Redragon Star Blade Pro - User Guide and Warranty
Introduction
Thank you for choosing a Redragon product. Please read the following warranty rules carefully to ensure better customer service.
Warranty Information
Within 10 months of the purchase date, repair is guaranteed for failures due to electrical insufficiencies. Other damages, such as disassembly, hard impacts, submersion into liquid, plugging into incompatible power sources, leakage, and damage caused by natural disasters like fire, flood, or earthquake are not covered.
Consumable parts (such as foot pads) and spare parts replacement are not included in this warranty.
Product Information
Model: 120-100
Deep-sear
O.S. Support
This section details support for different operating systems and connection methods.
How to Connect the Keyboard with Multi-ple Devices (Wired Connection)
- 2.4G OFF/BT switch on "OFF".
- Connect the keyboard to your computer with a USB cable.
- The computer will recognize and configure the keyboard automatically.
2.4G Wireless Connection
- 2.4G/BT switch on "2.4G". The LED [indicator light] flashes in Yellow. Plug the USB receiver into the computer USB port. After pairing, the LED will turn steady Yellow.
Bluetooth Connection
- 2.4G/BT switch on "BT".
Restore Factory Settings
Power save mode & How to recharge
On wireless connection mode, the keyboard will enter power save mode automatically after 5 minutes of inactivity. To wake it up, press any key. If the keyboard is low on battery, the LED will flash when typing. Connect the charging cable to charge the keyboard. The LED will be steady Red while charging and turn off when fully charged.
Power button indicator and LED
Battery power indicator and LED status:
- [Battery low]: Battery power indicator flashes Red.
- [Charging]: Battery power indicator is steady Red.
- [Fully Charged]: Battery power indicator turns off.
BATTERY SAFETY GUIDELINES
DO NOT use this product if the battery shows signs of damage, including but not limited to tearing, deformation, leakage, or the smell of electrolytic material.
FAQ
Q: My keyboard doesn't respond.
A: Check if the keyboard is properly connected. If using wireless mode, ensure the battery is charged and the 2.4G/BT switch is in the correct position. Try reconnecting the USB receiver or Bluetooth.
Q: How to reset the keyboard?
A: To reset the keyboard to factory settings, press and hold the [ESC] key and the [~] key simultaneously for 3 seconds.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These devices are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Product Features
Backlighting:
- Press [FN] + [Scroll Lock] to cycle through backlight modes (e.g., Static, Breathing, Rainbow, Wave, Reactive).
- Press [FN] + [Home] to adjust backlight brightness (5 levels).
- Press [FN] + [End] to adjust backlight color (Red, Green, Blue, Yellow, Purple, Cyan, White).
- Press [FN] + [Page Up] to adjust backlight speed (slow, medium, fast).
- Press [FN] + [Page Down] to adjust backlight direction (left, right, up, down).
- Press [FN] + [Insert] to turn backlight on/off.
- Press [FN] + [Delete] to enter custom backlight mode.
- Press [FN] + [Arrow Keys] to adjust backlight effects.
Other Functions:
- [Win Lock]: Press [FN] + [Win] to lock/unlock the Windows key.
- [Multimedia Keys]: Access media controls via FN key combinations (e.g., Play/Pause, Volume Up/Down, Mute).
Troubleshooting
Keyboard not working: Ensure the keyboard is properly connected. Try a different USB port. If using wireless, check battery and connection mode.
Backlight issues: Ensure the backlight is enabled and brightness is turned up. Reset the keyboard if necessary.
Product Name
REDRAGON STAR BLADE PRO
7227
