EKET Cabinet Assembly Instructions
Important Safety Information
⚠️ WARNING: Serious or fatal crushing injuries can occur from furniture tip-over.
To prevent this furniture from tipping over, it must be permanently fixed to the wall using the wall attachment fittings included in the packaging. If the product is to be hanged on the wall, it must be done with the designated suspension rail (sold separately at IKEA). Assess the wall to ensure that it will withstand the weight. As wall materials vary, screws for wall fixation are not included. For advice on suitable screw systems for your wall, contact your local specialised dealer. Wall fixing/hanging must be carried out by a qualified person, since wrong fixation may cause injury or damage.
The original document provides this warning in multiple languages.
Parts Included
The package contains the following components:
- 4x Connector pieces (e.g., cam lock connectors)
- 4x Plastic dowels
- 3x Screws (for initial assembly)
- 1x Washer
- 2x Round caps
- 2x Circular brackets
- 2x Hinge mechanisms
- 2x Knobs/Handles
- 1x Drawer slide component (Part A)
- 1x Drawer slide component (Part B)
- 2x Drawer slide components (Part C)
- 1x Drawer slide component (Part D)
- 2x Small mounting brackets
- 1x Instruction booklet
Note: Wall fixing screws are not included as they depend on your wall type. A drill bit of Ø 8 mm (5/16") is indicated for some installation steps.
Assembly Guide
Step 1
Lay out all components. The diagram shows a drill bit of Ø 8 mm (5/16") and a screwdriver, spirit level, and drill as necessary tools.
Step 2
Assemble the base or side panels. This involves inserting a screw and a specific fitting, which locks into place with an audible 'click!'.
Step 3
Connect side panels to the base/top using dowels and screws. Three screws are used to secure one connection point.
Step 4
Attach another panel to the partially assembled unit.
Step 5
Slide the back panel into the grooves on the side panels. An 'X' symbol indicates an incorrect method of insertion.
Step 6
Attach the remaining side panel to the unit.
Step 7
Fully insert the back panel into its grooves. A close-up view shows how the back panel is secured.
Step 8
Attach mounting brackets to the back of the unit using screws. Four brackets are shown being attached.
Step 9
The diagram shows the assembled cabinet standing on its legs. An alternative configuration (without legs) is also implied. The EKET instruction booklet is shown.
Step 10
Attach hinge mechanisms to the side panels of the cabinet. Two mechanisms are shown being attached to one side.
Step 11
Secure the cabinet to a wall or another unit. This involves drilling holes (Ø 8 mm) and using fittings. Two fittings are shown.
Step 12
Attach adjustable feet or knobs to the bottom of the cabinet. Two such fittings are shown being screwed into place.
Step 13
Further secure the unit, possibly to a wall or another unit, using screws. Two screws are shown being inserted.
Step 14
Attach the door hinge components to the cabinet side panel. Two sets of components are shown.
Step 15
Attach the other part of the door hinge mechanism to the cabinet side panel. Two fittings are shown being attached.
Step 16
Attach the hinges to the door itself. One hinge is shown being attached with a screw and washer.
Step 17
Insert shelf supports into the pre-drilled holes inside the cabinet.
Step 18
Mount the door onto the cabinet by connecting the hinges. A close-up shows the hinge mechanism being secured to the door and the cabinet.
Step 19
Attach the door handle or knob to the door. One handle is shown being attached.
Step 20
Complete the door attachment. The diagram shows the door being clicked into its final position, indicating a secure hinge connection.
Step 21
Adjust the door for proper alignment. Arrows indicate the direction of adjustment.
Step 22
The final image shows the completed EKET cabinet. The instruction booklet is also displayed, suggesting a review of the assembly process.
