SKYDANCE R Series Ultrathin Touch Slide RF Remote Controller
Features
- Apply to single color, dual color ,RGB, RGB+W or RGB+CCT LED controller.
- Ultra sensitive color adjustment touch slide.
- Each remote can match one or more receiver.
- CR2032 battery powered.
- Operate with LED indicator light.
- Magnet on the back which can be easily stuck on back holder or any metal surfaces.
- White & Black available
Technical Parameters
|
Input and Output |
|
|
Output signal |
RF(2.4GHz) |
| Working voltage |
3VDC(CR2032) |
|
Working current |
<5mA |
| Standby current |
<10μA |
|
Standby time |
1 year |
| Remote distance |
30m(Barrier-free space) |
|
Safety and EMC |
|
|
EMC standard (EMC) |
ETSI EN 301 489-1 V2.2.3 ETSI EN 301 489-17 V3.2.4 |
| Safety standard(LVD) |
EN 62368-1:2020+A11:2020 |
|
Radio Equipment(RED) |
ETSI EN 300 328 V2.2.2 |
| Certifcation |
CE,EMC,LVD,RED |
|
Package |
|
| Size | L156 x W48 x H22mm |
| Gross weight |
0.075kg |
|
Environment |
|
| Operation temperature |
Ta: -30 OC ~ +55 OC |
|
Warranty |
|
| Warranty |
5 years |
Mechanical Structures and Installations
To fix the remote, three options are offered for selection:
Option 1: stuck the remote on any metal surfaces directly.
Option 2: fix the remote’ back holder on the wall with two screws.
Option 3: adhere the remote’ back holder to the wall with paster.
Match Remote Control (two match ways)
End user can choose the suitable match/delete ways. Two options are offered for selection:
Use the controller’s Match key
Match:
Short press match key, immediately press on/off key on the remote.
The LED indicator fast flash a few times means match is successful.
Delete:
Press and hold match key for 5s to delete all match,
The LED indicator fast flash a few times means all matched remotes were deleted.
Use Power Restart
Match:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 3 times on the remote.
The light blinks 3 times means match is successful.
Delete:
Switch off the power, then switch on power, repeat again.
Immediately short press on/off key 5 times on the remote.
The light blinks 5 times means all matched remotes were deleted.
Key function
- R11 1 zone dimming remote
- R12 1 zone CCT remote
- R13 1 zone RGB remote
- R10 1 zone RGB+CCT
- R14 1 zone RGBW remote
Safety information
- Read all instructions carefully before you begin this installation.
- When installing battery, pay attention to the battery positive and negative polarity.
A long time without the remote control, remove the battery.
When remote distance becomes smaller and insensitive, replace the battery. - If no response from the receiver, please re-match the remote.
- Gently handle remote, beware of falling.
- For indoor and dry location use only
Documents / Resources
 |
SKYDANCE R Series Ultrathin Touch Slide RF Remote Controller [pdf] Instruction Manual Ultrathin Touch Slide RF Remote Controller, Ultrathin Remote Controller, Touch Slide RF Remote Controller, Remote Controller, R11, R12, R13, R14, R10 |
 |
SKYDANCE R Series Ultrathin Touch Slide RF Remote Controller [pdf] Owner's Manual R11, R12, R13, R14, R10, R Series Ultrathin Touch Slide RF Remote Controller, R Series, Ultrathin Touch Slide RF Remote Controller, Touch Slide RF Remote Controller, Slide RF Remote Controller, RF Remote Controller, Remote Controller, Controller |
