Manwal għall-Utent

VLVWIP2000-ENC
VLVWIP2000-DIĊ

Enkoder u Dekoder JPEG2000 AVoIP

Id-Drittijiet Kollha Riservati

Version: VLVWIP2000-ENC_2025V1.0

Version: VLVWIP2000-DEC_2025V1.0

Enkoder u Dekoder JPEG2000 AVoIP

---

Prefazju

Aqra dan il-manwal tal-utent bir-reqqa qabel tuża l-prodott. L-istampi murija f'dan il-manwal huma għal referenza biss. Mudelli u speċifikazzjonijiet differenti huma suġġetti għal prodott reali.

Dan il-manwal huwa biss għall-istruzzjoni tat-tħaddim, jekk jogħġbok ikkuntattja lid-distributur lokali għall-assistenza tal-manutenzjoni. Fl-isforz kostanti biex intejbu l-prodott, aħna nirriżervaw id-dritt li nagħmlu bidliet fil-funzjonijiet jew fil-parametri mingħajr avviż jew obbligu. Jekk jogħġbok irreferi għan-negozjanti għall-aħħar dettalji.

Dikjarazzjoni tal-FCC

Dan it-tagħmir jiġġenera, juża u jista 'jirradja enerġija ta' frekwenza tar-radju u, jekk mhux installat u użat skont l-istruzzjonijiet, jista 'jikkawża interferenza ta' ħsara għall-komunikazzjonijiet bir-radju. Ġie ttestjat u nstab li jikkonforma mal-limiti għal apparat diġitali tal-Klassi B, skont il-parti 15 tar-Regoli tal-FCC. Dawn il-limiti huma mfassla biex jipprovdu protezzjoni raġonevoli kontra interferenza dannuża f'installazzjoni kummerċjali.

It-tħaddim ta 'dan it-tagħmir f'żona residenzjali x'aktarx li jikkawża interferenza, f'liema każ l-utent bi spejjeż tiegħu se jkun meħtieġ li jieħu kwalunkwe miżuri li jistgħu jkunu meħtieġa biex jikkoreġu l-interferenza.

Kwalunkwe tibdil jew modifika mhux approvata espressament mill-fabbrikazzjoni tkun nulla l-awtorità tal-utent biex iħaddem it-tagħmir.

                      

PREKAWZJONIJIET TA' SIGURTÀ

Biex tiżgura l-aħjar prestazzjoni mill-prodott, jekk jogħġbok aqra l-istruzzjonijiet kollha bir-reqqa qabel tuża l-apparat. Ħlief dan il-manwal għal aktar referenza.

• Spakkja t-tagħmir bir-reqqa u ssalva l-kaxxa oriġinali u l-materjal tal-ippakkjar għal vjeġġ futur possibbli.
• Segwi l-prekawzjonijiet bażiċi tas-sigurtà biex tnaqqas ir-riskju ta’ nar, xokk elettriku u korriment lill-persuni.
• Żarmax il-housing jew timmodifikax il-modulu. Jista 'jirriżulta f'xokk elettriku jew ħruq.
• L-użu ta' provvisti jew partijiet li ma jissodisfawx l-ispeċifikazzjonijiet tal-prodotti jista' jikkawża ħsara, deterjorament jew ħsara.
• Irreferi l-manutenzjoni kollha lil persunal tas-servizz kwalifikat.
• Biex tevita l-periklu tan-nar jew xokk, tesponix l-unità għax-xita, umdità jew tinstalla dan il-prodott ħdejn l-ilma.
• Tpoġġix xi oġġetti tqil fuq il-kejbil ta 'estensjoni f'każ ta' estrużjoni.
• Tneħħix il-housing tal-apparat peress li l-ftuħ jew it-tneħħija tal-housing jistgħu jesponuk għal vol perikolużitage jew perikli oħra.
• Installa l-apparat f'post b'ventilazzjoni fina biex tevita ħsara kkawżata minn sħana żejda.
• Żomm il-modulu 'l bogħod mil-likwidi.
• It-tixrid fl-akkomodazzjoni jista' jirriżulta f'nar, xokk elettriku, jew ħsara fit-tagħmir. Jekk oġġett jew likwidu jaqa 'jew jinxtered fuq il-housing, aqla' l-modulu immedjatament.
• M'għandekx iddawwar jew tiġbed b'forza t-truf tal-kejbil ottiku. Jista 'jikkawża ħsara.
• Tużax prodotti li jnaddfu likwidi jew aerosol biex tnaddaf din l-unità. Dejjem aqla 'l-enerġija għall-apparat qabel it-tindif.
• Aqla 'l-korda tad-dawl meta ma tintużax għal perjodu twil ta' żmien.
• Tagħrif dwar ir-rimi għal apparat skrappjat: taħraqx jew tħallat ma' skart domestiku ġenerali, jekk jogħġbok ittrattahom bħala skart elettriku normali.

Grazzi talli xtrajt dan il-prodott

Għal prestazzjoni u sigurtà ottimali, jekk jogħġbok aqra dawn l-istruzzjonijiet bir-reqqa qabel ma tqabbad, tħaddem jew taġġusta dan il-prodott. Jekk jogħġbok żomm dan il-manwal għal referenza futura.

Apparat ta 'protezzjoni minn surge rakkomandat

Dan il-prodott fih komponenti elettriċi sensittivi li jistgħu jiġu mħassra minn spikes elettriċi, żidiet, xokk elettriku, strajks tad-dawl, eċċ. L-użu ta 'sistemi ta' protezzjoni minn surge huwa rakkomandat ħafna sabiex tipproteġi u testendi l-ħajja tat-tagħmir tiegħek.

1. Introduzzjoni

This product is based on JPEG2000 technology. It integrates Copper port and Fiber port within a single box. Encoder input supports up to 4K60 4:4:4, audio embedding or extracting. Decoder output supports up to 4K60 4:4:4, audio extracting. The product supports ARC/eARC/S/PDIF/Analog audio return function, also supports USB2.0/KVM/Camera, 1G Ethernet, bidirectional RS-232, two-way IR and POE function. Guest mode controls of RS-232, IR, CEC are supported. Built-in two channel RELAY ports and two channel I/O ports for contact control. Dante AV-A mode is supported if the product is license activated.

Substream MJPEG inkorporat li jappoġġa ħafna kmandi tal-API biex jinkisbu konfigurazzjonijiet flessibbli huwa utli għall-Apps ta' kontroll ta' partijiet terzi biex qabelview kontenut tal-vidjo.

Is-sistema hija bbażata fuq Linux għall-iżvilupp tas-softwer, tipprovdi metodi ta 'kontroll flessibbli, li huma bbażati fuq in-netwerking intelliġenti ta' 1G Ethernet Switch.

2. Karatteristiċi

☆ HDCP 2.2 konformi
☆ Appoġġ bandwidth tal-vidjo 18Gbps
☆ Input and output video resolution is up to 4K60 4:4:4, as specified in HDMI 2.0b
☆ Id-distanza tat-trażmissjoni tas-sinjal tista 'tiġi estiża sa 328ft / 100m permezz tal-kejbil CAT5E/6/6A/7
☆ Transmit video, analog/digital audio, IR , RS-232, CEC and USB over Ethernet
☆ Integra l-port tar-ram u l-port tal-Fibra f'kaxxa waħda
☆ ARC/eARC/S/PDIF/Analog audio return function
☆ Dante AV-A mode is supported if license activated
☆ Konfigurazzjoni tal-kanal permezz ta 'buttuni tal-pannell ta' quddiem u skrin LED
☆ Built-in two channel RELAY ports and two channel I/O ports for contact control
☆ Appoġġ funzjonijiet unicast u multicast
☆ Appoġġ punt għal punt, matriċi tal-vidjo u funzjonijiet tal-ħajt tal-vidjo (ħajt tal-vidjo jappoġġja sa 9 × 9)
☆ Ġestjoni intelliġenti tal-klassi tal-ħajt tal-vidjo
☆ Appoġġ MJPEG Substream f'ħin reali minn qabelview
☆ 1G Ethernet Switch
☆ Appoġġ il-funzjoni POE
☆ Inkorporat web konfigurazzjoni u kontroll tal-paġna, Telnet u SSH ukoll
☆ Formati tal-awdjo HDMI: LPCM 2.0/5.1/7.1CH, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-96/24, DTS-EX DSD, DTS High Res, DTS-HD Master
☆ Disinn ta 'netwerking intelliġenti għal installazzjoni faċli u flessibbli

3. Kontenut tal-Pakkett

Qty	Oġġett
1	4K60 fuq IP 1GbE Encoder
1	Kejbil tar-riċevitur IR (1.5 metri)
1	Kejbil IR Blaster (1.5 metri)
3	Konnettur Phoenix 3-pin 3.81mm
2	Konnettur Phoenix 4-pin 3.81mm
1	12V / 2.5A Adapter tal-Enerġija li tissakkar
2	Widna tal-immuntar
4	Kamin tal-magna (KM3 * 4)
1	Manwal għall-Utent

or

Qty	Oġġett
1	4K60 fuq IP 1GbE Decoder
1	Kejbil tar-riċevitur IR (1.5 metri)
1	Kejbil IR Blaster (1.5 metri)
3	Konnettur Phoenix 3-pin 3.81mm
2	Konnettur Phoenix 4-pin 3.81mm
1	12V / 2.5A Adapter tal-Enerġija li tissakkar
2	Widna tal-immuntar
4	Kamin tal-magna (KM3 * 4)
1	Manwal għall-Utent

4. Speċifikazzjonijiet

Tekniku

Konformi HDMI	HDMI 2.0b
Konformi HDCP	HDCP 2.2
Vidjo tal-Bandwidth	18Gbps
Standard tal-Kompressjoni tal-Vidjo	JPEG2000
Bandwidth tan-Netwerk tal-Vidjo	1G
Riżoluzzjoni tal-vidjo	Sa 4K@60Hz 4:4:4
Profond tal-Kulur	Input: 8/10/12-bit Output: 8-bit
Spazju tal-Kulur	RGB 4:4:4, YCbCr 4:4:4 / 4:2:2 / 4:2:0
Formati tal-Awdjo HDMI	LPCM 2.0/5.1/7.1CH, Dolby Digital/Plus/EX, Dolby True HD, DTS, DTS-96/24, DTS-EX DSD, DTS High Res, DTS-HD Master
Distanza tat-Trażmissjoni	100M CAT5E/6/6A/7
Livell IR	Default 12V, 5V mhux obbligatorju
Frekwenza IR	Wideband 20K – 60KHz
Protezzjoni ESD	IEC 61000-4-2: ± 8kV (iskarigu ta 'l-arja) & ± 4kV (Ħruġ f'kuntatt)

Konnessjoni

Encoder

Input: 1 x HDMI IN [Type A, 19-pin female] 1 x L/R AUDIO IN [3-pin 3.81mm Phoenix connector] Output: 1 x HDMI OUT [Type A, 19-pin female] 1 x L/R AUDIO OUT [3-pin 3.81mm Phoenix connector] 1 x SPDIF OUT [Optical audio connector] Control: 1 x RS-232 [3-pin 3.81mm Phoenix connector] 1 x LAN (POE) [RJ45 jack] 1 x FIBER [Optical fiber slot] 1 x USB 2.0 HOST [Type B, 4-pin female] 2 x USB 2.0 DEVICE [Type-A, 4pin female] 2 x RELAYS [3.81mm Phoenix connector] 2 x DIGITAL IO [3.81mm Phoenix connector] 1 x IR IN [3.5mm Audio Jack] 1 x IR OUT [3.5mm Audio Jack]

Dekoder

Input: 1 x SPDIF IN [Optical audio connector] 1 x L/R AUDIO IN [3-pin 3.81mm Phoenix connector] Output: 1 x HDMI OUT [Type A, 19-pin female] 1 x L/R AUDIO OUT [3-pin 3.81mm Phoenix connector] Control: 1 x RS-232 [3.81mm Phoenix connector] 1 x LAN (POE) [RJ45 jack] 1 x FIBER [Optical fiber slot] 2 x USB 1.1 DEVICE [Type-A, 4-pin female] 2 x USB 2.0 DEVICE [Type-A, 4-pin female] 2 x RELAYS [3.81mm Phoenix connector] 2 x DIGITAL IO [3.81mm Phoenix connector] 1 x IR IN [3.5mm Audio Jack] 1 x IR OUT [3.5mm Audio Jack]

Mekkaniċi

Djar	Egħluq tal-metall
Kulur	Iswed
Dimensjonijiet	Encoder/Decoder: 204mm [W] x 136mm [D] x 25.5mm [H]
Piż	Encoder: 631g, Decoder: 626g
Provvista tal-Enerġija	Input: AC100 – 240V 50/60Hz, Output: DC 12V/2.5A (standards ta 'l-Istati Uniti/UE, iċċertifikati CE/FCC/UL)
Konsum tal-Enerġija	Encoder: 8.52W, Decoder: 7.08W (Max.)
Temperatura operattiva	32 - 104 ° F / 0 - 40 ° C
Temperatura tal-Ħażna	-4 - 140 ° F / -20 - 60 ° C
Umdità Relattiva	20 – 90% RH (l-ebda kondensazzjoni)

Riżoluzzjoni / Tul tal-Kejbil	4K60 - Saqajn / Meters	4K30 - Saqajn / Meters	1080P60 – Saqajn / Meters
HDMI IN / OUT	16ft / 5M	32ft / 10M	50ft / 15M
L-użu ta 'kejbil "Premium High Speed ​​HDMI" huwa rakkomandat ħafna.

5. Kontrolli u Funzjonijiet tal-Operazzjoni

5.1 Panel tal-Encoder

Nru.	Isem	Deskrizzjoni tal-Funzjoni
1	RESET	Wara li tixgħel l-apparat, agħfas u żomm il-buttuna RESET sakemm il-POWER LED u LINK LED jteptpu fl-istess ħin, itlaq il-buttuna biex tirrisettja l-apparat għas-settings tal-fabbrika.
2	LED QAWWA (Aħmar)	Dawl mixgħul: Is-sistema hija mixgħula (bil-provvista ta 'enerġija POE jew DC). Dawl mitfi: Is-sistema hija mitfija (mingħajr provvista ta 'enerġija POE jew DC).
3	LINK LED (Aħdar)	LED tal-istatus tal-konnessjoni.  Dawl mixgħul: Encoder u Decoder huma konnessi permezz tal-portijiet LAN(POE)/FIBER, u hemm sinjal tal-vidjo trasmess lid-Decoder.  Dawl fwawar: Encoder u Decoder huma konnessi permezz tal-portijiet LAN(POE)/FIBER, iżda m'hemm l-ebda sinjal tal-vidjo trasmess lid-Decoder.  Dawl mitfi: Encoder u Decoder mhumiex konnessi permezz tal-portijiet LAN(POE)/FIBER.
4	Skrin LED	Juri l-ID tal-Encoder bħala default. Juri l-għażliet korrispondenti tal-funzjonijiet tal-konfigurazzjoni waqt l-issettjar tal-konfigurazzjonijiet tal-Encoder.
5	CH AGĦŻEL	Użat biex tissettja l-ID tal-Encoder u settings oħra.
6	APPARAT USB 2.0	Qabbad ma 'apparat USB 2.0.
7	USB HOST	Konnettur USB-B għall-konnessjoni ta 'PC.
8	IR OUT	Port tal-ħruġ tas-sinjal IR. Il-livell IR jista 'jiġi ssettjat għal 5V jew 12V (default) permezz tal-buttuni tal-pannelli.
9	IR IN	Port tad-dħul tas-sinjal IR. Il-livell IR jista 'jiġi ssettjat għal 5V jew 12V (default) permezz tal-buttuni tal-pannelli.
10	RELAYS I DIĠITALI IO	VCC: Power output (12V or 5V configurable), maximum to 12V @50mA, 5V@ 100mA loading. The default output is 12V. RELAYS: 2 kanali b'volum baxxtage portijiet relay, kull grupp huwa indipendenti u iżolati, massimu għal tagħbija 1A 30VDC. Il-kuntatti huma skonnettjati awtomatikament. IO DIĠITALI: 2 portijiet GPIO tal-kanali, għall-kontroll tal-ħruġ tas-sinjali ta 'livell diġitali jew skoperta ta' input (sa skoperta ta 'livell ta' 12V). Il-mod ta 'kontroll tal-output (mod default, livell baxx bħala output default) jew il-mod ta' skoperta tal-input huwa konfigurabbli. Il-DIGITAL IO intern pull-up voltage issegwi l-VCC. Mod ta 'kontroll tal-output: a. Il-kurrent massimu li jiflaħ sink huwa 50mA meta joħroġ livell baxx. b. Meta VCC huwa 5V u livell għoli huwa output, il-kapaċità massima tas-sewqan kurrenti hija 2mA. c. Meta VCC huwa 12V u livell għoli huwa output, il-kapaċità massima tas-sewqan kurrenti hija 5mA. Modalità ta' skoperta tad-dħul: a. Meta VCC huwa 5V, DIĠITALI IO jinġibed sa 5V internament permezz ta 'reżistenza 2.2K ohm. b. Meta VCC huwa 12V, DIĠITALI IO jinġibed sa 12V internament permezz ta 'reżistenza 2.2K ohm.
11	RS-232	Port tas-serje RS-232, li jappoġġja l-pass-through tal-kmand RS-232 u l-kontroll lokali tal-port tas-serje.
12	AWDJO IN/OUT	AUDIO IN: Analog audio input port, the audio can be embedded into the HDMI signal for pass-through over to HDMI output and audio out on Decoder, or be loop out by the AUDIO OUT port on Encoder.
		AUDIO OUT: Analog audio output port. It can output the audio extracted from the HDMI IN port (in case of LPCM) . Also it can output the audio transmitted from the AUDIO IN port of the Decoder in unicast mode (point-to-point direct connection).
13	SPDIF OUT	S/PDIF signal output port. It can output the ARC or S/PDIF audio returned from the Decoder when both the Encoder and Decoder are correspondingly set to the ARC or S/PDIF audio return mode (Set through the Controller Box or API commands in Multicast mode; Set through the front panel buttons in unicast mode).
14	HDMI OUT	Port tal-ħruġ tal-loop lokali HDMI, imqabbad ma 'apparat tal-wiri HDMI bħal TV jew monitor.
15	HDMI-IN	Port tad-dħul tas-sinjal HDMI, imqabbad ma 'apparat tas-sors HDMI bħal Blu-ray Player jew Set-top box b'kejbil HDMI.
16	FIBRA	Qabbad mal-modulu tal-fibra ottika, u jittrasmetti sinjali lid-Decoder b'kejbil tal-fibra ottika direttament jew permezz ta 'Swiċċ.
17	LAN (POE)	Port LAN 1G, qabbad in-netwerk Aqleb biex tifforma sistema distribwita. Nota: Meta l-iswiċċ tan-netwerk jagħti provvista ta 'enerġija POE, l-adapter DC 12V m'għandux għalfejn japplika fuq l-unità.
18	Indikatur tas-Sinjal tad-Dejta lamp (Isfar)	Light flashing: There is data transmission. ▪ Light off: There is no data transmission.
19	Link Indikatur tas-Sinjal lamp (aħdar)	Light on: The network cable is connected normally. ▪ Light off: The network cable is not connected well.
20	DC 12V	L-apparat jista’ jitħaddem permezz ta’ żewġ metodi: Provvista ta 'enerġija lokali DC 12V/2.5A  POE minn Network Switch. L-apparat jaġixxi bħala mod PD. When the Switch supports POE function, DC power supply is not needed.

Deskrizzjoni tat-tħaddim tal-iskrin LED u buttuni CH SELECT (Għal Encoder).

1, ID ENC: Wara li s-sistema tkun mixgħula, l-iskrin LED tal-Encoder se juri l-ENC ID (000 b'mod awtomatiku jekk mhux issettjat).

2, Indirizz IP: Agħfas u żomm il-buttuna UP għal 5 sekondi, l-iskrin LED tal-Encoder se juri f'sekwenza "IPx", "xxx", "xxx", "xxx", "xxx", li huma l-modalità IP u l-indirizz IP tal-Encoder.

3, Mod ta 'konfigurazzjoni: Agħfas u żomm il-buttuni UP + DOWN fl-istess ħin għal 5 sekondi, imbagħad erħi biex tidħol fil-mod ta 'konfigurazzjoni b'"CFN" murija fuq l-iskrin LED.

4, Issettjar tal-ID tal-apparat: After entering the configuration mode, press the UP/DOWN button to enter the first page with the current ID number (e.g. 001) displaying on the LED screen (000 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the ID settings mode, in which the ID number (e.g. 001) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the device ID you desired (ID range: 000~762), then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
Nota: L-ID tal-apparat ma jistax jiġi modifikat fil-modalità tal-Kaxxa tal-Kontrollur.

5, Settings EDID: After entering the configuration mode, press the UP/DOWN button to enter the second page with “E00” (in which “E” refers to EDID, “00” to EDID ID) or “COP” (which indicates copy EDID) displaying on the LED screen (E15 by default).
Press and hold UP + DOWN buttons for 5 seconds, then release to enter the EDID settings mode, in which the EDID ID number (e.g. E01) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the EDID ID you desired, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing.
L-ID EDID korrispondenti hija kif ġej:

ID EDID	Deskrizzjoni EDID
E00	1080P_Stereo_Audio_2.0_SDR
E01	1080P_DolbyDTS_5.1_SDR
E02	1080P_HD_Audio_7.1_SDR
E03	1080I_Stereo_Audio_2.0_SDR
E04	1080I_DolbyDTS_5.1_SDR
E05	1080I_HD_Audio_7.1_SDR
E06	3D_Stereo_Audio_2.0_SDR
E07	3D_DolbyDTS_5.1_SDR
E08	3D_HD_Audio_7.1_SDR
E09	4K2K30_444_Stereo_Audio_2.0_SDR
E10	4K2K30_444_DolbyDTS_5.1_SDR
E11	4K2K30_444_HD_Audio_7.1_SDR
E12	4K2K60_420_Stereo_Audio_2.0_SDR
E13	4K2K60_420_DolbyDTS_5.1_SDR
E14	4K2K60_420_HD_Audio_7.1_SDR
E15	4K2K60_444_Stereo_Audio_2.0_SDR
E16	4K2K60_444_DolbyDTS_5.1_SDR
E17	4K2K60_444_HD_Audio_7.1_SDR
E18	4K2K60_444_Stereo_Audio_2.0_HDR_10-bit
E19	4K2K60_444_DolbyDTS_5.1_HDR_10-bit
E20	4K2K60_444_HD_Audio_7.1_HDR_10-bit
E21	DVI_1280x1024
E22	DVI_1920x1080
E23	DVI_1920x1200

Nota: In point to point connection mode, before using the EDID copy function, all codecs need to be set to CA1 unicast mode, and after setting, the HDMI cable of the Decoder needs to be re-plugged to report the EDID of TV to the Encoder.

6, Issettjar tal-modalità IR: After entering the configuration mode, press the UP/DOWN button to enter the third page with “IR2” (in which “IR” refers to IR and “2” to 12V) displaying on the LED screen (IR2 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the IR mode (IR1 or IR2) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the IR mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing.
The corresponding IR mode options are as follows:
IR1: wajer IR 5V
IR2: wajer IR 12V

7, Audio embedding mode settings: After entering the configuration mode, press the UP/DOWN button to enter the fourth page with “HDI/ANA” displaying on the LED screen (HDI by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the audio return mode (HDI/ANA) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing.
The corresponding audio embedding mode options are as follows:
HDI: HDMI audio embedding
ANA: Analog audio embedding

8, Issettjar tal-modalità IP: After entering the configuration mode, press the UP/DOWN button to enter the fifth page with “IP1/IP2/IP3” displaying on the LED screen (IP3 by default).
Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the IP mode (IP1/IP2/IP3) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding IP mode options are as follows:
IP1: Static IP mode (Default IP address: 169.254.100.254)
IP2: Modalità DHCP IP
IP3: Auto IP mode (Default assigned network segment: 169.254.xxx.xxx)
Note: The IP mode can not be modified in Controller Box mode.

9, Fiber/Copper mode settings: After entering the configuration mode, press the UP/DOWN button to enter the sixth page with “CPP/FIB” displaying on the LED screen (CPP by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the Fiber/Copper mode (CPP/FIB) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding Fiber/Copper mode options are as follows:
CPP: Copper mode
FIB: Fiber mode

10, Multicast mode settings: After entering the configuration mode, press the UP/DOWN button to enter the seventh page with “CA1/CA2” displaying on the LED screen (CA1 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the multicast mode (CA1/CA2) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding multicast mode options are as follows:
CA1: Unicast mode
CA2: Multicast mode

11, Issettjar tal-modalità tar-ritorn tal-awdjo: After entering the configuration mode, press the UP/DOWN button to enter the eighth page with “C2C/A2A” displaying on the LED screen (C2C by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the audio return mode (C2C/A2A) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding audio return mode options are as follows:
C2C: The eARC/ARC or S/PDIF audio from the Decoder is transmitted back to the HDMI IN or SPDIF OUT port of the Encoder.
A2A: The analog audio embedded in the Decoder is transmitted back to the AUDIO OUT analog audio port of the Encoder.

Nota:
(1) Il-mod ta 'ritorn tal-awdjo ma jistax jiġi modifikat permezz tal-buttuni tal-pannell ta' quddiem fil-Kaxxa tal-Kontrollur jew il-modalità Multicast.
(2) Only when both the Encoder and Decoder are correspondingly set to C2C/A2A audio return mode in unicast mode, the audio return can be realized.
(3) The A2A audio return mode is available only in unicast mode.
(4) Meta tuża ARC, awdjo ARC amplifier fuq Encoder HDMI IN port u ARC TV fuq Decoder HDMI OUT port għandhom jintużaw.
Meta tuża eARC, awdjo eARC ampgħandhom jintużaw lifier fuq il-port Encoder HDMI IN u eARC TV fuq il-port Decoder HDMI OUT.
(5) Wara li ddaħħal diversi modi ta 'issettjar, tista' żżomm il-buttuna DOWN biex toħroġ malajr mill-interface kurrenti, jew jekk ma twettaq l-ebda operazzjoni fi żmien 5 sekondi, awtomatikament terġa 'lura għall-interface ta' qabel.

5.2 Panel tad-Decoder

Nru.	Isem	Deskrizzjoni tal-Funzjoni
1	RESET	Wara li tixgħel l-apparat, agħfas u żomm il-buttuna RESET sakemm il-POWER LED u LINK LED jteptpu fl-istess ħin, itlaq il-buttuna biex tirrisettja l-apparat għas-settings tal-fabbrika.
2	LED QAWWA (Aħmar)	Dawl mixgħul: Is-sistema hija mixgħula (bil-provvista ta 'enerġija POE jew DC).  Dawl mitfi: Is-sistema hija mitfija (mingħajr provvista ta 'enerġija POE jew DC).
3	LINK LED (Aħdar)	LED tal-istatus tal-konnessjoni.  Dawl mixgħul: Encoder u Decoder huma konnessi permezz tal-portijiet LAN(POE)/FIBER, u hemm sinjal tal-vidjo trasmess mill-Encoder.  Dawl fwawar: Encoder u Decoder huma konnessi permezz tal-portijiet LAN(POE)/FIBER, iżda m'hemm l-ebda sinjal tal-vidjo trasmess mill-Encoder.  Dawl mitfi: Encoder u Decoder mhumiex konnessi permezz tal-portijiet LAN(POE)/FIBER.
4	Skrin LED	Juri l-ID tal-Encoder magħżul bħala default. Juri l-għażliet korrispondenti tal-funzjonijiet tal-konfigurazzjoni waqt l-issettjar tal-konfigurazzjonijiet tad-Decoder.
5	CH AGĦŻEL	Użat biex tissettja l-ID tad-Decoder u settings oħra.
6	APPARAT USB 1.1	Qabbad ma 'apparat USB 1.1, bħal Keyboard jew Mouse.
7	APPARAT USB 2.0	Qabbad ma 'apparat USB 2.0, bħal USB flash disk jew USB Camera.
8	IR OUT	Port tal-ħruġ tas-sinjal IR. Il-livell IR jista 'jiġi ssettjat għal 5V jew 12V (default) permezz tal-buttuni tal-pannelli.
9	IR IN	Port tad-dħul tas-sinjal IR. Il-livell IR jista 'jiġi ssettjat għal 5V jew 12V (default) permezz tal-buttuni tal-pannelli.
10	RELAYS I DIĠITALI IO	VCC: Output ta 'enerġija (12V jew 5V konfigurabbli), massimu għal 12V@50mA, 5V@ 100mA tagħbija. L-output default huwa 12V. RELAYS: 2 kanali b'volum baxxtage portijiet relay, kull grupp huwa indipendenti u iżolati, massimu għal tagħbija 1A 30VDC. Il-kuntatti huma skonnettjati awtomatikament. DIGITAL IO: 2 channel GPIO ports, for digital level signal output control or input detection (up to 12V level detection). The output control mode (default mode, low level as default output) or input detection mode is configurable. The DIGITAL IO internal pull-up voltage issegwi l-VCC. Mod ta 'kontroll tal-output: a. Il-kurrent massimu li jiflaħ sink huwa 50mA meta joħroġ livell baxx. b. Meta VCC huwa 5V u livell għoli huwa output, il-kapaċità massima tas-sewqan kurrenti hija 2mA. c. Meta VCC huwa 12V u livell għoli huwa output, il-kapaċità massima tas-sewqan kurrenti hija 5mA. Modalità ta' skoperta tad-dħul: a. Meta VCC huwa 5V, DIĠITALI IO jinġibed sa 5V internament permezz ta 'reżistenza 2.2K ohm. b. Meta VCC huwa 12V, DIĠITALI IO jinġibed sa 12V internament permezz ta 'reżistenza 2.2K ohm.
11	RS-232	Port tas-serje RS-232, li jappoġġja l-pass-through tal-kmand RS-232 u l-kontroll lokali tal-port tas-serje.
12	AWDJO IN/OUT	AUDIO IN: Port ta 'input ta' l-awdjo analogu, l-awdjo jista 'jiġi trażmess lil Encoder AUDIO OUT fil-mod unicast (konnessjoni diretta minn punt għal punt).
		AUDIO OUT: Port tal-ħruġ tal-awdjo analogu. Jipproduċi l-istess awdjo ta 'dak fuq HDMI OUT f'każ li l-format awdjo huwa LPCM.
13	SPDIF FI	Port tad-dħul tas-sinjal S/PDIF.
14	HDMI OUT	Port tal-ħruġ tas-sinjal HDMI, imqabbad ma 'apparat tal-wiri HDMI bħal TV jew monitor.
15	FIBRA	Qabbad ma 'modulu tal-fibra ottika, u tirċievi sinjali mill-Encoder b'kejbil tal-fibra ottika direttament jew permezz ta' Swiċċ.
16	LAN (POE)	Port LAN 1G, qabbad in-netwerk Aqleb biex tifforma sistema distribwita. Nota: Meta l-iswiċċ tan-netwerk jagħti provvista ta 'enerġija POE, l-adapter DC 12V m'għandux għalfejn japplika fuq l-unità.
17	Indikatur tas-Sinjal tad-Dejta lamp (Isfar)	Dawl li jteptep: Hemm trażmissjoni tad-dejta.  Dawl mitfi: M'hemm l-ebda trażmissjoni tad-dejta.
18	Link Indikatur tas-Sinjal lamp (aħdar)	Dawl mixgħul: Il-kejbil tan-netwerk huwa konness b'mod normali.  Dawl mitfi: Il-kejbil tan-netwerk mhuwiex konness sew.
19	DC 12V	L-apparat jista’ jitħaddem permezz ta’ żewġ metodi:  Provvista ta 'enerġija lokali DC 12V/2.5A  POE minn Network Switch. L-apparat jaġixxi bħala mod PD. When the Switch supports POE function, DC power supply is not needed.

Deskrizzjoni tat-tħaddim tal-iskrin LED u buttuni CH SELECT (Għal Decoder).

1, Konnessjoni ENC: Wara li s-sistema tkun mixgħula, l-iskrin LED tad-Decoder se juri 000 awtomatikament jekk mhux issettjat. Agħfas direttament il-buttuna UP/DOWN biex tagħżel l-ID tal-kanal tal-Encoder konness (firxa tal-ID: 000 ~ 762) biex tlesti l-konnessjoni.

2, Indirizz IP: Agħfas u żomm il-buttuna UP għal 5 sekondi, l-iskrin LED tad-Decoder se juri f'sekwenza "IPx", "xxx", "xxx", "xxx", "xxx", li huma l-modalità IP u l-indirizz IP tad-Decoder.

3, Mod ta 'konfigurazzjoni: Agħfas u żomm il-buttuni UP + DOWN fl-istess ħin għal 5 sekondi, imbagħad erħi biex tidħol fil-mod ta 'konfigurazzjoni b'"CFN" murija fuq l-iskrin LED.

4, Issettjar tal-ID tal-apparat: After entering the configuration mode, press the UP/DOWN button to enter the first page with the current ID number (e.g. 001) displaying on the LED screen (000 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the ID settings mode, in which the ID number (e.g. 001) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the device ID you desired (ID range: 000~762), then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
Nota: L-ID tal-apparat ma jistax jiġi modifikat fil-modalità tal-Kaxxa tal-Kontrollur.

5, Output scaling settings: After entering the configuration mode, press the UP/DOWN button to enter the second page with “S00” (in which “S” refers to Scaling, and “00” to resolution ID) displaying on the LED screen (S00 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the Sxx on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the ID you desired, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing.
The scaling settings are listed below:

Scaling Sxx	Deskrizzjoni tar-Riżoluzzjoni
S00	bypass
S01	1080P50
S02	1080P60
S03	720P50
S04	720P60
S05	2160P24
S06	2160P30
S07	2160P50
S08	2160P60
S09	1280×1024
S10	1360×768
S11	1440×900
S12	1680×1050
S13	1920×1200

6, Issettjar tal-modalità IR: After entering the configuration mode, press the UP/DOWN button to enter the third page with “IR2” (in which “IR” refers to IR and “2” to 12V) displaying on the LED screen (IR2 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the IR mode (IR1 or IR2) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the IR mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing.
The corresponding IR mode options are as follows:
IR1: wajer IR 5V
IR2: wajer IR 12V

7, eARC/ARC or S/PDIF audio return settings: After entering the configuration mode, press the UP/DOWN button to enter the fourth page with “ARC/SPD” displaying on the LED screen (ARC by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the audio return settings mode, in which the audio return mode (ARC/SPD) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. The corresponding audio return mode options are as follows:
ARC: eARC/ARC audio return (The audio from the HDMI OUT port of Decoder is transmitted back to the HDMI IN port of the Encoder.)
SPD: S/PDIF audio return (The audio from the S/PDIF IN port of Decoder is transmitted back to the S/PDIF OUT port of the Encoder.)
Nota:
(1) Il-mod ta 'ritorn tal-awdjo ma jistax jiġi modifikat permezz tal-buttuni tal-pannell ta' quddiem fil-Kaxxa tal-Kontrollur jew il-modalità Multicast.
(2) Only when both the Encoder and Decoder are set to C2C audio return mode, the eARC/ARC or S/PDIF audio return can be realized.
(3) Meta tuża ARC, awdjo ARC amplifier fuq Encoder HDMI IN port u ARC TV fuq Decoder HDMI OUT port għandhom jintużaw.
Meta tuża eARC, awdjo eARC ampgħandhom jintużaw lifier fuq il-port Encoder HDMI IN u eARC TV fuq il-port Decoder HDMI OUT.

8, Issettjar tal-modalità IP: After entering the configuration mode, press the UP/DOWN button to enter the fifth page with “IP1/IP2/IP3” displaying on the LED screen (IP3 by default).
Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the IP mode (IP1/IP2/IP3) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding IP mode options are as follows:
IP1: Static IP mode (Default IP address: 169.254.100.253)
IP2: Modalità DHCP IP
IP3: Auto IP mode (Default assigned network segment: 169.254.xxx.xxx)
Nota: Il-modalità IP ma tistax tiġi modifikata fil-modalità tal-Kaxxa tal-Kontrollur.

9, Fiber/Copper mode settings: After entering the configuration mode, press the UP/DOWN button to enter the sixth page with “CPP/FIB” displaying on the LED screen (CPP by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the Copper/Fiber mode (CPP/FIB) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding Fiber/Copper mode options are as follows:
CPP: Copper mode
FIB: Fiber mode

10, Multicast mode settings: After entering the configuration mode, press the UP/DOWN button to enter the seventh page with “CA1/CA2” displaying on the LED screen (CA1 by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the Multicast mode (CA1/CA2) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding multicast mode options are as follows:
CA1: Unicast mode
CA2: Multicast mode

11, Issettjar tal-modalità tar-ritorn tal-awdjo: After entering the configuration mode, press the UP/DOWN button to enter the eighth page with “C2C/A2A” displaying on the LED screen (C2C by default). Press and hold UP + DOWN buttons for 5 seconds, then release to enter the settings mode, in which the audio return mode (C2C/A2A) on the LED screen will flash at 1Hz, then press the UP/DOWN button to select the mode, then press and hold UP + DOWN buttons for 5 seconds to confirm the setting and stop flashing. After setting, the unit will reboot automatically.
The corresponding audio return mode options are as follows:
C2C: The eARC/ARC or S/PDIF audio from the Decoder is transmitted back to the HDMI IN or S/PDIF OUT port of the Encoder.
A2A: The analog audio embedded in the Decoder is transmitted back to the AUDIO OUT analog audio port of the Encoder.
Nota:
(1) Il-mod ta 'ritorn tal-awdjo ma jistax jiġi modifikat permezz tal-buttuni tal-pannell ta' quddiem fil-Kaxxa tal-Kontrollur jew il-modalità Multicast.
(2) Only when both the Encoder and Decoder are correspondingly set to C2C/A2A audio return mode in unicast mode, the audio return can be realized.
(3) The A2A audio return mode is available only in unicast mode.
(4) Meta tuża ARC, awdjo ARC amplifier fuq Encoder HDMI IN port u ARC TV fuq Decoder HDMI OUT port għandhom jintużaw.
Meta tuża eARC, awdjo eARC ampgħandhom jintużaw lifier fuq il-port Encoder HDMI IN u eARC TV fuq il-port Decoder HDMI OUT.
(5) Wara li ddaħħal diversi modi ta 'issettjar, tista' żżomm il-buttuna DOWN biex toħroġ malajr mill-interface kurrenti, jew jekk ma twettaq l-ebda operazzjoni fi żmien 5 sekondi, awtomatikament terġa 'lura għall-interface ta' qabel.

5.3 Definizzjoni tal-Pin IR

       
IR BLASTER          IR RECEIVER

IR BLASTER

IR RIĊEVITUR

(1) Sinjal IR
(2) L-ert
(3) Qawwa 12V

6. Istruzzjoni għall-Immuntar tar-Rack

6.1 Immuntar ta 'Rack 6U V2

Dan il-prodott jista 'jiġi mmuntat f'rack standard 6U V2 (Jekk jogħġbok ikkuntattja lill-fornitur tiegħek għall-bejgħ tar-rack 6U V2). Il-passi tal-immuntar huma kif ġej:

Pass 1: Uża viti inklużi biex tiffissa żewġ widnejn tal-immuntar fuq il-prodott, kif muri fil-figura hawn taħt:

Pass 2: Daħħal il-prodott bil-widnejn tal-immuntar f'rack 6U V2 (6/8/10 unitajiet jistgħu jiġu installati vertikalment), kif muri fil-figura hawn taħt:

Pass 3: Uża viti biex tiffissa l-widnejn tal-immuntar fuq ir-rack biex tlesti l-immuntar, kif muri fil-figura hawn taħt:

6.2 Immuntar ta 'Rack 1U V2

Dan il-prodott jista 'wkoll jiġi mmuntat f'rack standard 1U V2 (2 unitajiet jistgħu jiġu installati orizzontalment). Il-passi tal-immuntar huma kif ġej:

Pass 1: Uża viti inklużi biex tiffissa żewġ parentesi tar-rack 1U V2 fuq żewġ prodotti rispettivament, kif muri fil-figura hawn taħt:

Pass 2: Uża viti biex tiffissa żewġ parentesi tar-rack 1U V2 flimkien, kif muri fil-figura hawn taħt:

Pass 3: Waħħal il-viti bejn żewġ parentesi tar-rack 1U V2, sabiex żewġ prodotti jkunu mmuntati f'rack 1U V2, kif muri fil-figura hawn taħt:

7. MJPEG Substream Operazzjoni Introduzzjoni

7.1 MJPEG Substream Preview/ Konfigurazzjoni permezz Web Paġna

The product supports playing MJPEG Substream on computer through the corresponding software such as VLC media player, fl-istess ħin tista' taċċessa l- Web paġna biex tikkonfigura s-Substream MJPEG.
Segwi l-passi hawn taħt biex qabelview u kkonfigurat is-Substream MJPEG.

Pass 1: Qabbad l-Encoder, Decoder u PC ma 'l-istess Switcher, imbagħad qabbad apparat tas-sors HDMI u provvista ta' enerġija. Id-dijagramma tal-konnessjoni tidher kif hawn taħt.

1. Blu-ray Player
2. Adapter tal-Enerġija
3. Encoder
4. PC
5. Swiċċ Ethernet 1G
6. Dekoder

Pass 2: Install a bonjour protocol checking tool (such as zeroconfService Browser) on PC to find the IP address of the Encoder/Decoder.
Ħu zeroconfServiceBrowser bħala example. Wara li tiftaħ is-softwer, tista 'tagħżel "Workgroup Manager" fis-Servizzi tal-Browser, agħżel l-isem tal-Ospitanti f'Istanza tas-Servizz, u ssib l-indirizz IP fl-oġġett tal-Indirizz f'Istanza-Informazzjoni.

Nota:
(1) It-tieqa fir-rokna t'isfel tax-xellug turi l-ismijiet tal-Ospitanti tal-apparati kollha fin-netwerk attwali.
(2) The window in the lower right corner displays the Host name, IP address and Port number of the device.
(3) The Host name of Encoder starts with AST-ENC; the Host name of Decoder starts with AST-DEC.

Pass 3: Issettja l-indirizz IP tal-PC għall-istess segment tan-netwerk bl-indirizz IP tal-Encoder/Decoder misjub fil-pass 2.

Pass 4: Skont l-indirizz IP tal-Encoder/Decoder misjub permezz tal-għodda tal-iċċekkjar tal-protokoll bonjour, daħħal "http://IP:PORT/?action=stream" fil- web browser fuq il-PC. Is-Substream MJPEG se jintwera bir-riżoluzzjoni default, kif muri fil-figura hawn taħt.

Pass 5: Ibdel ir-riżoluzzjoni tal-indirizz IP tal-Encoder/Decoder miksub fil-format li ġej.
http://IP:PORT/?action=stream&w=x&h=x&fps=x&bw=x&as=x&mq=x

• WIESA: [Mhux obbligatorju] wisa' tal-immaġni. F'pixels. 'x' tfisser l-ebda bidla.
  In-nuqqas huwa 640.
• GĦOLI: [Mhux obbligatorju] għoli tal-immaġni. F'pixels. 'x' tfisser l-ebda bidla.
  In-nuqqas huwa 360.
• FRAMERATE: [Fakultattiv] rata ta' qafas tas-sub-stream.
  Unità: fps (frejm kull sekonda). 'x' tfisser l-ebda bidla. Default huwa 30.
• BW: [Fakultattiv] bandwidth massimu tat-traffiku sub-stream.
  Unità: Kbps (Kbits kull sekonda). 'x' tfisser l-ebda bidla. Default huwa 8000 (8Mbps).
• AS: [Fakultattiv] konfigurazzjoni tal-proporzjon tal-aspett. 'x' tfisser l-ebda bidla. Default huwa 0.
• 0: testendi għal dak li kkonfigurat "WIDTH" u "HEIGHT".
• 1: [A1 only] keep original aspect ratio and place in the center of output (letterboxing or pillarboxing)
• MINQ: [Fakultattiv] numru minimu tal-kwalità tal-immaġni. Firxa: 10, 20, …, 90, 100, issettjar ogħla jfisser kwalità aħjar tal-immaġni. 'x' tfisser l-ebda bidla. Il-valur default huwa 10. Limitu n-numru ta 'kwalità minimu tal-kontroll tal-bandwidth awtomatiku tas-sewwieq. Jekk kwalità aktar baxxa minn valur MINQ, is-sewwieq se jwaqqa 'qafas billi jirritorna 0 daqs file.

Wara li tbiddel, daħħal l-indirizz IP tal-Encoder/Decoder il-ġdid fil- web browser fuq il-PC, is-Substream MJPEG se jintwera bir-riżoluzzjoni mixtieqa, kif muri fil-figura hawn taħt.

7.2 Istruzzjoni tal-VLC Media Player

L-ewwelnett, wettaq il-pass 1 ~ 3 kif deskritt fil-Kapitolu 7.1, imbagħad iftaħ il-VLC media player fuq il-PC. Jekk jogħġbok ara l-ikona li ġejja.

Ikklikkja "Midja > Open Network Stream"

Wara li tikklikkja l-għażla "Open Network Stream", tidher il-paġna li ġejja.

Daħħal in-netwerk MJPEG Substream URL, imbagħad ikklikkja "Playbuttuna.

Agħżel "Għodda> Informazzjoni tal-Codec“, a pop-up window will display and show you Stream information, as shown in the figure below.

Agħżel "Għodda> Informazzjoni tal-Codec> Statistika” to check current Bitrate. Please see the following picture.

Nota: Il-Bitrate huwa f'wiċċ l-ilma 'l fuq u' l isfel meta tiċċekkjaha. Dan huwa fenomenu normali.

8. Mudell tal-Iswiċċ

Swiċċ tan-netwerk użat biex titwaqqaf is-sistema għandu jappoġġa l-karatteristiċi hawn taħt:

1. Tip ta' saff 3/netwerk immexxi Swiċċ.
2. Wiesgħa tal-frekwenza tal-gigabit.
3. Kapaċità tal-qafas jumbo ta '8KB.
4. Snooping IGMP.

Il-mudelli tal-Iswiċċ li ġejjin huma rakkomandati ħafna.

Manifattur	Numru tal-Mudell
CISCO	CISCO SG500
CISCO	Serje KATALISTI
HUAWEI	S5720S-28X-PWR-LI-AC
ZyXEL	GS2210
LUXUL	AMS-4424P

9. Kontroll tas-Sistema 4K fuq IP

Dan il-prodott jista 'jiġi kkontrollat ​​minn Kaxxa tal-Kontrollur jew kontrollur ta' parti terza. Għad-dettalji tal-kontroll tas-sistema 4K fuq IP, jekk jogħġbok irreferi għall-manwal tal-utent ta '"Kontrollur tal-vidjow fuq IP".

10. Applikazzjoni Eżample

1. ENC
2. DVD
3. Kaxxa tal-Kontrollur
4. Router (mhux obbligatorju)
5. PC
6. Swiċċ Ethernet 1G
7. 4 × DIĊ
8. Ħajt tal-vidjo
9. DIĊ
10. TV

Nota:
(1) For the default IP mode of Control LAN port of the Controller Box is DHCP, the PC also needs to be set to “Obtain an IP address automatically” mode, and a DHCP server (e.g. network router) is required in the system.
(2) If there is no DHCP server in the system, 192.168.0.225 will be used as the IP address of Control LAN port. You need to set the IP address of the PC to be in the same network segment. For example, issettja l-indirizz IP tal-PC bħala 192.168.0.88.
(3) Tista' taċċessa l- Web GUI billi ddaħħal Control LAN port IP address (192.168.0.225) jew URL “http://controller.local” fuq il-browser tal-kompjuter tiegħek.
(4) M'hemmx għalfejn tieħu ħsieb is-settings tal-port tal-Vidjo LAN tal-Kaxxa tal-Kontrollur, huma ġestiti mill-Kontrollur awtomatikament (Default).
(5) Meta l-Iswiċċ tan-Netwerk ma jappoġġjax PoE, l-Encoder, id-Decoder u l-Kaxxa tal-Kontrollur għandhom ikunu mħaddma b'adapter tal-enerġija DC.

It-termini HDMI u HDMI High-Definition Multimedia interface, u l-Logo HDMI huma trademarks jew trademarks reġistrati ta 'HDMI Licensing LLC fl-Istati Uniti u pajjiżi oħra.

Servizz tal-Klijent

Ir-ritorn ta' prodott lis-Servizz tal-Klijent tagħna jimplika l-qbil sħiħ tat-termini u l-kundizzjonijiet minn hawn 'il quddiem. Hemm termini u kundizzjonijiet jistgħu jinbidlu mingħajr avviż minn qabel.

1) Garanzija
Il-perjodu ta 'garanzija limitata tal-prodott huwa ffissat tliet snin.

2) Ambitu
Dawn it-termini u l-kundizzjonijiet tas-Servizz tal-Klijent japplikaw għas-servizz tal-klijent ipprovdut għall-prodotti jew kwalunkwe oġġett ieħor mibjugħ minn distributur awtorizzat biss.

3) Esklużjoni tal-garanzija:

• Skadenza tal-garanzija.
• Factory applied serial number has been altered or removed from the Product.
• Ħsara, deterjorament jew ħsara kkawżata minn:
  ✓ Xedd u kedd normali.
  ✓ Użu ta 'provvisti jew partijiet li ma jissodisfawx l-ispeċifikazzjonijiet tagħna.
  ✓ L-ebda ċertifikat jew fattura bħala l-prova tal-garanzija.
  ✓ Il-mudell tal-prodott muri fuq il-karta tal-garanzija ma jaqbilx mal-mudell tal-prodott għat-tiswija jew kien ġie mibdul.
  ✓ Ħsara kkawżata minn forza maġġuri.
  ✓ Servizz mhux awtorizzat mid-distributur.
  ✓ Kwalunkwe kawża oħra li ma tirrelatax ma 'difett tal-prodott.
• Ħlasijiet tal-ġarr, installazzjoni jew spejjeż tax-xogħol għall-installazzjoni jew l-issettjar tal-prodott.

4) Dokumentazzjoni:
Is-Servizz tal-Klijent se jaċċetta prodott(i) difettuż(i) fl-ambitu tal-kopertura tal-garanzija bl-unika kondizzjoni li t-telfa tkun ġiet definita b’mod ċar, u malli tirċievi d-dokumenti jew kopja tal-fattura, li tindika d-data tax-xiri, it-tip ta’ prodott, il- numru tas-serje, u l-isem tad-distributur.

Rimarki: Jekk jogħġbok ikkuntattja lid-distributur lokali tiegħek għal aktar assistenza jew soluzzjonijiet.

Dokumenti / Riżorsi

VIVO LINK JPEG2000 AVoIP Encoder and Decoder [pdfManwal tal-Utent VLVWIP2000-ENC, VLVWIP2000-DEC, JPEG2000 AVoIP Encoder and Decoder, JPEG2000, AVoIP Encoder and Decoder, Encoder and Decoder, and Decoder

Referenzi

• Manwal għall-Utent