Curved Digital Atomic Wall Clock with Moon Phase

Power Up

To power up your clock and outdoor sensor:

1. Insert 2-AA batteries into your Outdoor Sensor (TX141-Bv3).
2. Insert 3-AA batteries into your Atomic Clock (BBB86111v3).
3. Enter the Settings Menu to adjust your time and date.
4. Once the sensor is reading to your clock, place the sensor outside in a shaded location.

View our sensor mounting video here: bit.ly/th_sensor_mounting

Battery Installation Diagrams:

• Outdoor Sensor (TX141-Bv3) requires 2x AA batteries, noting correct polarity (+/-).
• Atomic Clock (BBB86111v3) requires 3x AA batteries, noting correct polarity (+/-).

Atomic Time

The clock will automatically search for the Atomic Time Signal at power up and at UTC 7:00, 8:00, 9:00, 10:00, and 11:00.

The Atomic Time Signal Icon ? will flash while searching and be solid when it has connected.

To manually start or stop a search for the WWVB time signal, press the SEARCH button from the normal time display.

For information about WWVB, visit: bit.ly/AtomicTime

Settings Menu

To enter the Settings Menu:

1. Hold the SET button.
2. Use the +/- buttons to adjust values.
3. Press SET to confirm values.
4. Press the SNOOZE button at any time to save and exit.

Settings Menu Order:

• Beep ON/OFF
• Atomic ON/OFF
• DST AUTOMATIC / DST ALWAYS OFF / DST ALWAYS ON (Change Spring/Fall) (Standard Time all year) (DST all year)
• Time Zone (Options: ATLANTIC, EASTERN, CENTRAL, MOUNTAIN, PACIFIC, ALASKA, HAWAII)
• Hour
• Minutes
• Year
• Month
• Date
• Temperature Fahrenheit/Celsius

Notes:

• If Atomic OFF is selected, the menu will skip DST and Time Zone settings and move straight to the Hour setting.
• Weekday sets automatically when Year, Month, and Date are set.

Custom Display

Press the MOON button to switch between Calendar or Moon Phase display. Your clock will stay on the selection.

Moon Phase

The moon phase is based on the Lunar Calendar and the year, month, and date settings.

Due to character limitations on the clock, Large and Small Waxing and Waning Phases will not state "Large" or "Small".

Phase / Clock Reads:

• NEW MOON
• WAXING CRES
• WAXING CRES
• FIRST QTR
• WAXING GIBB
• WAXING GIBB
• FULL MOON
• WANING GIBB
• WANING GIBB
• LAST QTR
• WANING CRES
• WANING CRES

Time Alarm

Set Alarm:

1. Hold the ALARM button to enter Alarm Settings.
2. Use the +/- buttons to adjust values.
3. Press the ALARM button to confirm and move to the next item.

Silence a sounding alarm: Press any button except SNOOZE to silence the alarm for 24 hours.

Activate/Deactivate Alarm:

• Press the ALARM button to activate or deactivate the alarm.
• The Alarm Icon ? will show when the alarm is active.

Snooze:

• When the alarm sounds, press the SNOOZE button to silence the alarm for 10 minutes. "Zz" will show.

Note: The alarm will sound with increasing frequency for two minutes, then shut off automatically if not silenced.

HI/LO Temperature Records

View: Press the + button to view Outdoor, then Indoor Temperature HI and LO Records with time and date stamps.

Reset: While viewing individual records, hold the - button to reset to current temperatures.

Temperature Trend Arrows:

Both the Indoor and Outdoor temperature have Trend Arrows to indicate temperature changes (2°F / 1°C) over the past one hour period.

• Temperature has risen over the past hour: ⬆️
• Temperature has been steady over the past hour: ➡️
• Temperature has fallen over the past hour: ⬇️

Search for Outdoor Temperature

If you are seeing NO or dashes for your outdoor readings, please try the following steps:

1. Hold the SEARCH button to search for your outdoor sensor. The Reception Indicator ? will begin to animate.
2. If after 3 minutes the sensor still isn't connected, bring the sensor inside next to the display and remove power from both the sensor and clock.
3. Press any button on the clock 20 times and leave the parts sit for a few moments with the power off.
4. Install a new set of alkaline batteries into the sensor, then into your clock.

For additional help visit: bit.ly/basic_restart

If your outdoor data is still not appearing after these steps, please contact support staff via the links below.

We're Here to Help

For additional support, contact the customer support team based in La Crosse, WI.

Phone: 1.608.782.1610

Online: bit.ly/contact_techsupport

Customer support team is available: Mon-Fri 8am-6pm CST.

Stay in Touch

Ask questions, watch setup videos, and provide feedback on social media outlets.

Follow La Crosse Technology on: [YouTube], [Twitter], [Facebook], and [Instagram].

Low Battery Indicator

• By the Time: replace clock batteries.
• By the Outdoor Temperature: replace sensor batteries.

Care + Maintenance

• Do not mix old and new batteries.
• Do not mix Alkaline, Lithium, standard, or rechargeable batteries.
• Always purchase the correct size and grade of battery most suitable for intended use.
• Clean the battery contacts and those of the device prior to battery installation.
• Ensure batteries have been installed with correct polarity (+/-).
• Remove batteries from equipment that will not be used for an extended period.
• Promptly remove expired batteries.

Specifications

Atomic Clock (BBB86118v3)

• Temperature Range: 32°F to 122°F (0°C to 50°C)
• Power Requirements: 3-AA, IEC, LR6 batteries (not included)
• Dimensions: 12.19" W x 1.59" D x 11.80" H (30.96 W x 4.04 D x 29.98 H cm)

Outdoor Sensor (TX141-Bv3)

• Temperature Range: -40°F to 140°F (-40°C to 60°C)
• Transmission Range: Over 330 ft. open air (100 meters) RF 433MHz
• Update Interval: About every 51 seconds
• Power: 2-AA, IEC, LR6 batteries (not included)
• Battery Life: Over 12 months
• Dimensions: 1.57" L x 0.79" W x 5.12" H (4.0cm L x 2.0cm W x 13.0 H cm)

Warranty Info

La Crosse Technology, Ltd. provides a 1-year limited time warranty (from date of purchase) on this product relating to manufacturing defects in materials & workmanship.

La Crosse Technology, Ltd,
2830 S. 26th St.
La Crosse, WI 54601

For Full Warranty Details, Visit: www.lacrossetechnology.com/pages/warranty

WARNING: This product can expose you to chemicals including styrene, which is known in the State of California to cause cancer. For more information, go to: www.P65Warnings.ca.gov

Compliance Statements

Canada Statement

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : 1) L'appareil ne doit pas produire de brouillage; 2) L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.

Caution! Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

All rights reserved. This manual may not be reproduced in any form, even in part, or duplicated or processed using electronic, mechanical or chemical process without the written permission of the publisher. This booklet may contain errors or misprints. The information it contains is regularly checked and corrections are included in subsequent editions. La Crosse Technology disclaims any responsibility for any technical error or printing error, or their consequences. All trademarks and patents are recognized.