Speediance Smart Handles Product Manual
Safety Precautions
1. When charging the appliance, it is recommended to use an output of 5V/2A.
2. Before charging, check the socket area for lint, water, or other foreign objects. Clean the area thoroughly before inserting to prevent fire, electric shock, or short circuits.
3. During charging, avoid high-temperature or direct sunlight areas. Promptly remove the charger after charging is complete to prevent overcharging and potential accidents.
4. Do not charge the product for extended periods without supervision. The maximum charging time should not exceed 12 hours. If left unused for a long time, charge it to full capacity at least once every six months.
5. Charge the product in an environment between 5°C and 35°C. Store the product between -20°C and +45°C.
6. If any abnormal occurrences (unusual odors or sounds) happen during charging or usage, immediately cut off power and stop usage.
7. Do not press the button violently. If the smart handles or adjustment system malfunctions, stop using it and contact Speediance Aftersales immediately.
8. Any attempt to disassemble, modify, or damage electronic components (like circuit boards) is strictly prohibited. All repairs and maintenance must be conducted by experts. If the power cord is damaged, it must be replaced through official channels to prevent hazards.
Basic Information
The Smart Handles are a fitness accessory designed for use with Speediance equipment.
Diagram: Smart Handle Components
The diagram shows a Smart Handle suspended by a strap attached to a square ring. Key components labeled are:
- Square Ring: Connects the strap to the handle.
- Strap: Used for suspension or attachment.
- Charging Port: Located on the side of the handle for charging.
- Button: A circular button on the side of the handle, also featuring an indicator light and the Speediance logo.
Product Specifications
| Product Name | Smart Handles |
|---|---|
| Product Dimensions | 14.5*3.2*5cm |
| Bluetooth Parameter | Bluetooth 5.0 |
| Battery Parameter | 3.7V 480mAh |
Indicator Light Status
The indicator light on the button provides status information:
| Condition of Device | Indicator's Light |
|---|---|
| Normal Battery | White Light |
| Low Battery | Red Flashing Light |
| Disconnected | Flashing Light |
| Charging | Orange Light (not fully charged) / Blue Light (fully charged) |
How to Connect
To connect the Smart Handles:
- Press the button on the handle.
- Insert the square ring into the ball connector.
To disconnect:
- Press the button on the handle.
- Detach the square ring from the ball connector.
Awake Your Handles
To turn on your Smart Handles, press the button.
Bluetooth Connection/Disconnection
When the indicator light flashes, the Bluetooth is disconnected. You can search for the device on a Speediance machine or via the companion App.
How to Use
Single click on the button to pause or start a workout.
Sleeping Mode
The Bluetooth connection automatically disconnects after 120 seconds of no response.
How to Charge
A red flashing light indicates that the device needs charging. Charge the Smart Handles using the included USB-A to C cable.
Recommendation: 5V=2A power input is recommended.
Warning: Please do not use a multi-functional cable to charge the device to prevent potential damage.
Warranty Information
Please fill in the warranty card immediately upon purchase and attach the invoice to the back. Keep both for maintenance. Present the warranty card and purchase invoice for service.
Warranty Terms:
- Speediance provides free maintenance service within the one-year warranty period, starting from the purchase date, provided the product is operated normally and in accordance with instructions.
- If the product is out of warranty and requires accessory replacement, a reasonable maintenance fee will be charged.
- The warranty does not cover:
- Products without a purchase or warranty certificate.
- Products out of the warranty period.
- Products disassembled or maintained by unauthorized personnel.
- Damage caused by misuse, negligence, or improper handling.
- Damage or malfunction due to non-typical household use (e.g., prolonged use in harsh environments).
- Products exhibiting natural wear and tear due to usage.
Signature of Distributor: [space for signature]
Regulatory Information
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
ISED Statement
English: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
French: Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement. L'appareil numérique du ciem conforme canadien peut - 3 (b) / nmb - 3 (b).
This device meets the exemption from the routine evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF exposure. Users can obtain Canadian information on RF exposure and compliance.
Cet appareil est conforme à l'exemption des limites d'évaluation courante dans la section 2.5 du cnr - 102 et conformité avec rss 102 de l'exposition aux rf, les utilisateurs peuvent obtenir des données canadiennes sur l'exposition aux champs rf et la conformité.
This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator & your body.
Cet équipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance minimale de 0 cm entre le radiateur et votre corps.
