S300 eufyCam Quick Start Guide

At a Glance

The S300 eufyCam features the following components:

• 1. SYNC Button: A button for synchronization.
• 2. Camera Lens: The primary lens for capturing video.
• 3. Photosensitive Sensor: Detects ambient light levels.
• 4. Spotlight: An integrated light for illumination.
• 5. LED Indicator: Shows the status of the device.
• 6. Microphone: Captures audio.
• 7. Motion Sensor: Detects movement.
• 8. Mounting Hole: For attaching the camera to a mount.
• 9. USB-C Charging Port: For powering the device.
• 10. Speaker: Outputs audio.

Diagram Description: An illustration shows the front and side view of the S300 eufyCam, with numbered callouts pointing to each component listed above.

Adding S300 eufyCam

To add your S300 eufyCam to your eufy Security system:

1. Open the eufy Security app.
2. Follow the on-screen instructions to add your eufy Security devices.
3. Choose 'Add Device'.
4. Select 'S300 eufyCam' to add it to your system.

Diagram Description: An illustration shows a smartphone displaying the eufy Security app interface, with an icon indicating device connection, next to the S300 eufyCam and its HomeBase.

Charging S300 eufyCam

You can charge the S300 eufyCam using two options:

Option 1: Connect the camera to USB Port 1 (e.g., HomeBase) using the provided USB cable.

Option 2: Connect the camera to a 5V USB Charger using the provided USB cable.

Diagram Description: Two diagrams illustrate the charging process. Option 1 shows the camera connected to a base unit via USB. Option 2 shows the camera connected to a 5V USB charger via USB.

LED Indicator Status

Charging Time: 8 Hours

Mounting the Camera

Select a Location

Choose a location that provides the desired view. It is recommended to mount the camera 7-10 ft (2-3 m) above the ground.

Diagram Description: An illustration shows a camera mounted on an exterior wall. It depicts the camera's field of view and motion detection zone, indicating a recommended mounting height of 7-10 ft (2-3 m) and a detection range of up to 26 ft (8 m).

Mount the Camera

1. Turn the knob of the mounting bracket counterclockwise to loosen and disassemble it.
2. Drill holes using a 15/64 inch (6 mm) drill bit. Insert wall anchors into the holes, which are necessary for hard materials like concrete, brick, or stucco.
3. Firmly screw the knob of the mounting bracket into the mounting hole.
4. Hold and screw the camera to the mounting bracket. Rotate the camera to adjust the view. Use the live stream in the eufy Security app to check the view.

Diagram Description: Four illustrations show the mounting process: disassembling the bracket, drilling holes and inserting anchors, attaching the bracket, and finally attaching the camera and adjusting its angle.

Safety Information

General Usage:

• Do not use the device in environments with temperatures that are too high or too low.
• Never expose the device to strong sunshine or excessively wet environments.
• The suitable temperature range for the T8161 and its accessories is -20°C to 50°C (Charging temperature is 0°C to 45°C).
• It is recommended to operate the device in an environment with a temperature between 5°C and 25°C.
• When powered, place the device in an environment with normal room temperature and good ventilation.

Warnings:

• Replacing a battery with an incorrect type may disable safeguards.
• Disposing of a battery in fire or a hot oven, or mechanically crushing or cutting a battery, can result in an explosion.
• Storing a battery in an environment with extremely high temperatures may lead to an explosion or the leakage of flammable liquid or gas.
• Exposing a battery to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas.

CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS. ⚠️

Notices

Compliance Information

This product complies with the radio interference requirements of the European Community and the United Kingdom.

Declaration of Conformity: Anker Innovations Limited declares that this device complies with the essential requirements and other relevant provisions of Directive 2014/53/EU and the Radio Equipment Regulations 2017 (SI 2017/1206). For the full declaration, visit: https://uk.eufylife.com.

RF Exposure Information:

The Maximum Permissible Exposure (MPE) level has been calculated based on a distance of 20 cm between the device and the human body. To maintain compliance with RF exposure requirements, ensure a distance of at least 20 cm is maintained between the device and the user.

Importer Information:

For EU matters: Anker Innovations Deutschland GmbH, Georg-Muche-Strasse 3, 80807 Munich, Germany

For UK matters: Anker Technology (UK) Limited, GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom

Recycling Information:

Your product is designed and manufactured with high-quality materials and components that can be recycled and reused. ♻️

This symbol indicates that the product must not be discarded as household waste. It should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling help protect natural resources, human health, and the environment. For more information, contact your local municipality, disposal service, or the shop where you purchased the product.

Troubleshooting

For troubleshooting, check the 'Help' section in the eufy Security app. For LED indicator status, refer to the app's status page.

Contact & Support

12-month limited warranty

United States: +1 (800) 988 7973

United Kingdom: +44 (0) 1604 936 200

Germany: +49 (0) 69 9579 7960

Email: support@eufylife.com

Social Media: @EufyOfficial (Facebook, X, Instagram)

Manufacturer: Anker Innovations Limited, Unit 56, 8th Floor, Tower 2, Admiralty Centre, 18 Harcourt Road, Hong Kong