PPI logoScanLog (Pen Drive)
4 / 8 / 16 Channel Recorder + Pen-Drive Interface
Operation Manual

ScanLog 16 Channel Recorder and Pen-Drive Interface

This brief manual is primarily meant for quick reference to wiring connections and parameter searching. For more details on operation and application; please log on to www.ppiindia.net

OPERATOR PARAMETERS

Parameters Settings
Stop Copy No Yes
Select Option 1. None
2. Copy (New)
3. Re-copy (Old)
4. Read Chan Names
5. Recover
(Default : None)
Batch Start No Yes
Balance Slot Time Read Only
Batch Stop No Yes

ALARM SETTINGS

Parameters Settings (Default Value)
Select Channel Pen Drive Version For 4C : Channel-1 to Channel-4
For 8C : Channel-1 to
Channel-8
For 16C : Channel-1 to
Channel-16
Select Alarm AL1, AL2, AL3, AL4
(The actual available options depends on the numbers of Alarms set per channel on
Alarm configuration page)
AL1 Type None Process Low Process High (Default : None)
AL1 Setpoint Min. to Max. of selected input type range
(Default : 0)
AL1 Hysteresis 1 to 30000
(Default : 20)
AL1 Inhibit No Yes
(Default : No)

DEVICE CONFIGURATION

Parameters Settings (Default Value)
Delete Records No Yes

(Default : No)

CHANNEL CONFIGURATION

Parameters Settings (Default Value)
All Chan Common No Yes
(Default : No)
Select Channel Pen Drive Version For 4C : Channel-1 to Channel-4
For 8C : Channel-1 to
Channel-8
For 16C : Channel-1 to
Channel-16
Parameters Settings (Default Value)
Input Type Refer Table 1
(Default : 0 to 10 V)
Resolution Refer Table 1
Signal Low
Input Type  Settings  Default
0 to 20mA 0.00 to Signal High 0
4 to 20mA 4.00 to Signal High 4
0 to 80mV 0.00 to Signal High 0
0 to 1.25V 0.000 to Signal High 0
0 to 5V 0.000 to Signal High 0
0 to 10V 0.00 to Signal High 0
1 to 5V 1.000 to Signal High 1
Signal High
Input Type  Settings  Default
0 to 20mA Signal Low to 20.00 20
4 to 20mA Signal Low to 20.00 20
0 to 80mV Signal Low to 80.00 80
0 to 1.25V Signal Low to 1.250 1.25
0 to 5V Signal Low to 5.000 5
0 to 10V Signal Low to 10.00 10
1 to 5V Signal Low to 5.000 5
Range Low -30000 to +30000
(Default : 0)
Range High -30000 to +30000
(Default : 1000)
Low Clipping Disable Enable
(Default : Disable)
Low Clip Val -30000 to High Clip Val (Default : 0)
High Clipping Disable Enable
(Default : Disable)
High Clip Val Low Clip Val to 30000 (Default : 1000)
Zero Offset -30000 to +30000
(Default : 0)

ALARM CONFIGURATION

Parameters Settings (Default Value)
Alarms/chan 1 to 4
(Default : 4)

RECORDER CONFIGURATION

Parameters Settings (Default Value)
Normal Interval 0:00:00 (H:MM:SS) to
2:30:00 (H:MM:SS)
(Default : 0:00:30)
Zoom Interval 0:00:00 (H:MM:SS) to
2:30:00 (H:MM:SS)
(Default : 0:00:10)
Alrm Toggl Rec Disable Enable
(Default : Enable)
Recording Mode Continuous Batch
(Default : Continuous)
Batch Time 0:01 (HH:MM) to
250:00 (HHH:MM)
(Default : 1:00)
Batch Start Batch Stop No Yes

RTC SETTING

Parameters Settings
Time (HH:MM) 0.0 to 23:59
Date 1 to 31
Month 1 to 12
Year 2000 to 2099
Unique ID Number Read Only

UTILITIES

Parameters Settings (Default Value)
Lock Unlock No Yes
(Default : No)
Factory Default No Yes
(Default : No)
TABLE 1
Option Range (Min. to Max.) Resolution & Unit
Type J (Fe-K) 0.0 to +960.0°C 1 °C or 0.1 °C
Type K (Cr-Al) -200.0 to +1376.0°C
Type T (Cu-Con) -200.0 to +387.0°C
Type R (Rh-13%) 0.0 to +1771.0°C
Type S (Rh-10%) 0.0 to +1768.0°C
Type B 0.0 to +1826.0°C
Type N 0.0 to +1314.0°C
Reserved for customer specific Thermocouple type not listed above. The type shall be specified in accordance with the ordered (optional on request) Thermocouple type.
RTD Pt100 -199.9 to +600.0°C 1°C or 0.1 °C
0 to 20 mA -30000 to 30000 units 1
0.1
0.01
0.001
units
4 to 20 mA
0 to 80 mV
Reserved
0 to 1.25 V -30000 to 30000 units
0 to 5 V
0 to 10 V
1 to 5 V

FRONT PANEL KEYS

FRONT PANEL KEYS
Symbol Key Function
PPI ScanLog 16 Channel Recorder and Pen Drive Interface - icon Scroll Press to scroll through various Process Information Screens in Normal Operation Mode.

PPI ScanLog 16 Channel Recorder and Pen Drive Interface - icon1

Alarm Acknowledge Press to acknowledge / mute alarm output (if active) & to view Alarm Status screen.
PPI ScanLog 16 Channel Recorder and Pen Drive Interface - icon2 DOWN Press to decrease the parameter value. Pressing once decreases the value by one count; keeping pressed speeds up the change.
PPI ScanLog 16 Channel Recorder and Pen Drive Interface - icon3 UP Press to increase the parameter value. Pressing once increases the value by one count; keeping pressed speeds up the change.
PPI ScanLog 16 Channel Recorder and Pen Drive Interface - icon4 SET-UP  

Press to enter or exit set-up mode.

PPI ScanLog 16 Channel Recorder and Pen Drive Interface - icon5 ENTER In Run Mode, press to toggle between Auto & Manual Scan Mode. (Only for 16 Channel version)
In Set-up Mode, press to store the set parameter value and to scroll to the next parameter.

SCROLLING THROUGH VARIOUS SCREENS

The screen shown below are for 4 Channel Version. The sequence is the same for 8 & 16 Channel Version.

PPI ScanLog 16 Channel Recorder and Pen Drive Interface - Channel Version

VIEWING ALARM STATUS SCREEN

PPI ScanLog 16 Channel Recorder and Pen Drive Interface - STATUS SCREEN

16 Channel With Alarm Relay Outputs

PPI ScanLog 16 Channel Recorder and Pen Drive Interface - Relay Outputs

ELECTRICAL CONNECTIONS

PPI ScanLog 16 Channel Recorder and Pen Drive Interface - Relay Outputs1

PPI logo101, Diamond Industrial Estate, Navghar,
Vasai Road (E), Dist. Palghar – 401 210.
Sales : 8208199048 / 8208141446
Support : 07498799226 / 08767395333
E: sales@ppiindia.net,
support@ppiindia.net

Documents / Resources

PPI ScanLog 16 Channel Recorder and Pen-Drive Interface [pdf] Instruction Manual
ScanLog, ScanLog 16 Channel Recorder and Pen-Drive Interface, 16 Channel Recorder and Pen-Drive Interface, Recorder and Pen Drive Interface, Pen Drive Interface

References

Leave a comment

Your email address will not be published. Required fields are marked *