ٽريڪ ايبل 5002CC ليب ٽائمر

نشانيون
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

ڊسپلي کي صاف ڪرڻ صفر

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

ٽائمر آپريشن

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

ڳڻپ جو وقت مقرر ڪرڻ

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

نوٽ: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two exampگهٽ ڏنل آهن.

Exampلي 1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. 2 بٽڻ کي دٻايو.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Exampلي 2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. 3 بٽڻ کي دٻايو.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

وضاحتون

• ڏيکاريو: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• قرارداد: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

تڪڙو حوالو

• الف- چينل ڏيکاريل آهي
• ب- چينل ون (1) بٽڻ
• سي- چينل ٻه (2) بٽڻ
• ڊي- چينل ٽي (3) بٽڻ
• اي- چينل وقت يا ڏيکاريل نه آهي.
• ايف- چينل ٽائيمنگ آهي پر ڏيکاريل ناهي.
• جي- ڪلاڪ (ايڇ) بٽڻ
• H- Minutes (M) button
• I – Seconds (S) button

چينل اشارو
LCD indicators report the status of each channel.

بيٽري مٽائڻ

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

بيٽريون داخل ڪرڻ کان پوءِ، پڪ ڪريو ته ٽائمر ڊسپلي عام طور تي ڪم ڪري رهيو آهي. ٽائمنگ آپريشن دوران چمڪندڙ حصا ڊسپلي تي ظاهر ٿي سگهن ٿا. جيڪڏهن اهو ٿئي ٿو ته صرف بيٽرين کي هٽائي ۽ ٻيهر داخل ڪندي ري سيٽ ڪريو. بيٽرين جو هر سيٽ عام حالتن ۾ 1 کان 2 سالن تائين رهڻ گهرجي. جڏهن بيٽرين کي تبديل ڪرڻ جي ضرورت هجي ته LCD ڊسپلي خالي رهندو.

وارنٽي

وارنٽي، خدمت، يا بحالي
وارنٽي، خدمت، يا ٻيهر حاصل ڪرڻ لاء، رابطو ڪريو:

قابل اعتماد مصنوعات 12554 پراڻي گليسٽن آر ڊي. سوٽ B230 Webاسٽير ، ٽيڪساس 77598 آمريڪا

• فون .281 482-1714
• فيڪس 281 482-9448
• اي ميل support@traceable.com
• www.traceable.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

لي. نمبر 5002
Traceable® Cole-Parmer جو رجسٽرڊ ٽريڊ مارڪ آھي.

©2020 Traceable® پروڊڪٽس. 92-5002-00 Rev. 6 070825

FAQs

دستاويز / وسيلا

ٽريڪ ايبل 5002CC ليب ٽائمر [pdf] استعمال ڪندڙ ھدايت 5002CC ليب ٽائمر، 5002CC، ليب ٽائمر، ٽائمر

حوالو

• استعمال ڪندڙ دستي