MSI CD270 Multi Node Compute Server

Fa'amatalaga

• Fa'ata'ita'iga: G52-S3862X1
• CPU: CD270-S3071-X2
• Drive Bays: 12 x Hot-Swap 2.5 U.2 Drive Bays (PCIe 5.0 x4, NVMe)
• Memory: Supports DDR5 DIMM slots compatible with RDIMMs, 3DS-RDIMM, and MRDIMMs

CD270-S3071-X2
Server System Quick Start Guide

Fa'amatalaga

1	COM USB Type-A Port	5	Faiga Tulaga Uila
2	USB 2.0 Ituaiga-O le Uafu	6	UID LED Button (default)/ System Reset Button*
3	1000Base-T Ethernet Port (for mgmt.)	7	System Power LED Button
4	Mini-DisplayPort	8	OCP 3.0 Mezzanine Card Slot

* The UID LED button can also function as system reset button, configured using jumper J1_1.

System Node Tray Removal

Taua

• Power Off Node First: Removing a powered-on node will cause immediate power loss.
• Independent Power: Each node operates with its own power supply. Turning off one node does not affect others.

Laasaga Aveesea

1. Pull the thumb latch aside to release the node.
2. Grasp the handle to gently slide the node out of its slot.

Support the weight of the node while removing it to prevent accidental drops.

PPU

Single Intel® Xeon® 6900P series processors, TDP up to 500W per node.

CPU ma Heatsink Fa'apipi'i

Manatu
Each node supports 12 DDR5 DIMM slots, compatible with RDIMMs, 3DS-RDIMM and MRDIMMs

Ituaiga DIMM	Max Faafia	Avanoa maualuga ile DIMM
RDIMM/ 3DS-RDIMM	6400 MT/s (1DPC)	256 GB
MRDIMM	8800 MT/s (1DPC)

DDR5 Only DIMM Configuration Diagram ( for Intel® Xeon® 6900P Series)

⚠ Taua

• E tatau ona i ai le itiiti ifo ma le tasi DDR5 DIMM i le socket.
• O faʻasologa o mafaufauga DDR5 e manaʻomia tutusa ituaiga DIMM, tulaga, saoasaoa, ma densities.
• Fa'afefiloi tagata fa'atau, le 3DS/3DS RDIMMs, 9×4 RDIMMs, po'o le x8/x4 DIMMs e le fa'atagaina.
• E le fa'amaonia le fa'afefiloi o DIMM fa'atasi ai ma alaleo fa'agaioia. A 'ese'ese laina, e fa'aletonu le faiga i le saoasaoa masani aupito maualalo.

Komiti Fa'atonu

On Board Connectors, Jumpers and LEDs

Igoa	Fa'amatalaga
Komiti Fa'atonu
JPICPWR_1~4	12V PICPWR power connectors (12-pin)
JPICPWR_5	12V PICPWR power connectors (6-pin)
JPWR1~2	4-pin power connectors
JMCIO1~9	MCIO 8i connectors (PCIe 5.0 x8)
M2_1~2	M.2 avanoa (M Key, PCIe 5.0 x2, 2280/22110)
OCP0	OCP 3.0 mezzanine slot (PCIe 5.0 x16, NCSI supported)
DC-SCM	DC-SCM 2.0 pito pito
JCOOL2	4-Pin liquid leak detection header
JCOOL3	6-Pin liquid cooling header
IUSB3	USB 3.2 Gen 1 so'oga (5 Gbps, mo 2 USB ports)
JFP1~2	DC-MHS fa'aulutala fa'atonu
JPDB_MGNT	PDB management header
JIPMB1	IPMB header (debug only)
JVROC1	VROC connector (debug only)
FBP_I2C_1~3	Ulutala I2C
JCHASSIS1	Ulutala fa'aulu
JPASSWORD_C_1	Fa'amatalaga manino le osooso (fa'amau pine 1-2, masani)
JUART_SEL1	UART BMC/CPLD filifili osooso (fa'amau pine 1-2, UART BMC i le PPU)
JTAG_SEL2	JTAG select jumper (default pin 2-3, BMC to CPU)
JBAT1	MBP/ I3C select jumper (default pin 1-2, MBP)
JBAT2	RTC clear jumper (default pin 1-2, Normal)
JBAT7	PESTI flash select jumper (default pin 2-3, PESTI2 flash)
LED_H1, LED_L1	Port 80 debug LEDs
MGT1 DC-SCM Module
TPM	SPI TPM Header (for TPM20-IRS)
M2_1	M.2 Slot (M Key, for ROT1)
J_JTAG	Manual programming header (debug only)
J3D2	Force BMC update jumper (default pin 1, Normal)
J3C1	FRU jumper (default pin 2-3, FRU normal operated)
J3C5	JTAG SW jumper (default pin 2-3, JTAG SW enable)
J1_1	ID/ Reset button select jumper (default pin 1-2, ID Button)
LED1	BMC tātā fatu LED

Fesili e Fai soo

• Q: Can I mix different types of DIMMs in this system?
  A: No, mixing vendors, non-3DS/3DS RDIMMs, 9×4 RDIMMs, or x8/x4 DIMMs is not allowed. It is recommended to use identical DIMMs for optimal performance.
• Q: What is the maximum memory capacity supported per DDR5 DIMM?
  A: The maximum capacity supported per DDR5 DIMM is 256 GB.

Pepa / Punaoa

MSI CD270 Multi Node Compute Server [pdf] Taiala mo Tagata Fa'aoga X2, S386-S3071-v1.0-QG, G52-S3862X1, CD270 Multi Node Compute Server, CD270, Multi Node Compute Server, Compute Server, Server

Fa'asinomaga

• Tusi Taiala