LowPowerLab ATX-RASPI-R2 Pule Faʻatonu Pisi Pipi

Fa'amatalaga Taua

Ina ia faʻaitiitia le tau, e le faʻapipiʻi le Raspberry Pi i se faʻamau mana, ae e faigofie ona faʻaopoopo lau oe lava! O lenei ta'iala o le a fa'aali atu ai ia te oe le fa'aopoopoina o se fa'amau mana i lau Raspberry Pi e mafai ona fa'aola ma tape lau polokalama BATOCERA.

O lenei pepa e vaevaeina i ni vaega se lua ma faʻatasi ai ma se faʻamatalaga puupuu o le faʻaogaina.

• Suiga Malosiaga Faapisinisi
  • tu'u mai le motusia moni
  • tau e tusa ma le 10-25 USD
  • e masani ona mana'omia se avanoa e fau ai i totonu
• Ki faigofie po'o ki fa'amau
  • seti faigofie tele
  • tau maualalo
  • leai se eletise e mafai

Aisea e taua ai le ki o le Raspberry Pi? 

E le tatau ona e "ave'esea" le uaea eletise mai lau Pi aua e mafai ona oʻo atu ai i le ogaoga o faʻamaumauga (ma i nisi tulaga, faʻaleagaina faaletino lau SD card). E tusa lava pe sili atu le saunia o le BATOCERA file faiga pi'opi'o e fautuaina e tapuni ma le saogalemu lau Pi e ala i le BATOCERAs Quit Menu po'o le sili atu, fa'aaoga le ki po'o le ki.

Manatua: A tatou "tapeina" le Pi, o le a tuʻuina atu i se tulaga taofi, lea e faʻaaogaina ai se vaega itiiti o le mana. E tutusa lea ma le auala e galue uma ai komepiuta faaonaponei. I totonu o lenei taʻiala savali i le faʻagasologa o le faʻaopoopoina o se ki o le mana e taofi uma ma fafagu le Pi mai se tulaga tu.
E le gata i lea, pe a uma ona tapuni lau Pi, e mafai ona e momotu ma le saogalemu le sapalai eletise (pe a e manaʻo ai) e aunoa ma le popole i faʻamatalaga faʻaleagaina.

Suiga Malosiaga Faapisinisi

O nisi nei o masini eletise fa'apisinisi o lo'o lagolagoina nei. O nei mea e ofoina atu ai se paoa moni, o lona uiga ua matua tape le Raspei. E masani lava o nei masini eletise laiti e faʻapipiʻiina i luga o le Raspei e faʻaaoga ai le ulutala 40 Pin. Mo nisi fa'atonuga fa'apipi'i fa'aaoga so'oga ua tu'uina atu.

Igoa Meafaigaluega	faiga. mana. sui	O fea e fa'atau ai ma fesoasoani fa'aopoopo e fa'apipi'i	Faamatalaga Itulau
ATXRaspi	ATX_RASPI_R2_6	http://lowpowerlab.com/atxraspi/#installation
Mausberry Circuits	MAUSEPA	http://mausberry-circuits.myshopify.com/pages/setup
Pimorini OnOffShim	ONOFFSHIM	https://shop.pimoroni.com/products/onoff-shim
msldigital PiBoard r2013	REMOTEPIBOARD_2003	ttp://www.msldigital.com/pages/support-for-remotepi-board-2013
msldigital PiBoard r2015	REMOTEPIBOARD_2005	http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
UUGear Witty Pi	WITTYPI	http://www.msldigital.com/pages/support-for-remotepi-board-plus-2015
Retroflag Cases	RETROFLAG	http://www.retroflag.com	fa'ataga UART ile config.txt mo le laction LED

Pushbutton Faigofie po'o Suiga

E mafai ona fa'aopoopo se ki e ki ai ma tape lelei lau fa'amafanafana BATOCERA! Ae faapefea?

O le fea fa'amau e fa'aoga? 

E mafai ona e fa'aopoopoina le ki fa'amalo e ki/ tape ai le BATOCERA. O le faamau e mafai ona avea ma se faamau oomi (fa'amau mo sina taimi) po'o se ki ki (ki fa'amau). Fa'aaliga i luga o fa'amau fa'amau: o nisi GPIO o lo'o i ai ni fa'atosina e toso i totonu (tetee e feso'ota'i i le + 3.3V), o lea e sili ai le fa'aogaina o ki e masani ona tatala (fa'apu'upu'u NO) ma nei pine.

e faʻafesoʻotaʻi le ki i le Raspberry Pi GPIO, faʻapipiʻi se PIN i le GPIO3 (PIN faaletino 5 i luga i le agavale) ma le isi i luga o le masini o loʻo i le itu taumatau i le itu taumatau (PIN faaletino 6):

Fa'agaoioi o le ki

Tusi Lesona

o lea o lau ki e iloa e le BATOCERA, e te manaʻomia le faʻaogaina o lenei vaega i ona tulaga.
O lea fa'asa'o batocera.config

• Mo se ki fa'amau fa'asa'o batocera.conf fa'atasi ma lau fa'atonu tusitusiga ma fa'aopoopo system.power.switch=PIN56ONOFF
• Mo sina taimi fa'amau fa'asa'o batocera. conf ma lau fa'atonu OS e mana'omia ma fa'aopoopo system.power.switch=PIN56PUSH
• Toe fai le faiga
• Afai o lo'o e saini ile SSH pe o iai sau fa'amau e tatala ona ulufale lea

batocera-settings --command set --key system.power.switch --value
PIN56ONOFF
batocera-settings --command set --key system.power.switch --value
PIN56PUSH

ua mafai nei ona ki / tape lau masini BATOCERA i se faamau!

Faʻamau menu 

Maua se fa'amalama fa'amalama e ala i le tu'ua o le Emulation Station ma se Keyboard pe maua se avanoa ile terminal ile SSH. Lenei ulufale rpi_gpioswitch ma o le ae vaʻai i se faʻamalama faʻamalama pei o le ata i lalo. Mai iina e mafai ona e filifili ma fa'agaoioia lou mana po'o le sui masini. O le tusitusiga o le a faʻaali atu ia te oe se masini ua uma ona faʻagaoioia (ONOFFSHIM i lenei tulaga) ma o le a faʻaalia mulimuli ane ia te oe se pusa savali laʻititi, pe a fai o le faʻatulagaina o le tau na faʻatulaga lelei. A maeʻa lenei toe faʻafouina le masini ma e tatau ona lelei mea uma.

Lagolago Tagata Fa'atau

rom:
https://wiki.batocera.org/ – Batocera.linux – Wiki
Soʻotaga tumau:
https://wiki.batocera.org/add_powerdevices_rpi_only?rev=1581110157
Fa'afouga mulimuli: 2020/02/07 22:15

https://wiki.batocera.org/
Lolomi i le 2025/06/28 02:48

Pepa / Punaoa

LowPowerLab ATX-RASPI-R2 Pule Faʻatonu Pisi Pipi [pdf] Faatonuga ATX_RASPI_R2_6, MAUSBERRY, OnOffShim, ATX-RASPI-R2 Pule Faʻatonu Pi, ATX-RASPI-R2, Pule Faʻatonu Pi, Pule Pule Pi, Pule Mana.

Fa'asinomaga

• Tusi Taiala