Factory Automation Products India | Automation Solutions in India
Instruction Manual for PPI models including: ScanLog, ScanLog 16 Channel Recorder and Pen-Drive Interface, 16 Channel Recorder and Pen-Drive Interface, Recorder and Pen Drive Interface, Pen Drive Interface
8 Channel With Alarm Relay Outputs - - - - Supply 2425 Analog Inputs CH-1 DEV 1 2 RS485 Comm B Alarm Outputs 9 10 11 121314 151617 1819 20 NO C NCNO C NCNO C NCNO C NC 85~265 VAC
Scan Log Multi-Channel Data-logger | Multi-Channel Scanner | Multi Channel Process Scanner
File Info : application/pdf, 2 Pages, 468.40KB
DocumentDocumentJan 2022 ScanLog (Pen Drive) 4 / 8 / 16 Channel Recorder + Pen-Drive Interface Operation Manual This brief manual is primarily meant for quick reference to wiring connections and parameter searching. For more details on operation and application; please log on to www.ppiindia.net 101, Diamond Industrial Estate, Navghar, Vasai Road (E), Dist. Palghar - 401 210. Sales : 8208199048 / 8208141446 Support : 07498799226 / 08767395333 E: sales@ppiindia.net, support@ppiindia.net OPERATOR PARAMETERS Parameters Stop Copy Select Option Settings No Yes 1. None 2. Copy (New) 3. Re-copy (Old) 4. Read Chan Names 5. Recover (Default : None) Batch Start No Yes Balance Slot Time Batch Stop Read Only No Yes ALARM SETTINGS Parameters Settings (Default Value) Select Channel Pen Drive Version For 4C : Channel-1 to Channel-4 For 8C : Channel-1 to Channel-8 For 16C : Channel-1 to Channel-16 Select Alarm AL1, AL2, AL3, AL4 (The actual available options depends on the numbers of Alarms set per channel on Alarm configuration page) AL1 Type None Process Low Process High (Default : None) AL1 Setpoint Min. to Max. of selected input type range (Default : 0) AL1 Hysteresis 1 to 30000 (Default : 20) AL1 Inhibit No Yes (Default : No) DEVICE CONFIGURATION Parameters Settings (Default Value) Delete Records No Yes (Default : No) CHANNEL CONFIGURATION Parameters Settings (Default Value) All Chan Common No Yes (Default : No) Select Channel Pen Drive Version For 4C : Channel-1 to Channel-4 For 8C : Channel-1 to Channel-8 For 16C : Channel-1 to Channel-16 Parameters Input Type Resolution Signal Low Settings (Default Value) Refer Table 1 (Default : 0 to 10 V) Refer Table 1 Input Type Settings Default 0 to 20mA 0.00 to Signal High 0.00 4 to 20mA 4.00 to Signal High 4.00 0 to 80mV 0.00 to Signal High 0.00 0 to 1.25V 0.000 to Signal High 0.000 0 to 5V 0.000 to Signal High 0.000 0 to 10V 0.00 to Signal High 0.00 1 to 5V 1.000 to Signal High 1.000 Signal High Range Low Range High Low Clipping Low Clip Val High Clipping High Clip Val Zero Offset Input Type Settings Default 0 to 20mA Signal Low to 20.00 20.00 4 to 20mA Signal Low to 20.00 20.00 0 to 80mV Signal Low to 80.00 80.00 0 to 1.25V Signal Low to 1.250 1.250 0 to 5V Signal Low to 5.000 5.000 0 to 10V Signal Low to 10.00 10.00 1 to 5V Signal Low to 5.000 5.000 -30000 to +30000 (Default : 0) -30000 to +30000 (Default : 1000) Disable Enable (Default : Disable) -30000 to High Clip Val (Default : 0) Disable Enable (Default : Disable) Low Clip Val to 30000 (Default : 1000) -30000 to +30000 (Default : 0) ALARM CONFIGURATION Parameters Settings (Default Value) Alarms/chan 1 to 4 (Default : 4) RECORDER CONFIGURATION Parameters Settings (Default Value) Normal Interval 0:00:00 (H:MM:SS) to 2:30:00 (H:MM:SS) (Default : 0:00:30) Zoom Interval Alrm Toggl Rec Recording Mode 0:00:00 (H:MM:SS) to 2:30:00 (H:MM:SS) (Default : 0:00:10) Disable Enable (Default : Enable) Continuous Batch (Default : Continuous) Batch Time 0:01 (HH:MM) to 250:00 (HHH:MM) (Default : 1:00) Batch Start No Batch Stop Yes RTC SETTING Parameters Settings Time (HH:MM) Date Month 0.0 to 23:59 1 to 31 1 to 12 Year Unique ID Number 2000 to 2099 Read Only Parameters Lock Unlock UTILITIES Settings (Default Value) No Yes (Default : No) Factory Default No Yes (Default : No) TABLE 1 Option Type J (Fe-K) Range (Min. to Max.) 0.0 to +960.0°C Type K (Cr-Al) Type T (Cu-Con) Type R (Rh-13%) Type S (Rh-10%) Type B Type N -200.0 to +1376.0°C -200.0 to +387.0°C 0.0 to +1771.0°C 0.0 to +1768.0°C 0.0 to +1826.0°C 0.0 to +1314.0°C Reserved for customer specific Thermocouple type not listed above. The type shall be specified in accordance with the ordered (optional on request) Thermocouple type. RTD Pt100 0 to 20 mA 4 to 20 mA 0 to 80 mV Reserved 0 to 1.25 V 0 to 5 V 0 to 10 V 1 to 5 V -199.9 to +600.0°C -30000 to 30000 units -30000 to 30000 units Resolution & Unit 1 °C or 0.1 °C 1°C or 0.1 °C 1 0.1 0.01 0.001 units Symbol Key Scroll FRONT PANEL KEYS Function Press to scroll through various Process Information Screens in Normal Operation Mode. Alarm Press to acknowledge / mute alarm output (if active) & to Acknowledge view Alarm Status screen. DOWN Press to decrease the parameter value. Pressing once decreases the value by one count; keeping pressed speeds up the change. Press to increase the parameter value. Pressing once UP increases the value by one count; keeping pressed speeds up the change. SET-UP Press to enter or exit set-up mode. ENTER In Run Mode, press to toggle between Auto & Manual Scan Mode. (Only for 16 Channel version) In Set-up Mode, press to store the set parameter value and to scroll to the next parameter. SCROLLING THROUGH VARIOUS SCREENS The screen shown below are for 4 Channel Version. The sequence is the same for 8 & 16 Channel Version. 22/09/16 CH1 OPEN CH3 27.2 10:40:06 CH2 67.4 CH4 27.2 Main Screen Record No = 22/09/16 Channel 1 AL 950.8 Y Channel 3 AL 43.3 Y 264 10:40:06 Channel 2 AL 43.8 Y Channel 4 AL 43.3 Y Record View Screen (Use UP / DOWN Keys to scroll through all stored records) ** ** Channel Names CH1 Temperature CH2 Pressure CH3 Flow Rate CH4 Motor RPM Channel Names Screen 22/09/16 CH1 OPEN CH3 27.2 10:40:06 CH2 67.4 CH4 27.2 Main Screen ** ** Recording Info New Records 50 Old Records 162 File REC30006 Back Up B006_XXX Recording Information Screen VIEWING ALARM STATUS SCREEN 22/09/16 CH1 OPEN CH3 27.2 10:40:06 CH2 67.4 CH4 27.2 Main Screen ALARM STATUS AL1 AL2 AL3 AL4 CH1 CH2 CH3 CH4 ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... ..... Alarm Status Screen 22/09/16 CH1 OPEN CH3 27.2 10:40:06 CH2 67.4 CH4 27.2 Main Screen 16 Channel With Alarm Relay Outputs Analog Inputs CH-1 CH-2 CH-3 CH-4 CH-5 CH-6 CH-7 CH-8 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 CH-9 CH-10 CH-11 CH-12 CH-13 CH-14 CH-15 CH-16 DC Excitation EX 24V 5V 1 2 Analog Input RS485 Comm DC Excitation Alarm Outputs DEV +B B- PC +B B- EX1 +- EX2 Relay 1 Relay 2 Relay 3 Relay 4 - + NO C NC NO C NC NO C NC NO C NC 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CH - X RTD TC V / mV mA Supply 85~265 VAC LN 21 22 23 Analog Inputs Analog Inputs Analog Inputs Analog Inputs ELECTRICAL CONNECTIONS 4 Channel Without Alarm Relay Outputs 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 CH-1 CH-2 CH-3 CH-4 RS485 Comm DEV +B B- 12 PC +B B- 34 DC Excitation EX1 EX2 +-+- 5678 DC Excitation EX1 24V 5V EX2 24V 5V CH - X RTD TC V / mV mA 4 Channel With Alarm Relay Outputs Supply 85~265 VAC LN 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 CH-1 CH-2 CH-3 CH-4 RS485 Comm DEV PC +B B- +B B- 1234 EX 24V 5V 1 2 DC Excitation Alarm Outputs EX1 +- EX2 Relay 1 Relay 2 Relay 3 Relay 4 - + NO C NC NO C NC NO C NC NO C NC 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CH - X RTD TC V / mV mA Supply 85~265 VAC LN 21 22 23 8 Channel Without Alarm Relay Outputs 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 CH-1 CH-2 CH-3 CH-4 CH-5 CH-6 CH-7 CH-8 RS485 Comm DEV B + B- 12 PC B + B- 34 DC Excitation EX1 EX2 +-+- 5678 DC Excitation EX1 24V 5V EX2 24V 5V CH - X RTD TC V / mV mA Supply 85~265 VAC LN 21 22 23 8 Channel With Alarm Relay Outputs 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 CH-1 CH-2 CH-3 CH-4 CH-5 RS485 Comm DEV PC +B B- +B B- 1234 EX 24V 5V 1 2 DC Excitation Alarm Outputs EX1 +- EX2 Relay 1 Relay 2 Relay 3 Relay 4 - + NO C NC NO C NC NO C NC NO C NC 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CH-6 CH - X CH-7 RTD TC CH-8 85~265 VAC LN 21 22 23 Supply V / mV mA