Revèy laboratwa 5002CC ki ka trase

ALARM
Each channel has a distinct electronic tone that sounds at the end of its timing period. Channel One has one repeating beep; Channel Two has two repeating beeps; and Channel Three has three repeating beeps. A channel’s tone will sound for 1 minute then shut off automatically to preserve battery life.

EKLARASYE DISPLAY A ZEWO

Press and hold (approximately 2 seconds) the 1, 2, or 3 button to clear the display to zero for Channel One, Two, or Three respectively. If no channel is active, pressing and holding the 1, 2, or 3 button will shut off the unit entirely.

OPERASYON TIMER

All three timing channels work essentially the same way, so once you understand how Channel One operates, Channels Two and Three will seem extra easy.

FIJERE YON TAN KONTAJ

1. Press the 1 button, digital display will then show all zeros. The symbol will be below the 1 button indicating Channel One is displayed.
2. Set the hours to be timed: Press the H button until the desired number of hours are displayed. For rapid advancement, press and hold button.
3. Set the minutes to be timed: Press the M button until the desired number of minutes are displayed. For rapid advancement, press and hold button.
4. Set the seconds to be timed: Press the S button until the desired number of seconds are displayed. For rapid advancement, press and hold button.
5. When the desired amount of time is showing on the digital display, simply press the 1 button to begin timing. You’ll know timing has begun when the seconds start counting down.
6. A single repeating electronic tone will sound at the end of the timing period and the symbol below the 1 button indicates status of the timing operation. (See “Channel Indicators” table).
7. To reset a channel to zero, to turn off a channel, or to turn off a channel while it is timing, simply press and hold down the appropriate channel (Channel One, Two or Three) for two seconds.

REMAK: The tone will continue to sound for 1 minute or until it is turned off. To turn off the tone, simply press the 1 button and release.

EXAMPLES
Channels Two and Three operate the same way as Channel One, except you press the 2 button for Channel Two or the 3 button for Channel Three in every instance you pressed the 1 button when timing in Channel One. Two exampyo bay les.

Example 1
Time 1 hour, 20 minutes, and 30 seconds in Channel 2:

1. Peze bouton 2.
2. Press H button once to read “1”.
3. Press M button until display reads “20” minutes.
4. Press S button until display reads “30” seconds.
5. Press 2 button to start timing.
6. When the tone (two repeating beeps) sounds, press 2 button to turn it off.

Example 2
Time 9 hours, 15 minutes, and 10 seconds in Channel 3:

1. Peze bouton 3.
2. Press H button until display reads “9” hours.
3. Press M button until display reads “15” minutes.
4. Press S button until display reads “10” seconds.
5. Press 3 button to start timing.
6. When the tone (three repeating beeps) sounds, press 3 button to turn it off.

SPECIFICATIONS

• Ekspozisyon: ¼* high, 5-digit  LCD
• Timing capacity: 9 hrs, 59 mins, 59 sec
• Rezolisyon: 1 sec Accuracy: 0.001%
• Size, weight: 3 x 3 x 1⅜”, 4 oz

REFERANS RAPID

• A- Chanèl la parèt
• B- Bouton Chanèl En (1)
• C- Bouton Chanèl De (2)
• D- Bouton Chanèl Twa (3)
• Chanèl E a pa ap tan oswa li pa ap parèt
• Chanèl F la ap tanmen men li pa parèt.
• Bouton G- Èdtan (H)
• H- Minutes (M) button
• I – Seconds (S) button

Endikatè Chèn
LCD indicators report the status of each channel.

RANplasman batri

To replace the batteries, remove the back housing of the timer by giving the large screw on the back of the unit a half turn with a coin or screwdriver, then replace batteries as shown using two “AA” alkaline batteries. (Do not use regular or heavy-duty batteries. They do not have sufficient power to drive the unit.)

Apre ou fin mete pil yo, asire w ke ekran revèy la ap fonksyone nòmalman. Pandan operasyon revèy la, segman ki ap flache ka parèt sou ekran an. Si sa rive, tou senpleman re-inisyalize lè w retire epi mete pil yo ankò. Chak seri pil ta dwe dire 1 a 2 zan nan kondisyon nòmal. Ekran LCD a ap rete vid lè w bezwen ranplase pil yo.

GARANTI

GARANTI, SÈVIS, OSWA RECALIBRASYON
Pou garanti, sèvis, oswa rekalibrasyon, kontakte:

PWODWI TRAZE 12554 Old Galveston Rd. Suite B230 WebSter, Texas 77598 USA

• Ph. 281 482-1714
• Faks 281 482-9448
• Imèl support@traceable.com
• www.traceable.com

Traceable® Products are ISO 9001:2015 Quality- Certified by DNV and ISO/EC 17025:2017 accredited as a Calibration Laboratory by A2LA.

Chat. Nimewo 5002
Traceable® se yon mak komèsyal ki anrejistre Cole-Parmer.

©2020 Pwodwi Traceable®. 92-5002-00 Rev 6 070825

FAQ

Dokiman / Resous

Revèy laboratwa 5002CC ki ka trase [pdfGid Itilizatè 5002CC Minutè Laboratwa, 5002CC, Minutè Laboratwa, Minutè

Referans

• Manyèl itilizatè