DigitalMedia PUF 2.63.00
Product or Content Description
Included Firmware
| DigitalMedia™ Switcher Model Name | Description | Component | Firmware Version | Min. BL |
|---|---|---|---|---|
| DM-MD8x8 DM-MD8x8-RPS DM-MD16x16 DM-MD16x16-RPS |
8x8 or 16x16 DM switcher | Main application OOTBF RPS FP main application FP OOTBF |
4.102.352400069* 1.0.140* 1.1498.00021 2.002.0026 1.0.114 |
339 |
| DM-MD32x32 DM-MD32x32-RPS |
32x32 DM switcher | Main application OOTBF RPS FP main application FP OOTBF |
4.102.352400069* 1.0.140* 1.1498.00021 2.002.0026 1.0.114 |
339 |
| DM-MD6x1 | 6x1 DM switcher | Main application OOTBF |
4.102.245600045 1.0.77 |
339 |
| DM-MD6x4 DM-MD6x6 |
6x4 or 6x6 DM switcher | Main application OOTBF FP main application FP OOTBF |
4.102.291100011 1.0.77 1.2911.00086* 1.0.72 |
339 350* |
| DigitalMedia™ Endpoints Model Name | Description | Component | Firmware version | Min. BL |
|---|---|---|---|---|
| DM-TX-4KZ-202-C DM-TX-4KZ-302-C |
4K60 4:4:4 HDR dual HDMI or dual HDMI+DP 8G+ HDBaseT transmitter | Main application HDBT TX application |
1.3691.00041* 7.1.19* |
382* |
| DM-TX-4KZ-302-C | 4K60 4:4:4 HDR dual HDMI+DP 8G+ HDBaseT transmitter | DP RX application | 11.111.0* | |
| DM-TX-4K-202-C DM-TX-4K-302-C |
4K dual HDMI or dual HDMI+RGB 8G+ HDBaseT transmitter | Main application | 1.2911.00086* | 350 |
| DM-TX-4K-100-C-1G | 4K 8G+ HDBaseT 1G transmitter | Main application | 1.3209.00023 | 343 |
| DM-TX-200-C-2G | HDMI+RGB 8G+ HDBaseT 2G transmitter | Main application FPGA |
1.2911.00047 19 |
329 |
| DM-TX-201-C | HDMI+RGB 8G+ HDBaseT transmitter | Main application FPGA |
1.2911.00081* 48 |
350* |
| DM-TX-401-C | HDMI+DP+RGB 8G+ HDBaseT transmitter | Main application | 1.2911.00046 | 329 |
| DM-RMC-4KZ-100-C | 4K60 4:4:4 HDR 8G+ HDBaseT receiver | Main application HDBT RX application |
1.3691.00040* 7.1.19 |
382* |
| DM-RMC-4K-SCALER-C DM-RMC-4K-SCALER-C-DSP |
4K 8G+ HDBaseT advanced receiver | Main application Core DSP |
1.2911.00081* 5.5 3.30.1.169 |
350 |
| DM-RMC-4K-100-C | 4K or 2K 8G+ HDBaseT receiver | Main application | 1.2911.00046 | 329 |
| DM-RMC-100-C | 4K 8G+ HDBaseT 1G receiver | Main application | 1.3209.00023 | 343 |
| DM-RMC-4K-100-C-1G | 8G+ HDBaseT advanced receiver | Main application | 1.2911.00079 | 350 |
| DM-RMC-SCALER-C DM-RMC-200-C |
8G+ HDBaseT advanced receiver | Main application | 1.2911.00079 | 350 |
| DM-TX-201-S DM-TX-201-S2 |
HDMI+RGB 8G fiber transmitter | Main application FPGA |
1.2911.00027 64 |
322 |
| DM-TX-401-S DM-TX-401-S2 |
HDMI+DP+RGB 8G fiber transmitter | Main application | 1.2911.00033* | 329* |
| DM-RMC-200-S | 8G fiber advanced receiver | Main application | 1.2625.00028 | 268 |
| DM-RMC-SCALER-S | 8G fiber advanced receiver | Main application FPGA |
1.2456.00045 4 |
268 |
| DM-RMC-150-S | 8G fiber receiver | Main application | 1.2456.00045 | 268 |
| DM-RMC-100-S | Multi-format fiber transmitter | Main application FPGA |
1.2456.00045 23 |
268 |
| DM-TX-300N-F | HDMI fiber transmitter | Main application | 1.2456.00045 | 268 |
| DM-TX-100-F | Fiber receiver | Main application | 1.1498.00021 | 268 |
| DM-RMC-100-F | Multi-format CAT 3G transmitter | Main application FPGA |
1.2625.00028 7 |
268 |
| DM-TX-400-3G | Multi-format CAT 3G transmitter | Main application FPGA |
1.2625.00013 23 |
268 |
| DM-TX-300N | HDMI+RGB CAT standalone or 2G transmitter | Main application FPGA |
1.2625.00028 41 |
105 |
| DM-TX-200 DM-TX-200-2G |
HDMI CAT transmitter | Main application | 1.2456.00045 | 268 |
| DM-TX-100 | HDMI CAT 1G transmitter | Main application | 1.1498.00021 | 69 |
| DM-TX1-1G | CAT receiver | Main application | 1.1498.00021 | 268 |
| DM-RMC-100 | CAT 1G receiver | Main application | 1.1498.00021 | 69 |
| DM-RX1-1G | CAT repeater | Main application | 1.1498.00021 | 69 |
| DM-DR |
| DigitalMedia™ Cards Model Name | Description | Component | Firmware version | Min. BL |
|---|---|---|---|---|
| DMC-4KZ-HD DMC-4KZ-HD-DSP |
4K60 4:4:4 HDR HDMI input card | Main application DSP |
1.3691.00040* 5.5.0 |
382* |
| DMC-4K-HD DMC-4K-HD-DSP |
4K HDMI input card | Main application DSP |
1.2911.00082* 5.5.0 |
350 |
| DMC-HD DMC-HD-DSP |
HDMI input card | Main application FPGA DSP |
1.2911.00082* 56 3.4.5 |
329 |
| DMC-4K-HDO | 4K HDMI advanced output card | Main application Core |
1.2911.00073 1.114.1.188 |
350 |
| DMC-4KZ-C DMC-4KZ-C-DSP |
4K60 4:4:4 HDR 8G+ HDBaseT input card | Main application HDBT RX application DSP |
1.3691.00040* 7.1.19* 5.5.0* |
382* |
| DMC-4K-C DMC-4K-C-DSP |
4K 8G+ HDBaseT input card | Main application DSP |
1.2911.00084* 5.5.0 |
350 |
| DMC-C DMC-C-DSP |
8G+ HDBaseT input card | Main application DSP |
1.2911.00084* 5 3.4.5 |
350* |
| DMC-4KZ-CO-HD | 4K60 4:4:4 HDR 8G+ HDBaseT output card | Main application HDBT TX application |
1.3691.00040* 7.1.19 |
382* |
| DMC-4K-CO-HD | 4K 8G+ HDBaseT output card | Main application | 1.2911.00076 | 350 |
| DMC-CO-HD | 8G+ HDBaseT output card | Main application FPGA |
1.2625.00031 40 |
268 |
| DMC-DVI | DVI input card | Main application FPGA |
1.2625.00013 16 |
268 |
| DMC-VGA | VGA input card | Main application FPGA |
1.2911.00017 11 |
322 |
| DMC-SDI | SDI input card | Main application FPGA |
1.2911.00003 40 |
322 |
| DMC-S DMC-S2 DMC-S-DSP DMC-S2-DSP |
8G fiber input card | Main application FPGA DSP |
1.2911.00057 3 3.4.5 |
329 |
| DMC-SO-HD DMC-S2O-HD |
8G fiber output card | Main application FPGA1 FPGA2 |
1.2911.00020 14 15 |
322 |
| DMC-STR | Streaming input card | Main application Codec OS application |
1.2911.00043 1.0002.00033* |
329 |
| DMC-STRO | Streaming output card | Main application Codec OS application Scaler |
1.2911.00043 1.001.0000 3 |
329 |
| DMC-VID-BNC DMC-VID-RCA-A DMC-VID-RCA-D |
Analog video input card | Main application | 1.1592.00036 | 69 |
| DMC-VID4 | Security camera composite input card | Main application | 1.1498.00021 | 69 |
| DMC-F DMC-F-DSP |
Fiber input card | Main application FPGA DSP |
1.2456.00045 58 3.4.5 |
69 |
| DMC-FO-HD | Fiber output card | Main application | 1.2456.00031 | 69 |
| DMC-CAT DMC-CAT-DSP |
CAT input card | Main application FPGA DSP |
1.1498.00021 60 3.4.5 |
69 |
| DMC-CATO-HD | CAT output card | Main application FPGA |
1.1498.00021 39 |
69 |
* Denotes new or updated firmware compared to PUF 2.62.04.
Notes and Recommendations
DigitalMedia PUF 2.63.00 is maintenance bug fix release. PUF 2.63.00 is the first public release to include firmware for the DMC-4KZ-C, DMC-4KZ-C-DSP, DM-TX-4KZ-302-C and DM-TX-4KZ-202-C.
Important Note:
Please be aware of the following before upgrading/downgrading:
- Special steps must be taken to downgrade DM-MD32x32 CPU cards from DM PUF 2.50 or later to PUF 2.48 or prior. Please see Crestron OLH ID 1285 for details. Other DM products are unaffected.
- Several DM cards have larger firmware files and can take longer to upgrade than other DM products:
a. DM-STR: Up to 30 minutes per group of 4 cards.
b. DMC-STRO: Up to 17 minutes per group of 4 cards. - To minimize upgrade time, it is recommended to stop active DMC-STR/STRO streams prior to performing a PUF upgrade.
Recommended Streaming Settings
When pairing the DMC-STR with the DMC-STRO, it is recommended to stream via RTP with initiation by receiver. Previous bandwidth and format restrictions have been removed. Use of TS encapsulation at the DMC-STRO is not recommended due to compatibility issues with many streaming decoders on the market.
With the release of PUF 2.51, the default ports used by the DMC-STRO have changed. Port numbers used in existing installations will not change on firmware upgrade, but they will change on card or system restore. Also, new port numbers applied to systems upgrading from pre-PUF 2.51 code will not be applied until after card restore. Please see OLH 5552 for details.
If the DMC-STR is unable to connect to a third-party encoder (e.g., an IP Camera), re-attempt to connect by adding "?rtsp_tcp=yes" at the end of the URL (without quotations).
System Requirements and Dependencies
| Item | Version |
|---|---|
| Device Database | 94.00.001.00 |
| Crestron Database | 64.05.001.00 |
| SIMPL Windows | 4.08.15.02 |
| Crestron Toolbox | 3.01.481.00 |
Current Version
2.63.00
File name: digitalmedia_2.63.00.puf
Date: 2018-06-08
New Features
- Added support for 4K60 4:4:4 HDR input cards and endpoints. Following devices are now supported:
- DMC-4KZ-C
- DMC-4KZ-C-DSP
- DM-TX-4KZ-302-C
- DM-TX-4KZ-202-C
Issues Fixed
- DM-RMC-4KZ-100-C doesn't work with HD-WP-4K-401-C.
- Fixed issue where DM-TX-401-S or DM-TX-401-S2 may sporadically fail to upgrade the firmware.
- A Remote Code Execution vulnerability (Similar to CVE-2018-11229 and CVE-2018-11228) has been addressed in this release of firmware. Crestron recommends updating firmware to prevent this vulnerability from being exploited. For more information see Crestron OLH Answer ID 5471.
Known Issues
- When NVIDIA Quadro P2000 connected as DP input source, DM-TX-4KZ-302-C may sporadically fail to output video after DM-TX-4KZ-302-C power cycles.
- TT-100 "Connect It" indicators don't work when connected to USB HID port of the DM-TX-4KZ-302/202-C, instead use COMPUTER port on the TX if necessary.
- DM-TX-4KZ-302/202-C may report incorrect input audio sampling frequency for non PCM audio formats.
- Audio_Format_fb, Audio_Channel_fb and Audio_Sampling_Freq_fb joins don't work for DMCI-DMC-4KZ-C/-DSP and DMCI-DMC-4KZ-HD/-DSP symbols.
- When switching upstream, 4K/4KZ outputs may have double audio lock with certain LG/Samsung Blu-Ray players.
- When HDR source is routed to DMC-4K-HDO output card, instead of no video it may output bad video depending on I/O signal video resolution. DMC-4K-HDO output card doesn't support HDR.
- 4K/4KZ DSP input cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio.
- DMC-4KZ-HD(-DSP) input card setup with DM default 4k 60Hz 2CH/HBR EDID may produce unstable video when connected to certain streaming or Blu-ray players.
- Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures. Instead assign input EDIDs in batches; 16 inputs at once.
- The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.
- Apple keyboard does not connect reliably to RMCs.
- All TXs (except TX-401-XX): HDMI audio unreliable with 480i video. All other resolutions are ok.
- On streaming cards, support for elapsed seconds, bitrate and initiator feedbacks have been removed to work around Toolbox stability issues.
- Streaming unsupported audio formats (e.g., G.711) can cause the DMC-STR to lock up. Use AAC audio.
- Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover.
Version History
2.62.04
Issues Fixed
- Fixed issue where 4KZ cards may sporadically lose TSID. There is no user facing functionality affected by loss of TSID.
- DM-RMC-4KZ-100-C unable to pass video to certain Samsung xxNUxxxx series displays.
Known Issues
- When switching upstream, 4K/4KZ outputs may have double audio lock with certain LG/Samsung Blu-Ray players.
- When HDR source is routed to DMC-4K-HDO output card, instead of no video it may output bad video depending on I/O signal video resolution. DMC-4K-HDO output card doesn't support HDR.
- DM-RMC-4KZ-100-C doesn't work with HD-WP-4K-401-C.
- 4K/4KZ DSP input cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio.
- DMC-4KZ-HD(-DSP) input card setup with DM default 4k 60Hz 2CH/HBR EDID may produce unstable video when connected to certain streaming or Blu-ray players.
- Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures. Instead assign input EDIDs in batches; 16 inputs at once.
- The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.
- Apple keyboard does not connect reliably to RMCs.
- All TXs (except TX-401-XX): HDMI audio unreliable with 480i video. All other resolutions are ok.
- On streaming cards, support for elapsed seconds, bitrate and initiator feedbacks have been removed to work around Toolbox stability issues.
- Streaming unsupported audio formats (e.g., G.711) can cause the DMC-STR to lock up. Use AAC audio.
- Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover.
Click here for the digitalmedia_2.62.04.puf detailed release notes.
2.62.00
New Features
- Added support for 4K60 4:4:4 HDR I/O cards and endpoint. Following devices are now supported:
- DMC-4KZ-HD(-DSP)
- DMC-4KZ-CO-HD
- DM-RMC-4KZ-100-C
- Added support for 1080p25/30 resolution for DM-RMC-SCALER/200-C.
- Added HDCP Transmitter mode functionality for the HDMI/DM output of the DM-TX-4K-302/202-C and DM-RMC-4K-SCALER-C endpoints. The feature is only available programmatically.
Issues Fixed
- Fixed issue with 4K cards/endpoints and Barco Balder Cinemascope where incorrectly parsed EDID capabilities will output bad video.
Known Issues
- When switching upstream, 4K/4KZ outputs may have double audio lock with certain LG/Samsung Blu-Ray players.
- When HDR source is routed to DMC-4K-HDO output card, instead of no video it may output bad video depending on I/O signal video resolution. DMC-4K-HDO output card doesn't support HDR.
- DM-RMC-4KZ-100-C doesn't work with HD-WP-4K-401-C.
- 4K/4KZ DSP input cards do not down-mix DTS:X or Dolby Atmos audio to PCM 2ch audio.
- DMC-4KZ-HD(-DSP) input card setup with DM default 4k 60Hz 2CH/HBR EDID may produce unstable video when connected to certain streaming or Blu-ray players.
- Assigning Global EDID via DM Tool to fully populated DM-MD32x32 chassis may report false failures. Instead assign input EDIDs in batches; 16 inputs at once.
- The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.
- Apple keyboard does not connect reliably to RMCs.
- All TXs (except TX-401-XX): HDMI audio unreliable with 480i video. All other resolutions are ok.
- On streaming cards, support for elapsed seconds, bitrate and initiator feedbacks have been removed to work around Toolbox stability issues.
- Streaming unsupported audio formats (e.g., G.711) can cause the DMC-STR to lock up. Use AAC audio.
- Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover.
Click here for the digitalmedia_2.62.00.puf detailed release notes.
2.61.00
New Features
- DMC-4K-HDO now supports scaling, arbitrary video wall configuration and bezel compensation.
- DM-MD6x4/6x6 now supports programmatic control of the DM-RMC-4K-100-C-1G.
- Added support for applying custom EDID to the input of all the scaler RMCs.
- Added programmatic control to change scaler state for all the scaler RMCs.
- Added programmatic control to enable/disable analog audio output for all applicable RMCs.
- All scaling outputs now support freeze frame switching. 2K scaling products will still have black frame when switching between inputs with different resolutions.
Issues Fixed
- DMC-4K-HDO will report incorrect refresh rate on the output.
- Several DMC-4K-HDO stability issues.
- Fixed issue where DMC-4K-HD-HDCP2 will not pass video from certain 4K HDCP 2 sources.
- Fixed issue where DM-RMC-4K-SCALER-C has color fringe on certain text.
- Added ability to detect input source sync for DM-TX-4K-302/202-C without having to switch to that input.
- Fixed issue where DM-RMC-4K-100-C-1G does not get the DM link after DM-TX-200-C-2G power cycles.
- Fixed color space issue when passing YCbCr 422 source through DM-TX-201-C.
- DMC-SDI input card passes 1080p59.94 resolution.
- Fixed issue where certain HDBaseT projectors were uncommunicative in standby.
- Scaling outputs will release HDCP if input content is non-HDCP and connected sink does not support HDCP.
- Fixed issue where DM-RMC-200/SCALER/100-C endpoints may become unresponsive with excessive serial (RS-232) join traffic for extended time period.
Known Issues
- The DMC-STR may report a resolution of 0x0@0 when streaming from certain third-party IP cameras.
- Apple keyboard does not connect reliably to RMCs.
- All TXs (except TX-401-XX): HDMI audio unreliable with 480i video. All other resolutions are ok.
- On streaming cards, support for elapsed seconds, bitrate and initiator feedbacks have been removed to work around Toolbox stability issues.
- Streaming unsupported audio formats (e.g., G.711) can cause the DMC-STR to lock up. Use AAC audio.
- Network problems can sometimes cause the DMC-STR to stop decoding a stream. Stop and restart the stream to recover.
Click here for the digitalmedia_2.61.00.puf detailed release notes.
Licensing and Copyright Information
Certain Crestron products contain open source software. For specific information, please visit www.crestron.com/opensource
* Denotes new or updated firmware compared to PUF 2.62.04.
