FXLuminaire Designer/Standard Wall Light Installation and Safety Guide

Installation Instructions

Follow these steps for proper installation:

Step 1: Conduit Preparation

Use the provided conduit. Trim its length if necessary.

Step 2: Sleeve Installation

Install the conduit sleeve into the wall during construction. Run the fixture wiring through the sleeve. (Note: Coupling is for VO fixture only).

Step 3: Voltage Check

Use a voltmeter to ensure the voltage at the fixture is between 11V and 15V.

Step 4: Wiring Connection

Connect the wiring using a waterproof connector.

Step 5: Faceplate Installation

Press the faceplate into the sleeve. Level and orient the fixture as desired.

For concrete ground-mount options, use the appropriate construction housing.

Circuiting Guidelines

Proper wire gauge selection is crucial to minimize voltage drop. The following table provides recommendations based on distance and wattage:

Distance	Voltage	Wire Gauge (AWG/mm²)	Max Wattage
0-40' (0-13 m)	15V	12 AWG (4.0 mm²)	160W
		10 AWG (6.0 mm²)	180W
40'-80' (13-25 m)	15V	12 AWG (4.0 mm²)	120W
		10 AWG (6.0 mm²)	140W
80'-120' (25-40 m)	15V	12 AWG (4.0 mm²)	100W
		10 AWG (6.0 mm²)	120W
120'-160' (37-50 m)	15V	12 AWG (4.0 mm²)	60W
		10 AWG (6.0 mm²)	100W

Transformer Guidelines

Single Transformer

When using a single transformer, center it relative to the total wattage load. Minimize all cable runs to reduce voltage drop.

Multiple Transformers

When using multiple transformers, spread the load evenly across all units. Install transformers as close to the fixtures as possible to avoid voltage drop.

Safety Precautions

WARNING: To reduce the risk of FIRE OR INJURY TO PERSON:

Turn off/unplug and allow to cool before replacing lamp.
Lamp gets HOT quickly. Contact only the switch/plug when turning on.
Do not touch hot lens, guard, or enclosure.
Keep lamp away from materials that may burn.
Do not touch the lamp at any time. Use a soft cloth. Oil from skin may damage the lamp.
Do not operate the luminaire fitting with a missing or damaged shield.

WARNING: Risk of Electric Shock

May be installed less than 5' (1.5 m) from a pool, spa, or fountain when used with a UL 379 listed transformer.
A luminaire shall not use tungsten halogen lamps unless the luminaire is marked for such lamps.
Supply connection and electrical components are located above ground level, except for secondary cord that is suitable for wet locations.

Low Voltage Cable Requirements

Be protected by routing in close proximity to the luminaire or fitting, or next to a building structure such as a house or deck.
Not be buried except for a maximum 6" (152 mm) in order to connect to the main low voltage cable.
Have the length cut off so that it is connected to a connector within 6" (152 mm) from a building structure, a luminaire, or fitting.

Certifications

CE Certified: PO and MO Only
UL Listed: PO, MO and CG Only
ETL Listed: VO Only

General Information

This product contains a light source of energy efficiency class G.

For more information and support, visit: fxl.com/support

	FXLuminaire Designer/Standard Wall Light Installation Guide (PO, MO, VO, CG) Comprehensive installation, circuiting, and safety guide for FXLuminaire Designer/Standard wall lights, including PO, MO, VO, and CG models. Provides step-by-step instructions, wiring guidelines, and essential safety precautions.
	FXLuminaire BQ Landscape Lighting Installation and Safety Guide Comprehensive installation instructions, circuiting guidelines, and safety warnings for the FXLuminaire BQ designer specialty light.
	FXLuminaire Designer/Standard Down Light Installation and Safety Guide This guide provides installation instructions, circuiting guidelines, and essential safety information for the FXLuminaire Designer/Standard Down Light series, including VE, LE, VL, and LS models. Learn about transformer usage, low voltage cable requirements, and important precautions for safe operation.
	FXLuminaire MO Recessed Wall Light: Specifications, Ordering, and Photometrics Detailed specifications, ordering information, and photometric data for the FXLuminaire MO Recessed Wall Light. Features include die-cast brass construction, Lumileds LEDs, Luxor Technology compatibility, and various finishes. Ideal for landscape and architectural lighting.
	FXLuminaire VK LED Wall Light: Specifications, Features, and Ordering Guide Detailed specifications, features, materials, and ordering information for the FXLuminaire VK LED Wall Light, a modern, sleek, and durable recessed luminaire designed for landscape and architectural applications. Includes technical data, photometrics, and finish options.
	FXLuminaire Wall Light Installation and Safety Guide (CP, LM, UN, PD) A comprehensive guide for FXLuminaire CP, LM, UN, and PD wall lights, detailing installation steps, crucial safety warnings, technical specifications, and compliance information.
	FXLuminaire ST-UV Transformer: 30W Universal Voltage Step-Down Transformer Discover the FXLuminaire ST-UV Transformer, a 30W universal voltage step-down transformer for landscape and architectural lighting. Key features include 85-305 VAC input, 12 VAC output, compact design, and screw terminal mounting.
	FXLuminaire MO LED Wall Lights: Specifications, Ordering, and Photometrics Comprehensive product details for FXLuminaire MO LED wall lights, covering specifications, ordering information, available finishes, and photometric performance data for various configurations including 1LED, 3LED, and ZDC options with different faceplates.

FXLuminaire Designer/Standard Wall Light