DIY Yakaderera-Mutengo Inoyangarara Valve yeLow Tech Irrigation Automation ine Ollas
Bhuku reMirayiridzo
DIY Yakaderera-Mutengo Inoyangarara Valve yeLow Tech Irrigation Automation ine Ollas
ne lmu34
Kana iwe usingade kuve pamisoro yenyaya yekurasa mvura ( https://www.latimes.com/california/story/2022-08-22/kimkardashian-kevin-hart-california-drought-water-waste)
ingave nguva yakanaka yekuisa kana kuvandudza gadheni rako rekudiridza.
Izvi zvinodzidziswa zvinoratidza nzira yekugadzira yakaderera-inodhura, yakaderera-tech yekufambidzana valve.
- Inoshanda zvakanaka munzvimbo ine simba shoma (kureva mvura inobva mutangi remvura inonaya)
- Yaisazokwanisa kubata kumanikidza (semvura inobva kune network yemvura yemumba). Ona danho rechitanhatu kana uchingokwanisa kuwana mvura yekugovewa kwakadai.
Ini ndaida kuvandudza zvishoma iyo ollas system ine yakaderera-tech otomatiki kuitira kuti ndigadzirise ollas netangi remvura inonaya.
Ndakatanga basa iri neiyi inodzidziswa: yakaderera-tech greenhouse automation, iyi inogadziridza yechikamu chekudiridza.
Kunyangwe ndakawana mibairo yakanaka neiyo yakaderera-tech kudiridza otomatiki setup mugreenhouse yangu, pane akati wandei mapoinzi andaida kuvandudza:
Kubatana kwepasi pevhu kwehari: inoshanda zvakanaka asi inoita kuti zviome kurongazve mapoto kana kuita kugadzirisa, panewo njodzi yekudonha nekufamba kwenguva.
Mapoto ega ega: haana kugadziridzwa senge ollas echokwadi angave (iyo yakakura radius yepoto iri padyo nepasi pevhu asi kune ollas iyi ndiyo diki radius, semhedzisiro, iyo yakanyanya kupararira mvura inoitika pasi pevhu ne ollas. )
Saka ndaida kushandisa ollas echokwadi asina kubatanidzwa pasi pevhu. Mhinduro iri nyore ndeyekuisa vharafu yekunamira mune yega yega, zvinosuruvarisa, ini handina kukwanisa uye chero inotengeswa yekuvharisa vharuvhu yaizopinda muolla (nekuda kweradius yayo diki)….ngatiite imwe ipapo…
Ndakaedza setups akawanda akasiyana… ndakatomboedza mudhudhudhu carburetor oat pin .. asi izvo zvandinotsanangura mune izvi zvisingaverengeki ndizvo zvakashanda… kumwe kuedza kwangu kwese hakuna kupa mhedzisiro yakanaka (pakarepo kana nekufamba kwenguva).
Une zvikamu zviviri mune izvi zvinodzidziswa, kubva panhanho 2 kusvika ku5 nzira yekugadzira vharafu yekuputira uchishandisa 3D printer, uye kubva panhanho 7 kusvika 12 kana iwe usina 3D printer.
Supplies:
- Maolla mashoma ane butiro rawo…handizive kuti zviri nyore sei kuita maollas munyika yako…kana zvisiri nyore ungave mukana wakanaka wekugadzira rako wega bhizinesi…
- mabhora epolystyrene kana mazai (7cm dhayamita)… anoda kuva akakura zvakakwana kusunda vharuvhu, uye madiki zvekuti apinzwe mumaollas.
- 2mm tsvimbo yendarira (ndakawana yangu ichitengeswa sesimbi yendarira)
- mutete-walled silicon chubhu (4 mm kunze dhayamita, 3mm mukati dhayamita)
- hose yemvura yekudiridza yakajairika (inotengeswa muno i4 mm mukati dhayamita, 6mm kunze kwedhayamita) zvibatanidza zvepombi iyi yemvura diki.
- 2 x 3mm screws, nzungu, uye washer
- PLA inochema nokuda kwezvikamu zvakadhindwa zve 3D
Kune iyo isiri-3D yakadhindwa shanduro yakafanana nepamusoro asi PLA inotsiviwa ne:
- Aluminium yakaita L (10x20mm 50mm kureba)
- pachimiro chealuminium (10 mm yakafara, 2 zvidimbu 40 mm kureba, 2 zvidimbu 50 mm kureba)
- square aluminium chubhu (8x8mm 60mm kureba)
- maviri madiki pop rivets (anogona kutsiviwa nema screws kana iwe usina pop rivet pfuti)
Nhanho 1: Ngationei Ichishanda Kutanga…
Vhidhiyo diki iyi inokwidziridzwa ne8 kuratidza vharafu yekuputira mukuita.
Danho 2: Dhinda Zvikamu
Ndakagadzira zvikamu zvangu kuti zvishandiswe ne2mm tsvimbo uye 6mm mvura hose…
Ndakashandisa PLA inodzivirira mvura uye iri nyore kudhinda.
Danho 3: Zvikamu Gungano
Gungano iri nyore, isa tsvimbo yendarira uye ucheke kusvika pakukura kwaunoda (bvumira kukwana kwakaringana pakati pezvikamu, usazvisungirire pamwe chete, michina inofanira kushanda zvakanaka)
Ndakaona zviri nyore kushandisa chibooreso chemagetsi kuisa chimuti chebhurasi mubhora repolystyrene. Sezvo bhora iri richisundidzira mashandiro ese, harifanire kutsvedza zviri nyore parutanda rwendarira. Kana uchinge waungana, unogona kugadzirisa chiyero chemvura chaunoda muollas nekufambisa kumusoro kana pasi pemvura. Ita shuwa kuti tsvimbo yendarira ipfupi pane kudzika kweiyo ollas kana inogona kuchengetedza vharafu munzvimbo yakavharwa.
Iyo chidimbu chidiki chesilicon chubhu inongopinzwa mupombi nhema, kurerutsa kuiswa, uye kunyorovesa kutanga.
Iwe unozoona kuti iyo mechanic inopinza zvinyoro nyoro iyo silicone chubhu kunyangwe iri panzvimbo yakavhurika.a
Nhanho 4: Shandura iyo Ollas Lid
- shandisa ndiro yakadhindwa kumaka maburi mana anodiwa
- drill: maburi maviri achashandiswa kuchengetedza ndiro pachivharo anoboorwa ne4mm drill bit. Mamwe maviri (imwe yekurega tsvimbo yendarira ifambe zvakasununguka uye imwe kurega hose yemvura ichipinda mukati) inoboorwa ne6mm drill bit. Ndakashandisa masonry drill bits (yekongiri) inoita basa rakanaka pavhu.
- chengetedza ndiro ine screws mbiri uye woisazve tsvimbo yendarira nebhora rayo repolystyrene mumeshini.
 |
 |
Nhanho 5: Edza uye Isa Yako Itsva Sisitimu Yekudiridza!
Mufananidzo wacho unoratidza maviri ollas pasi pekuedzwa.
Vachavigwa munzvimbo yavo.
Nhanho 6: Ko Kana Ndisina Mvura Yemvura Yemvura?
Zvakanaka, isa imwe 🙂 https://www.instructables.com/DIY-Rain-Barrel/
Seimwe sarudzo, unogona kungogadzira tangi diki pakati pekugoverwa kwemvura uye maollas aunoda kudyisa otomatiki, "inopwanya" kudzvanywa kwemvura yakagoverwa (sezvakataurwa pakutanga iyi vharafu yekuputira haigone kubata kumanikidza kwemvura kubva kuvanhu. network kana pombi).
Iri tangi redoro raizozadzwa otomatiki nevharuvhu yechiyero "yakasimba" (seyatinayo muzvimbuzi zvedu, yakachipa uye iri nyore kugadzira sezvikamu zvakasara). Iyo tangi haidi kuve yakakura asi yakakwira zvakakwana (yakakwirira kupfuura iyo yepamusoro-soro maollas sezvo isu tichishandisa simba rinokwevera zvinhu pasi kune maollas).
Nhanho yechinomwe: Ini Handina 7D Printer
3D kudhinda zvikamu zvakadaro ndiyo nzira iri nyore kunyanya kana iwe uchida kugadzira mavharuvhu akati wandei, zvisinei, kana iwe usina 3D yakadhindwa kana usina kuwana nyore kune imwe unogona kugadzira vharafu uchishandisa zvikamu zvinowanikwa muzvitoro zveDIY (aluminium proles. )
Ndiri kukurudzira dhizaini yakati siyanei pano, tsvimbo yendarira haidi kuenda nepakati pe ollas lid (inogona kuoneka seadvan.tage, zvisinei, isu hatichaoni zvakare kana ollas isina chinhu kana kwete kubva kunze zvakare, izvo zviri nyore ndinofunga). Iyi dhizaini inogona kuve yakagadziriswa 3D kudhinda.
 |
 |
Nhanho 8: Cheka maAluminium Profiles
- square prole: 60mm kureba
- pabhawa: 2x 40 mm uye 2x 50mm kureba
- L chimiro: 50 mm kureba
Nhanho 9: Dhonza Zvikamu zveAluminium
Ichi ndicho chikamu chakakosha. Hunhu hwemadhiraini huchakanganisa kunaka kweiyo meshini yese (yakanaka parallelism inobvumira kushanda zvakanaka).
Ini ndinofunga zvingave zvakaoma kuwana chimwe chinhu chakanaka zvakakwana pasina chibooreso.
Chinhu chinonyanya kukosha ndechekuita kuti maburi mumaoko ealuminium anyatsoenderana. Kuti uite izvi ndinokurudzira kuti utange kuchera gomba pane rimwe remaoko (rimwe reakarebesa rine maburi matatu) wobva washandisa iri setemplate kuchera maoko matatu asara.
Shandisa chibhakera chepakati kuisa nemazvo mamaki eburi rako usati waboora.
 |
 |
Nhanho 10: Cheka Cork
chimwe chikamu chekupedzisira chisipo, chinobatanidza axis oater kune michina. Ndakashandisa chidimbu chebhodhoro rekoki:
- cheka chidimbu che 5mm chakafara chekork (mukureba kwayo)
- chera maburi maviri akaparadzana 25mm pachiso chimwe
- chera gomba rimwe rakadzika kuti uise oater axis
Nhanho 11: Unganidza Zvikamu neBrass Axis
Tine ve axis yekuisa, ini ndakawedzera mamwe anomira akagadzirwa kubva kune zvimedu zvinopisa glue tsvimbo yakacherwa pakati pavo.
Iyo meshini mufananidzo munhanho yechitanhatu inofanirwa kukwana kuti unzwisise izvo zvinofanirwa kuitwa.
Nhanho 12: Isa pane Ollas Lid
Iyi dhizaini inoda maburi matatu chete: 3 (2mm) kuchengetedza iyo L-yakaita prole ine screws maviri, uye imwe (4mm) yekuisa iyo micro drip yekudiridza hose, inofanirwa kunge iri padyo sezvinobvira kune sikweya bar.
Danho 13: Ndatenda
Ndatenda ku https://www.terra-idria.fr/ akandipa maollas maviri ebvunzo dzangu.
Ndatenda kuna Poterie Jamet wandakachinjana naye ndichigadzira vharafu iyi uye achandipa maollas mashoma kuti ndiratidze chirongwa ichi kuMugadziri Faire Lille (France) 2022.
Waita zvakanaka! uye ndine chokwadi chekuti vanhu vachafarira chokwadi chekuti wawedzera maira kuwedzera shanduro isina kudhindwa! Ndatenda nekugovana 🙂
Zvinyorwa / Zvishandiso
 |
zvinodzidziswa DIY Yakaderera Mutengo Inoyangarara Valve yeLow Tech Irrigation Automation NeOllas [pdf] Bhuku reMirayiridzo DIY Yakaderera Mutengo Inoyangarara Valve yeLow Tech Irrigation Automation ine Ollas |
