emm Labs WiFi холболтыг хяналтын програмтай AP горимыг ашиглана
Бүтээгдэхүүний техникийн үзүүлэлтүүд
- A supported Wi-Fi adapter required
- Сүлжээний кабелийн портын доор байгаа USB порт нь адаптер суулгах зориулалттай
- Compatible with Realtek’s RTL8811AU, RTL8811CU, and RTL8812BU chipsets
- Үйлдвэрлэгч: EMM Labs / Meitner Audio
Бүтээгдэхүүнийг ашиглах заавар
- Ensure a supported Wi-Fi adapter is installed in the USB port located below the network cable port.
- If you have changed the device name, it will appear instead of ‘ProductName’.
- Download and install the Mconnect Control app on your mobile device.
- Connect your mobile device to the same Wi-Fi network as the product.
- Open the Mconnect Control app and navigate to the Play to list.
- Та тэнд жагсаасан EMM Labs/Meitner бүтээгдэхүүнийг харах ёстой.
- Once a Wi-Fi connection is established, the product will remember the network and automatically connect to it when powered on.
Жич: The Wi-Fi adapter is not provided by EMM Labs/Meitner Audio. Make sure to use one of the supported adapter chipsets mentioned above.
Дэлгэрэнгүй мэдээлэл, дэмжлэг авахыг хүсвэл зочилно уу www.emmlabs.com.
AP mode Installation guide
Access Point (AP) mode allows for devices to be added to a secure home wireless network by connecting to the camera’s temporary access point using a Wi-Fi enabled device.
AP mode installation steps
Activate AP mode on the camera:
- Connect the camera’s AC adapter and plug it into a non-switched outlet. The camera’s LED illuminates red while it is booting up. If the standard power supply is too short to reach an outlet, see How do I extend the power supply of a camera?.
- Wait for the camera to finish its startup process. This should take approximately 2 minutes for most Alarm.com video cameras.
- Press and hold the camera’s WPS button for 5 to 7 seconds. Release the button immediately after the camera’s LED starts to flash white. For more information about the typical LED status indicators for Alarm.com video devices, see What does my camera’s LED light mean?.
Жич: While holding the button, a blue LED flashes to indicate WPS mode, then a white LED flashes to indicate AP mode.
Connect the camera to the Wi-Fi network:
- Using a computer, smartphone, or tablet, connect to the Wi-Fi network named ALARM (##:##:##). The numbers in parentheses are the last six digits of the camera’s MAC address.
- Нэг төхөөрөмж дээр нээнэ үү web хөтөч хийгээд оруулна уу web address for the video device being connected (e.g., http://v723install or http://522irinstall) or 192.168.1.1 in the address bar. Follow the on-screen instructions to add the camera to the Wi-Fi network. The user interface and steps vary between video devices.
- Хүссэн хэлээ сонгохын тулд товшино уу.
- Click Scan for Wi-Fi Networks.
- Click to select the user’s Wi-Fi network. The Wi-Fi name automatically populates in the SSID field.
- In Security Key, enter the password of the Wi-Fi network. This is case-sensitive.
- Хадгалах товчийг дарна уу.
- Once the video device’s status LED turns solid green, begin enrollment. If the video device status LED does not turn solid green, double-check the Wi-Fi name and password and try again or, for alternative connection options, see Connect the video device to an internet network.
User interface version two
- Скан дарна уу.
- Click to select the desired network. The Wi-Fi name automatically populates in the SSID field.
- In the Password field, enter the password of the Wi-Fi network. This is case-sensitive.
- Илгээх дээр дарна уу.
- Once the video device’s status LED turns solid green, begin enrollment. If the video device status LED does not turn solid green, double-check the Wi-Fi name and password and try again, or for alternative connection options, see Connect the video device to an internet network.
Enroll the camera to the customer account:
Once the video camera is connected to the Wi-Fi, follow the on-screen associate the camera to the customer’s account using the Customer app Video Installation Wizard, Customer Webсайт (www.alarm.com/addcamera), or MobileTech app. For more information about the Video Installation Wizard, see
- https://answers.alarm.com-Partner-Installation-and-Troubleshooting-Video-Devices-General-Video-Information-AP-mode-I…
- Updated: Thu, 31 Oct 2024 13:52:28 GMT
Түгээмэл асуултууд
Асуулт: Би бүтээгдэхүүнтэй ямар нэгэн Wi-Fi адаптер ашиглаж болох уу?
A: No, the product requires a supported Wi-Fi adapter with specific chipsets such as Realtek’s RTL8811AU, RTL8811CU, or RTL8812BU.
Асуулт: Би төхөөрөмжийн нэрийг хэрхэн өөрчлөх вэ?
A: You can change the device name through the settings of the Mconnect Control app on your mobile device.
Асуулт: Хэрэв бүтээгдэхүүн Wi-Fi сүлжээнд холбогдоогүй бол би яах ёстой вэ?
A: Ensure that the Wi-Fi adapter is properly installed, and both your mobile device and the product are connected to the same Wi-Fi network. You can also try restarting both devices.
Баримт бичиг / нөөц
 |
emm Labs WiFi холболтыг хяналтын програмтай AP горимыг ашиглана [pdf] Хэрэглэгчийн гарын авлага Удирдлагын програмтай AP горимыг ашиглан WiFi холболт, Хяналтын програмтай AP горимыг ашиглах, Хяналтын програмтай горим, Хяналтын програмыг ашиглах |