iSMACONTROLLI SFAR-1M-2DI1AO 2 Zolowetsa Pakompyuta ndi Module 1 ya Analogi Yotulutsa Modbus IO

KULAMBIRA
Magetsi	Voltage	10-38 V DC; 10-28 V AC
	Kugwiritsa ntchito mphamvu	2 W @ 24 V DC; 4 VA @ 24 V AC
Zotsatira za analogi	1x volitagKutulutsa	0 V÷10 V (zosintha 1,5 mV)
	1x Zotuluka pano	0 mA÷20 mA (kusankha 5 uA)
		4 mA÷20 mA (kusankha 16 uA)
Zolowetsa pa digito	2x, zomveka "0": 0-3 V, zomveka "1": 6-38 V
Zowerengera	2x, Resolution 32-bits Frequency max 1 kHz
Kuthamangitsa	2400 mpaka 115200 bps
Chitetezo cha ingress	IP40 - kukhazikitsa m'nyumba
Kutentha	Kugwira ntchito -10 ° C - +50 ° C; Kusungirako - 40°C - +85°C
Chinyezi chachibale	5 mpaka 95% RH (popanda condensation)
Zolumikizira	Kutalika kwa 2.5 mm2
Dimension	90 mm x 56,4 mm x 17,5 mm
Kukwera	Kuyika njanji ya DIN (DIN EN 50022)
Zida zapanyumba	Pulasitiki, PC/ABS yozimitsa yokha

GULU LAPANSI

KULUMIKIZANA KWA ZOPHUNZITSA

VoltagKutulutsa

Zotuluka pano

KULUMIKIZANA KWA ZOlowetsa

Zolowetsa pa digito

CHENJEZO

• Zindikirani, mawaya olakwika a mankhwalawa amatha kuwononga ndikubweretsa zoopsa zina. Onetsetsani kuti chinthucho chalumikizidwa bwino ndi mawaya musanayatse magetsi.
• Musanayike mawaya, kapena kuchotsa/kuyika chinthucho, onetsetsani kuti mwazimitsa magetsi. Kulephera kutero kungayambitse kugwedezeka kwamagetsi.
• Osakhudza mbali zokhala ndi magetsi monga ma terminals. Kuchita zimenezi kungayambitse kugwedezeka kwamagetsi.
• Osagawanitsa mankhwalawo. Kuchita zimenezi kungayambitse kugunda kwa magetsi kapena ntchito yolakwika.
• Gwiritsani ntchito zinthu zomwe zili mkati mwa magawo omwe akulimbikitsidwa malinga ndi momwe zimakhalira (kutentha, chinyezi, voltage, kugwedezeka, kukwera kolowera, mlengalenga etc.). Kulephera kutero kungayambitse moto kapena ntchito yolakwika.
• Mangitsani mawaya ku terminal. Kumangika kosakwanira kwa mawaya kutheminali kungayambitse moto.

ZOTSATIRA ZA CHIPANGA

Kulembetsa mwayi

Modbus	Dec	Hex	Register Dzina	Kufikira	Kufotokozera
30001	0	0x00 pa	Mtundu/mtundu	Werengani	Mtundu ndi Mtundu wa chipangizocho
30002	1	0x01 pa	Adilesi	Werengani	Adilesi ya module
40003	2	0x02 pa	Mtengo wamtengo	Werengani & Lembani	Mtengo wa baud RS485
40004	3	0x03 pa	Imani Bits & Data Bits	Werengani & Lembani	Palibe ya Stop bits & Data Bits
40005	4	0x04 pa	Parity	Werengani & Lembani	Parity pang'ono
40006	5	0x05 pa	Kuchedwa Kuyankha	Werengani & Lembani	Kuchedwa kuyankha mu ms
40007	6	0x06 pa	Modbus Mode	Werengani & Lembani	Modbus Mode (ASCII kapena RTU)
40009	8	0x08 pa	Woyang'anira	Werengani & Lembani	Woyang'anira
40013	12	Zamgululi	Default Output State	Werengani & Lembani	Default zotuluka (pambuyo mphamvu kapena watchdog kukonzanso)
40033	32	0x20 pa	Mapaketi olandirira LSR (Osafunikira Reg.)	Werengani & Lembani	Palibe mapaketi omwe adalandira
40034	33	0x21 pa	Mapaketi olandila a MSR (Ofunika Kwambiri Reg.)	Werengani & Lembani
40035	34	0x22 pa	Mapaketi olakwika a LSR	Werengani & Lembani	Palibe mapaketi omwe adalandiridwa ndi zolakwika
40036	35	0x23 pa	Mapaketi olakwika a MSR	Werengani & Lembani
40037	36	0x24 pa	Anatumiza mapaketi LSR	Werengani & Lembani	Palibe mapepala otumizidwa
40038	37	0x25 pa	Anatumiza mapaketi MSR	Werengani & Lembani
30051	50	0x32 pa	Zolowetsa	Werengani	Zolowetsa
40052	51	0x33 pa	Zotsatira	Werengani & Lembani	Zotulutsa
40053	52	0x34 pa	Mtengo wa 1 LSR	Werengani & Lembani	32-bit counter 1
40054	53	0x35 pa	Mtengo wa MSR1	Werengani & Lembani
40055	54	0x36 pa	Mtengo wa 2 LSR	Werengani & Lembani	32-bit counter 2
40056	55	0x37 pa	Mtengo wa MSR2	Werengani & Lembani
40061	60	Zamgululi	Mtengo wapatali wa magawo 1 LSR	Werengani & Lembani	Mtengo wa 32-bit wa kauntala yojambulidwa 1
40062	61	0x3d pa	Mtengo wa MSR1	Werengani & Lembani
40063	62	0x3 ndi	Mtengo wapatali wa magawo 2 LSR	Werengani & Lembani	Mtengo wa 32-bit wa kauntala yojambulidwa 2
40064	63	0x3f ku	Mtengo wa MSR2	Werengani & Lembani
40069	68	0x44 pa	Counter Config 1	Werengani & Lembani	Counter Configuration +1 - muyeso wa nthawi (ngati 0 kuwerengera zikhumbo) +2 - kauntala yogwira modzidzimutsa pamphindi imodzi iliyonse +4 - mtengo wogwira mukalowa wotsika +8 - yambitsaninso kauntala mukatha kugwira +16 - yambitsaninso kauntala ngati kuyika kwachepa +32 - encoder
40070	69	0x45 pa	Counter Config 2	Werengani & Lembani
40073	72	0x48 pa	Gwirani	Werengani & Lembani	Kauntala
40074	73	0x49 pa	Mkhalidwe	Werengani & Lembani	Kauntala yojambulidwa

LANGIZO ZOYAMBIRA

Chonde werengani malangizowo musanagwiritse ntchito kapena kugwiritsa ntchito chipangizocho. Ngati muli ndi mafunso mutawerenga chikalatachi, chonde lemberani Gulu Lothandizira la iSMA CONTROLLI (support@ismacontrolli.com).

• Musanayike mawaya kapena kuchotsa/kuyika chinthucho, onetsetsani kuti mwathimitsa magetsi. Kulephera kutero kungayambitse kugunda kwamagetsi.
• Mawaya olakwika a mankhwalawa amatha kuwononga ndikuyambitsa zoopsa zina. Onetsetsani kuti chinthucho chalumikizidwa bwino ndi mawaya musanayatse magetsi.
• Osakhudza mbali zokhala ndi magetsi monga ma terminals. Kuchita zimenezi kungayambitse kugunda kwa magetsi.
• Osagawanitsa mankhwalawo. Kuchita zimenezi kungayambitse kugunda kwa magetsi kapena ntchito yolakwika.
• Gwiritsani ntchito mankhwalawo mkati mwa magawo omwe akulimbikitsidwa malinga ndi momwe amafotokozera (kutentha, chinyezi, voltage, kugwedezeka, komwe kumakwera, mlengalenga, etc.). Kulephera kutero kungayambitse moto kapena ntchito yolakwika.
• Mangitsani mawaya ku terminal. Kulephera kutero kungayambitse moto.
• Pewani kuyika chinthucho pafupi ndi zida zamagetsi zamphamvu kwambiri ndi zingwe, katundu wolowera, ndi zida zosinthira. Kuyandikira kwa zinthu zoterezi kungayambitse kusokoneza kosalamulirika, zomwe zimapangitsa kuti mankhwalawa asagwiritsidwe ntchito.
• Kukonzekera koyenera kwa mphamvu ndi ma signal cabling kumakhudza ntchito ya dongosolo lonse lolamulira. Pewani kuyala mphamvu ndi mawaya azizindikiro mu thireyi za chingwe zofananira. Zingayambitse zosokoneza mu kuyang'anitsitsa ndi kulamulira zizindikiro.
• Ndikofunikira kuti owongolera mphamvu / ma module omwe ali ndi othandizira magetsi a AC/DC. Amapereka kutchinjiriza kwabwino komanso kokhazikika kwa zida poyerekeza ndi makina osinthira a AC/AC, omwe amatumiza chisokonezo ndi zochitika zosakhalitsa monga ma surges ndi kuphulika kwa zida. Amalekanitsanso zinthu kuchokera kuzinthu zochititsa chidwi kuchokera ku zosintha zina ndi katundu.
• Makina opangira magetsi azinthu ayenera kutetezedwa ndi zida zakunja zochepetsa kuchulukirachulukiratage ndi zotsatira za kutulutsa mphezi.
• Pewani kupatsa mphamvu mankhwalawo ndi zida zake zoyendetsedwa / zoyang'aniridwa, makamaka mphamvu zazikulu komanso zonyamula katundu, kuchokera ku gwero limodzi lamphamvu. Zida zopangira mphamvu kuchokera ku gwero limodzi lamagetsi zimayambitsa chiopsezo choyambitsa zosokoneza kuchokera ku katundu kupita ku zida zowongolera.
• Ngati thiransifoma ya AC/AC ikugwiritsidwa ntchito popereka zida zowongolera, tikulimbikitsidwa kugwiritsa ntchito thiransifoma yopitilira 100 VA Class 2 kuti mupewe zotsatira zosafunikira, zomwe ndizowopsa pazida.
• Kuwunika kwautali ndi kuwongolera mizere kungayambitse malupu okhudzana ndi magetsi omwe amagawana nawo, zomwe zimayambitsa kusokonezeka pakugwira ntchito kwa zipangizo, kuphatikizapo kulankhulana kwakunja. Ndi bwino kugwiritsa ntchito galvanic separators.
• Kuti muteteze mizere yolumikizirana ndi magineti yakunja, gwiritsani ntchito zingwe zotetezedwa bwino ndi mikanda ya ferrite.
• Kusintha kwamagetsi otulutsa a digito a katundu wamkulu (kupitilira momwe amafotokozera) kungayambitse kusokoneza kwamagetsi omwe amayikidwa mkati mwa chinthucho. Choncho, tikulimbikitsidwa kugwiritsa ntchito ma relay / ma contactor akunja, ndi zina zotero kuti musinthe katundu wotere. Kugwiritsiridwa ntchito kwa olamulira okhala ndi zotsatira za triac kumachepetsanso kuwonjezereka kofananatagndi zochitika.
• Nthawi zambiri zosokoneza ndi kuchulukirachulukiratage in control systems amapangidwa ndi masinthidwe, inductive katundu woperekedwa ndi alternating mains vol.tage (AC 120/230 V). Ngati alibe mabwalo oyenera ochepetsera phokoso, ndi bwino kugwiritsa ntchito mabwalo akunja monga snubbers, varistors, kapena ma diode oteteza kuti achepetse izi.

Kuyika magetsi kwa mankhwalawa kuyenera kuchitidwa motsatira malamulo a wiring a dziko ndikugwirizana ndi malamulo a m'deralo.

iSMA CONTROLLI SpA – Via Carlo Levi 52, 16010 Sant'Olcese (GE) – Italy | support@ismacontrolli.com

www.ismacontrolli.com Upangiri Woyika| 1st Rev. 1 | 05/2022

Zolemba / Zothandizira

iSMACONTROLLI SFAR-1M-2DI1AO 2 Zolowetsa Pakompyuta ndi Module 1 ya Analogi Yotulutsa Modbus IO [pdf] Buku la Malangizo SFAR-1M-2DI1AO, Zolowetsa Zapa digito 2 ndi 1 Analog Output Modbus IO Module, 1 Analogi Output Modbus IO Module, Output Modbus IO Module, Modbus IO Module, SFAR-1M-2DI1AO, Module

Maumboni

• Buku Logwiritsa Ntchito