mabowo apakati mu Bracket, (Mkuyu 21). Gwiritsirani ntchito zomangira za fakitale kuti mumake laisensi mbale ku Square Plastic Plugs.

Gwirizanitsani License Plate Bracket ku Bumper

CHOCHITA 20
Bwezeretsani grille yapulasitiki, kamera ngati ili ndi zida ndi chivundikiro chochotsedwa mu Gawo 1, (Chithunzi 1).

CHOCHITA 21
Ikani Bumper pansi kutsogolo kwa galimotoyo. Ma Model okhala ndi masensa, amalumikiza Zowonjezera za Wire Harness mu (2) masensa mu Bumper, (Mkuyu 22)

Ma Model okhala ndi masensa, pulagi Wire Harness Extensions (onani Gawo 14) pamabampu a fakitale mu masensa omwe amaikidwa pa Bumper.

CHENJEZO: Kuti mupewe kuvulala kapena kuwonongeka kwa galimoto, musapitirire mpaka Bumper itathandizidwa mokwanira komanso motetezeka.
CHENJEZO! Osakwawa pansi pa bumper pokhapokha ngati itakhazikika bwino pa midadada kapena ma stand kapena bampa itagwa.

CHOCHITA 23
Lembani mipata (3) mu mbale yoyikira dalaivala/kumanzere kumbuyo kwa Bumper ndi Bracket ya Frame. Ikani (1) "T" Nut Plate kumbuyo kwa Bracket ya Frame, (Mkuyu 23) Gwirizanitsani Bumper ku Bracket ya Frame ndi "T" Nut Plate yokhala ndi (3) 12mm Hex Bolts, (3) 12mm Lock Washers ndi (3) 12mm Flat Washers, (Mkuyu 24).

Dalaivala/kumanzere kwa Bumper yolumikizidwa ndi Frame Bracket (Zindikirani kuyika kowunikira kwa cube)
Bwerezani kuti muphatikize wokwera / kumanja.

CHOCHITA 25
Sankhani dalaivala/kumanzere Mapiko apansi. Gwirizanitsani Mapiko kumapeto kwa Bumper ndi (1) 8mm x 20mm Hex Bolt, (1) 8mm x 16mm Small Flat Washer ndi (1) 8mm Flange Nut, (Chithunzi 25 ndi 26). Gwirizanitsani pamwamba pa Mapiko pansi pa bumper ya fakitale ndi (2) 6mm Button Head Combo Bolts ndi (2) 6mm Flange Nuts, (Mkuyu 26) Bwerezani izi kuti muphatikize wokwera / Mapiko apansi kumanja ku Bumper.
c
(Mkuyu 25) Gwirizanitsani “Phiko” loyendetsa galimoto/kumanzere kwa Bumper kumapeto kwa Bumper ndi pansi pa bampa ya fakitale (mivi)

(Mkuyu 26) Gwirizanitsani “Phiko” loyendetsa kumanzere kwa Bumper mpaka kumapeto kwa Bumper ndi pansi pa bampa ya fakitale. Kuyika kojambulidwa kuchokera kuseri kwa bumper

(Mkuyu 27) Kuyika kwathunthu (20" Double Row Light Bar ndi Magetsi awiri a LED Cube sizikuphatikizidwa)

CHOCHITA 26
Chitani kuyendera nthawi ndi nthawi pakuyika kuti muwonetsetse kuti zida zonse ndi zotetezeka komanso zolimba.

www.ironbisonauto.com Tsamba 10 la 10 Rev. 6/27/23 (JH)

Zolemba / Zothandizira

IRONBISON IB-CCS1-03 Front Bamper [pdf] Kukhazikitsa Guide IB-CCS1-03, IB-CCS1-03 Bampu Yakutsogolo, Bumper Yakutsogolo, Bumper

Maumboni

• Buku Logwiritsa Ntchito