Shark IP1000 Series PowerDetect Cordless Vacuum Owner's Manual

The PowerDetect Cordless Vacuum is a powerful and versatile cleaning tool designed to make your cleaning tasks easier and more efficient. With features like Flexology, LED battery indicators, and DirtDetect sensors, this vacuum offers a thorough cleaning experience.

Usage Instructions

Charging the Lithium-Ion Battery

Connect the charging unit to a power source.

Insert the vacuum’s battery into the charging unit.
Monitor the LED indicators on the charging unit to track the battery’s charging status.

Removing the Battery
To remove the battery, press the release button located on the vacuum body and slide the battery out.

Selecting Cleaning Modes
You can choose between different cleaning modes like Eco and Boost by pressing the corresponding buttons on the vacuum.

Cleaning and Maintenance
Regularly check and clean the filters, brush rolls, and nozzles to maintain optimal performance.

FAQ

What should I do if the vacuum stops working?
If the vacuum stops working, check for blockages in the nozzles or brush rolls. Clear any obstructions and try again.
How often should I clean the filters?
Clean the filters at least once a month to ensure efficient suction power.

Can I wash the filters?
Yes, you can wash the filters with water. Make sure they are completely dry before reinserting them into the vacuum.

PowerDetect Cordless Vacuum
IP1000 Series

OWNER’S GUIDE

THANK YOU
for purchasing the Shark Power Detect Cordless Vacuum

TIP: You can find the model and serial numbers on the QR code label located on the back of your unit.
TIP: You can locate the date code on one of the prongs of the power cord plug.

REGISTER YOUR PURCHASE

TO BENEFIT FROM YOUR PRODUCT’S EXTENDED GUARANTEE, SIMPLY REGISTER YOUR PURCHASE AT:

shark clean.eu
Scan QR code using mobile device

Please note, products purchased directly from Shark are automatically registered.

Benefits of registering your product and creating an account:

Get easier, faster product support and access to guarantee information

Access troubleshooting and product care instructions
Be among the first to know about exclusive product promotions

RECORD THIS INFORMATION
Model Number:

Serial Number:
Date Code:
Date of Purchase (Keep Receipt):
Store of Purchase:

TECHNICAL SPECIFICATIONS

Voltage: 21.6V
Body Motor Watts: 380W
Nozzle Watts: 120W

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE
This instruction manual is designed to help you get a complete understanding of your new Shark Power Detect Cordless Vacuum?
If you have any questions, please contact customer service at sharkclean.eu

This marking indicates that this product should not be disposed with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material sources. To return your used device, please use the return and collection systems or contact the retailer where this product was purchased. They can take this product for environmentally safe recycling.

IMPORTANT SAFETY INSTRUCTIONS

FOR HOUSEHOLD USE ONLY • PLEASE READ ALL INSTRUCTIONS
BEFORE USING THIS VACUUM.
To reduce the risk of shock and unintended operation, turn off power and remove the ION Power Pack battery before servicing.

NOTE: If you have delicate or wool carpets, particularly loop pile, please try the vacuum on a hidden area first to ensure the spinning brush rolls do not damage or unpick carpet fibres.

WARNING
REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, INJURY, OR PROPERTY DAMAGE:

This vacuum consists of a motorised nozzle, wand, and handheld vacuum. These components contain electrical connections, electrical wiring, and moving parts that potentially present risk to the user.
Before each use, carefully inspect all parts for any damage. If a part is damaged, discontinue use.
Use only identical replacement parts.

This vacuum contains no serviceable parts.
Use only as described in this manual.
DO NOT use the vacuum for any purpose other than those described in this manual.
With the exception of the filters and dust cup, DO NOT expose any parts of the vacuum to water or other liquids.

NOT allow the appliance to be used by children. Keep the appliance and its cord out of reach of children. Do not allow to be used as a toy. Close supervision is necessary when used near children.
GENERAL USE
This appliance can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Cleaning and user maintenance should not be done by children.
Always turn off the vacuum before connecting or disconnecting any current carrying hoses, motorised nozzles, chargers, batteries, or other electrical or mechanical parts.

DO NOT handle plug or vacuum with wet hands.
DO NOT use without dust cup, filters, and brush-roll in place.
Only use Shark branded filters and accessories. Damage caused by non-Shark filters and accessories may not be covered by the guarantee.

DO NOT put any objects into nozzle or accessory openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
DO NOT use if nozzle or accessory airflow is restricted. If the air paths or the motorised floor nozzle become blocked, turn the vacuum off. Remove all obstructions before you turn on the unit again.
Keep nozzle and all vacuum openings away from hair, face, fingers, uncovered feet, or loose clothing.

DO NOT use if vacuum is not working as it should, or has been dropped, damaged, left outdoors, or dropped into water.
Use extra care when cleaning on stairs.
- DO NOT leave the vacuum unattended while powered on.

When powered on, keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibres.
If you have delicate or wool carpets, particularly loop pile, please try the vacuum on a hidden area first to ensure the spinning brush-rolls do not damage or unpick carpet fibres.
DO NOT use to pick up:
- Liquids
- Large objects
- Hard or sharp objects (glass, nails, screws, or coins)
- Large quantities of dust (including drywall, fireplace ash, or embers). DO NOT use as an attachment to power tools for dust collection.
- Smoking or burning objects (hot coals, cigarette butts, or matches)
- Flammable or combustible materials (lighter fluid, petrol, or kerosene)
- Toxic materials (chlorine bleach, ammonia, or drain cleaner)
DO NOT use in the following areas:
- Wet or damp surfaces
- Outdoor areas
Spaces that are enclosed and may contain explosive or toxic fumes or vapours (lighter fluid, petrol, kerosene, paint, paint thinners, mothproofing substances, or flammable dust)
Turn off the vacuum before plugging in or unplugging the charger.

Turn off the vacuum before any adjustment, cleaning, maintenance or troubleshooting.
During cleaning or routine maintenance, DO NOT cut anything other than hair, fibres, or string wrapped around the brush-roll.
Allow all filters to air-dry completely before replacing in the vacuum to prevent liquid from being drawn into electric parts.

DO NOT modify or attempt to repair the vacuum or the battery yourself, except as indicated in this manual.
DO NOT use the battery or vacuum
if it has been modified or damaged. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or risk of injury.
Turn off all controls before unplugging.
Always turn off this appliance before connecting or disconnecting motorised nozzle or hand tool.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
BATTERY PACK
The battery is the power source for the vacuum. Carefully read and follow all charging instructions.
To prevent unintentional starting, ensure the vacuum is powered off before picking up or carrying the vacuum? DO NOT carry the appliance with your finger on the power switch.

For IP1000 use only with DK30A-263100H-V or YLJX2I-E263100 charger.
Keep the battery away from all metal objects such as paper clips, coins, keys, nails, or screws. Shorting the battery terminals increases the risk of fire or burns.
Under abusive conditions, liquid may be ejected from the battery. Avoid contact with this liquid, as it may cause irritation or burns. If contact occurs, flush with water. If liquid contacts eyes, seek medical help.

Battery should not be stored at temperatures below 3°C (37.4°F) or above 40°C (104°F) to maintain long-term battery life.
DO NOT charge battery at temperatures below 5°C (40°F) or above 40°C (104°F). Charging improperly or at temperatures outside of the specified range may damage the battery and increase the risk of fire.
Store the appliance indoors.

DO NOT expose the battery to fire or temperatures above 130°C (265°F) as it may explode.
Use appliances only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
Disconnect the battery pack from the appliance before making any adjustments, changing accessories, or storing appliance. Such preventive safety measures reduce the risk of starting the appliance accidentally.

Always ensure that the rechargeable battery is removed from the appliance before inserting into the battery charging sleeve.
For IP1000 Series, use only Shark battery pack XBATR640EU (21.6V 3750mAh 81wh).

ASSEMBLY (IP1000 SERIES)

Slide the Wand onto the neck of the Floor Nozzle until it clicks into place.

Align the Hand Vacuum nozzle opening with the top of the wand and slide it on until it clicks into place.
For proper operation, ensure all components are completely connected and clicked into place.

CHARGING YOUR LI-ION BATTERY

Prior to first use, charge the battery completely. A full charge takes approximately 6 hours.

RUNTIMES PER FULLY CHARGED BATTERY
With a full charge, the unit will have up to a 70-minute runtime. Visit sharkclean.eu online for more information.

LED BATTERY POWER AND CHARGING INDICATORS NOTE: Battery consumption will vary depending on the mode being used:

ECO – Maximum Runtime, saves battery power

AUTO – Optimises suction and power for maximum cleaning
BOOST – Maximises suction. Uses the most batter power

Charging

LED on the battery pack will pulse yellow when reaching 0-75% charge.
LED on the battery pack will pulse green from 75% – 100% charge.
White LED the battery pack is fully charged.

NOTE: Full charge takes approximately 6 hours.

Additional Notes

LEDs turn off once the battery is fully charged.
Unit will not power on when charger is connected.

In Use

RECYCLING THE LI-ION BATTERY
When the Shark Li-ion battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is illegal to place spent lithium-ion batteries in the standard rubbish bin. Return spent batteries to an authorised recycling centre or to the retailer for recycling. Contact your local recycling centre for information on where to drop off the spent battery.

NOTE: The Shark battery, like all lithium-ion batteries, will naturally decrease in capacity over time from the 100% capacity of a new battery.

CHARGING YOUR LI-ION BATTERY

To remove the battery from the vacuum, press the release button on the battery and slide out of the handle compartment. To reinstall, slide the Battery back into the compartment until it clicks into place.

To charge the battery, remove it from the vacuum and insert into the charging sleeve. Once the battery is showing as fully charged reinsert into the handle compartment on the vacuum (see charging indicators on previous page)

NOTE: The main unit comes with a partial charge. For maximum runtime, charge fully before first use (approximately 6 hours). Leaving the unit plugged in will not damage battery life.

USING YOUR VACUUM

CONTROLS AND CLEANING MODES

Press the button on the UI Screen to turn on power To turn off power, press the button again.
To toggle between ECO, DETECT, and BOOST modes, press the mode selection trigger on the handle (shown above).
In DETECT mode, Detect Technology automatically adjusts vacuum and nozzle power to maximise cleaning performance and optimise runtime.
To begin cleaning with the floor nozzle, disengage the lock by stepping on the nozzle and tilting the hand vac down.

NOTE: For – Best Cleaning on ASTM and IEC Cleaning Tests, Use Boost Mode.

DETECT TECHNOLOGY EXPLAINED

NOTE: Detect Technology is ONLY operational in Detect Mode and is activated automatically when the unit is in use.

Vacuum identifies dirtier areas and automatically boosts suction power to pull in hidden dirt.
- White LED No heavy debris detected, low suction
- Pink LED Debris is being cleaned, medium suction
- Purple LED Heavy debris detected, high suction
Vacuum floor nozzle detects edges and corners and maximises suction and power to remove stubborn dirt.

Brushroll and vacuum responds to surface changes and automatically adjusts to optimise your clean.
Senses low-light situations and automatically illuminates dark areas to help you spot debris.

FLEXOLOGYFlexology allows you to flex the wand to reach under furniture and clean debris in hard-to-reach areas.

STORAGE

To put the vacuum into storage mode, press the Flexology wand unlock button while folding the handheld vacuum forward until it is resting against the wand.
To release vacuum from storage mode, unfold the vacuum until the wand straightens and clicks securely back in place.

ABOVE-FLOOR CLEANING

Detach the hand vacuum to clean above-floor areas. Press the front latch release button on the hand vac where it meets the wand, then lift off the hand vacuum. To attach an accessory to the hand vacuum, slide it into the opening in the nozzle. To remove, press the front latch release button on the hand vac where it meets the wand, and slide out the accessory.
To detach the floor nozzle from the wand, step on the nozzle while pressing the nozzle release button at the bottom of the wand. Lift the wand to remove it. To reattach the wand, align it over the neck of the floor nozzle, then slide it on until it clicks into place.

MAINTAINING YOUR VACUUM

EMPTYING THE HANDHELD VACUUM DUST CUP (IP1000 SERIES)

To empty the handheld vacuum dust cup, turn off the power and hold the vacuum directly over the rubbish bin. Press the release button and the dust cup lid will drop open, releasing debris.

CLEANING THE VACUUM DUST CUP

To access the dust cup on your IP1000 or IP3000 hand vacuum, engage the dust cup removal button and pull downward disengage from the hand vacuum (Fig. 1).

CLEANING THE VACUUM ANTI-ALLERGEN FILTER

NOTE: For best results, clean your filters at least once a month and replace the filters regularly. To clean filters, clear loose debris and rinse with cold water ONLY to prevent damage from cleaning chemicals. Allow all filters to dry fully before reinstalling to prevent liquid from being drawn into electrical parts.

To access filter, press the dust cup release button and remove the dust cup.
Pull the release tab to remove the filter for the vacuum.
After cleaning, slide the filter back into the vacuum.

NOZZLE MAINTENANCE

Turn off the vacuum.
Press the nozzle release button to detach the nozzle from the wand.
Press the soft roller release button and slide the soft roller out of the nozzle.
Clear any blockages and remove any debris from the soft roller and floor nozzle.
Tap off loose debris and wipe the soft roller clean with a dry towel. Hand wash the soft rollerif needed, using only water, and then let it air dry completely before reinstalling.
When the soft roller is completely dry, reinstall it into the nozzle by inserting it into the nozzle until it clicks.

Turn off the vacuum.
Press the nozzle release button to detach the nozzle from the wand.
Remove rear squeegee by turning screws.
Clear our any blockages and debris from behind the squeegee.
Reinstall squeegee and turn screws until they lock into place.

CLEANING THE SENSORS
Make sure to clean the Detect sensors regularly, as hair and other debris may build up and obstruct them. If the sensors are partially obstructed, Clean Sense Detect mode will not function as expected.

To clean the sensors:

Turn off power and remove the floor nozzle.
Locate the Dirt Detect Sensor (Fig. 1), the Light Detect Sensor on (Fig. 2), the Edge Detect sensor (Fig. 3) and the Floor Detect Sensor (Fig. 4).
Gently wipe the sensors with a microfibre cloth and remove all hair and debris.
Reattach the floor nozzle to the rest of the unit and turn on power. Verify that the unit is functioning normally.

CHECKING FOR BLOCKAGES IN THE VACUUM
If you run over a hard or sharp object or notice a noise change while vacuuming, check for blockages or objects caught in the brushroll.

Checking for Blockages in the Hand Vacuum:

Turn off the vacuum.
Remove the hand vacuum from the wand.
Check all intake openings to the dust cup and remove any debris or blockages.

Checking for Blockages in the Wand:

Turn off the vacuum.
Detach the hand vacuum and floor nozzle from the wand.
Check both ends of the wand for blockages and debris.
Clear away any debris or blockages.

Checking for Blockages in the Floor Nozzle:

Turn off the vacuum.
Detach the wand from the floor nozzle.
Press the soft roller release button and slide the brushroll out of the nozzle.
Clear any blockages and release any debris from the brushroll and floor nozzle.
Slide the soft roller back into the nozzle, ensuring everything is lined up and in place.

TROUBLESHOOTING

WARNING: To reduce the risk of shock and unintended operation, turn off power and remove the battery before servicing.

Vacuum is not picking up debris. No suction or light suction. Third indicator light on hand vacuum is solid yellow. (Refer to Checking for Blockages section for more information.)

Dust cup may be full; empty dust cup.
Check floor nozzle for blockages; clear blockages if required.
Remove any string, carpet fibers, or hair that may be wrapped around the brushroll.
Check connection between hand vacuum and wand for blockages; clear blockages if required.
Check filters to see if they need cleaning. Follow instructions for rinsing and completely air-drying the filters before reinstalling them.

Vacuum lifts area rugs.

Make sure you are not engaging Boost mode. Take care when vacuuming area rugs or rugs with delicately sewn edges.
Turn off the unit to disengage from the carpet, then restart.

The brushroll in the floor nozzle doesn’t spin.

Immediately turn off the vacuum. Remove any blockages before turning the vacuum back on.Make sure
the hand vacuum is tilted back far enough for the brushroll to engage while in use.
If the floor nozzle has headlights and they are not illuminated, there is a connection issue between the hand vacuum, wand, and nozzle. Try detaching the parts, then reconnecting them.

Vacuum turns off on its own.
There are several possible reasons for the vacuum turning off on its own, including blockages, battery issues, and overheating. If vacuum turns off on its own, perform the following steps:

Turn on the vacuum and check the battery indicator lights on the hand vacuum. If recharging is needed, make sure vacuum power is off placing it on the charging dock.
Empty dust cup and clean filters (See the Cleaning the Dust Cup and Filter section).
Check wand, accessories, and inlet openings and remove any blockages.
Allow unit and battery to cool for at least 45 minutes, until they return to room temperature.
Press the On/Off switch to restart the vacuum.

NOTE: If vacuum still does not operate properly, contact Customer Service

ADDITIONAL ACCESSORIES AVAILABLE

A Crevice Tool
B Duster Crevice Tool
C Flexible Crevice Tool
D Anti-Allergen Brush
E Multi-Surface Tool
F Motorised Hand Tool
G Wide Upholstery Tool
H Car Detail Kit
I Replacement Battery
J Hand Vacuum Pre-Motor Filter
K Hand Vacuum Post-Motor Anti-Allergen Filter L Battery Charging Sleeve

NOTE: Not all accessories come with all units. Please see the Quick Start Guide on the packaging box for your unit’s configuration. To order additional accessories, visit sharkclean.eu.

SharkNinja Europe Limited, 3150 Century Way, Thorpe Park,
Leeds
LS15 8ZB, UK

Documents / Resources

	Shark IP1000 Series PowerDetect Cordless Vacuum [pdf] Owner's Manual IP1000 Series, IP1000 Series PowerDetect Cordless Vacuum, PowerDetect Cordless Vacuum, Cordless Vacuum, Vacuum
	Shark IP1000 Series PowerDetect Cordless Vacuum [pdf] User Guide IP1000 Series PowerDetect Cordless Vacuum, IP1000 Series, PowerDetect Cordless Vacuum, Cordless Vacuum, Vacuum

References

User Manual

Shark IP1000 Series PowerDetect Cordless Vacuum

Product Information