CASIO

Water Protection

Important Information: Read First

For all watch categories, the following are prohibited:

• Pressing buttons underwater.
• Moving hands underwater.
• Unscrewing the crown underwater.

If the watch is exposed to salt water, rinse it thoroughly and dry it. Do not wear watches with leather straps while swimming. Avoid prolonged contact of leather straps with water.

Watches are classified by levels (from I to V) according to their degree of water protection. Check your watch's level using the table below to determine its proper use.

Notes:

• I Watches are not water-protected. Avoid any moisture ingress.
• II WR (Water Resistant) means the model is waterproof according to ISO 2281. Brief contact with water will not cause any problems.
• III With 5 Bar (50 meters) water resistance, the watch can withstand water pressure of the indicated value and can therefore be used while showering and for brief swimming.
• IV 10 Bar (100 meters) water resistance means the watch can be used during normal swimming and snorkeling.
• V 20 Bar (200 meters) water resistance means the watch can be used for scuba diving (except for depths requiring a helium-oxygen mixture).

When using the product in conditions of rapid temperature changes, slight condensation may form on the inside of the glass. This phenomenon is due to the laws of physics and is not a defect.

CASIO COMPUTER CO., LTD. is not responsible for any damage that may arise from the use of this watch, and does not accept any claims from third parties.

Crown Operation

Your watch may differ slightly from the illustrations in this manual.

Note: Some water-resistant watch models are equipped with a screw-lock crown.

To pull out such a crown, you must unlock it by turning it in the direction indicated by the arrow in the illustration. Do not use excessive force when pulling out the crown. This may lead to its damage.

Note that the watch becomes unprotected from water and moisture when the crown is pulled out. After completing all operations using the crown, return it to its original position and lock it.

Illustration: Watch crown with an arrow indicating the direction to turn for unlocking.

Setting the Current Time

Modules: 1362, 1398, 1770, 2799, 3378, 4370

Pull out the crown. Turn it to set the hands to the current time. Push the crown back to its original position.

Illustration: Watch face with the crown indicated.

Modules: 705, 706, 1300, 1311, 1330, 1344, 1360, 1399, 1747, 1771, 1782, 4328, 4394, 4747, 5049, 5284, 5361, 5364, 5375, 5577

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Turn the crown to set the hands to the current time. Set the minute hand 4-5 minutes ahead of the current time, then move it back.
3. When you hear the time signal, close and secure the crown.

Illustration: Two watch faces, one showing the crown and the other showing the crown and a date display. Module numbers 5284, 5361, 5364, 5375, 5577 are listed.

Modules: 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Turn the crown to set the hands to the current time. To fine-tune the current time, move the minute hand back 4-5 minutes from the desired value, then move it forward to the current value.
3. Push the crown back to its original position to resume time display.

Illustration: Watch face showing crown positions: Normal position, First click (date setting), Second click (time setting). A date display '30' is shown.

Modules: 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

Setting the Current Time

1. When the second hand is at the 12 o'clock position, pull out the crown. The second hand will stop.
2. Turn the crown to set the hands to the current time. To fine-tune the current time, move the minute hand back 4-5 minutes from the desired value, then move it forward to the current value.
3. Push the crown back to its original position to resume time display.

Illustration: Two watch faces showing crown positions: Normal position, First click (date and day of week setting), Second click (time setting). One shows 'SUN 30', the other 'WED 30'. Module numbers 709, 1333, 1347, 3716 are listed.

Setting the Date

Modules: 707, 708, 1331, 1332, 1335, 1336, 1342, 1345, 1346, 1369, 1370, 1373, 1701, 1710, 1711, 1787, 2717, 2718, 2719, 2725, 2731, 2748, 2749, 2783, 2784, 3363, 3711, 3712, 4393, 5025, 5044, 5058, 5116, 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532

To ensure the date changes at midnight, do not set the date between 8:00 PM and 2:00 AM.

1. Pull out the crown to the first click.
2. Turn it to set the desired date.
3. Push the crown back to its original position.

Illustration: Watch face showing crown positions: Normal position, First click (date setting), Second click (time setting). A date display '30' is shown. Module numbers 5128, 5180, 5199, 5206, 5207, 5218, 5250, 5340, 5341, 5342, 5343, 5352, 5358, 5383, 5393, 5436, 5507, 5532 are listed.

Modules: 709, 1309, 1333, 1334, 1347, 3716, 5125, 5167, 5223, 5237, 5249, 5339, 5373, 5458, 5474

Setting the Date and Day of the Week

To ensure the date and day of the week change at midnight, do not set the date between 8:00 PM and 2:00 AM.

1. Pull out the crown to the first click.
2. Set the date by turning the crown counter-clockwise.
3. Set the day of the week by turning the crown clockwise. Days of the week are indicated in English or Spanish.

4. Push the crown back to its original position.

Watches with Backlight

• Press and hold button L to illuminate the watch face.
• Depending on the watch model, the backlight duration is 2 to 3 seconds, or 1 second, or while button L is pressed (module 5577).
• Depending on the watch model, the face illumination is provided by electroluminescent (EL) elements or LEDs. EL elements lose power after prolonged use.
• Frequent use of the backlight shortens battery life.
• Turning on the backlight for an extended period or with a low battery charge may cause the watch hands to stop moving for a while.

Illustration: Two watch faces, showing the crown and the 'L' button for backlight.

Watches with Rotating Bezel

Rotate the bezel to align a mark with the minute hand. After some time, you can tell how much time has passed since the mark was aligned with the minute hand.

Illustration: A watch with a rotating bezel, used for measuring elapsed time.

Technical Specifications

Specifications are subject to change without prior notice.

Product Information

Name: Electronic / Electro-mechanical Quartz Wristwatch (Men's/Women's)

Brand: CASIO

Manufacturer: CASIO COMPUTER Co.,Ltd.

Manufacturer Address: 1-6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan

Importer: OOO 'Casio', 127015, Russia, Moscow, Butyrskaya St., bld. 77

Warranty Period: 2 years

Address of authorized organization for claims: Indicated on the warranty card