Can the GuliKit ES Pro controller be used with a controller program or software?
The GuliKit ES Pro is designed to be a plug-and-play controller that handles its customization directly on the hardware rather than through a dedicated…
Manuals+ Q&A
Controller questions & answers
Browse answered questions about Controller, including setup, troubleshooting, compatibility and maintenance.
Browse topics
Answered questions
Newest questionsWhat is the SMD component part number for the 5V USB output regulator on the DOKIO SC2430D?
The DOKIO SC2430D user manual provides general technical specifications but does not include a detailed circuit diagram or a Bill of Materials (BOM) for…
Why is the Enter button not working to access settings and make changes?
To access the settings and make changes on the PowMr HHJ60-PRO, you must follow a specific sequence of button presses as the ENTER button…
I cannot heat up higher than 21 °C.
According to the manual for the SAMSUNG MWR-SH11N Wired Remote Controller, the heat mode allows you to adjust the desired temperature by 1 °C…
Why is my Hisense air conditioner not working?
If your Hisense air conditioner is not responding or working, please check the following troubleshooting steps based on the L1-04 remote controller manual: Check…
What is the maximum allowed value for two solar panels in series with a 48V battery system?
Based on the Y&H SY Controller manual, for a 48V Battery system, the specifications are as follows: Solar Voltage Range (VOC): The recommended range…
I am using a GLEDOPTO GL-C-618WL with software version GL-C-618W and WS2812B-LED-Stripes. The stripes on outputs IO16 and IO12 work fine. However, when I connect additional WS2812B-stripes to IO2 and IO4 and configure them in the software, these outputs remain non-functional. Can you please tell me how to correctly operate or configure the LED-stripes on IO2 and IO4?
The GLEDOPTO GL-C-618WL controller supports connecting up to four digital LED strips. The output terminals are labeled V+, GND, IO16, IO12, IO4, IO2, IO13,…
Why does the LB button on my EasySMX M20 controller stay red and register as being constantly pressed even when I am not holding it?
Based on the EasySMX M20 manual, the behavior you are describing (the indicator turning red and the button registering as continuously pressed) is characteristic…
What is the View button on the GameSir G8 Plus Galileo controller?
On the GameSir G8 Plus Bluetooth Mobile Controller, the button typically referred to as the "View" button (common in Xbox layouts) is represented by…
How do I turn off the GameSir G8 Plus and fix Bluetooth pairing issues where the controller keeps blinking and is not discoverable?
Based on the GameSir G8 Plus manual, here are the steps to resolve power and Bluetooth connectivity issues: Powering Off: To manually turn off…
What are the different operation modes for the TOSOT YAP1F7 remote controller, and can they cause dry air?
The TOSOT YAP1F7 remote controller features five primary operation modes. You can cycle through these by pressing the MODE button: Auto Mode (Triangle icon):…
How do I customize the splash screen on the RadioMaster TX16S MK3 when replacing the image on the SD card does not work?
To customize the splash screen on your RadioMaster TX16S MK3 (running EdgeTX), simply replacing the file on the SD card may not be enough…
Is it possible to set a minimum constant fan speed (e.g., level 2 or 3) that increases to a higher speed (e.g., level 10) when humidity rises?
Based on the Mars Hydro M01 Intelligent Fan Controller manual, the device does not support a "minimum constant speed" while in AUTO Mode. In…
Why is my Rain Bird ESP-TM2 controller running the same watering cycle 4 times in a row?
The reason your system is running 4 times in a row is likely because you have set four different Watering Start Times for the…
How can I order a replacement remote for the Changtu Electronic CT-577?
Manuals+ provides digital copies of user manuals and does not sell replacement parts directly. To order a replacement remote for the Changtu Electronic CT-577,…
How do I connect the GAMWIING Aobing Maxplus AB02 to an iPhone?
To connect your GAMWIING Aobing Maxplus (AB02) to your iPhone, follow these steps for iOS Mode: Enter Pairing Mode: Hold down the H +…
How do I adjust or turn off the rumble/vibration settings on the GameSir Nova controller?
To adjust the vibration intensity on the GameSir Nova controller, use the following button combination: Hold the M button + D-pad Up/Down: This increases…
How do I turn the rumble/vibration setting on and off on the GameSir Nova controller?
According to the GameSir Nova HD Rumble Wireless Controller manual, the vibration intensity is adjusted using the M button in combination with the D-pad.…
How do I turn the rumble/vibration setting on and off on the GameSir Nova controller?
According to the GameSir Nova HD Rumble Wireless Controller manual, the vibration intensity is adjusted using the M button in combination with the D-pad.…
How to configure the mA current output on the NIVELCO UNICONT PMG 500?
To configure the current output (mA) on the NIVELCO UNICONT PMG 500, follow these steps: Select Output Type: Enter parameter group 3 (PAR3). Navigate…
Why is there no output voltage even though the PM6 controller is powered on, displaying temperatures, and the POWER ADJ volume is turned?
Based on your description, the PM6 controller is powered and receiving sensor data, but the output signal is not reaching or triggering your SCR…
How can I fix connection issues with the Lenovo Legion Go controllers after resetting and turning off FPS mode?
If your Lenovo Legion Go controllers are failing to connect after a reset and toggling the FPS mode switch, please try the following steps…
How do I customize the splash screen on the RadioMaster TX16S MK3?
To customize the splash screen on your RadioMaster TX16S MK3 (which runs EdgeTX), you need to replace the image file on your SD card.…
Is the DJI Osmo Action GPS Bluetooth Remote Controller compatible with the Osmo Action 5 Pro, and when will the Osmo 360 2 be released?
Based on the official documentation for the DJI Osmo Action GPS Bluetooth Remote Controller, here is the information regarding your request: Compatibility: The manual…