Fiamma Turbo-Vent Premium Rooflight

Product Overview

The Fiamma Turbo-Vent Premium is a high-quality roof vent designed for caravans and motorhomes, offering ventilation and light. It is available in White and Crystal finishes.

Key Components:

• Component A: The outer frame and transparent cover of the rooflight.
• Component B: The inner frame housing the fan and motor assembly.
• Component C: The internal trim ring, which typically includes a mosquito net.

Models and Specifications:

• Turbo-Vent Premium White: Model No. 03623H01- / 03623H01B
• Turbo-Vent Premium Crystal: Model No. 03624H02- / 03624H02D
• Weight: 4.6 kg

Certifications include UK, CA, CE, E24 (10R-06 0530), and E11 (43R-01 7019).

Technical Specifications

Installation Instructions

Before installation, ensure the roof thickness is compatible (30mm to 85mm).

1. Prepare Opening: Cut a square hole of 39cm x 39cm in the roof.
2. Electrical Connection: Arrange the electrical connection directly from a 12V DC battery. Ensure it is not connected to 220V.
3. Seal External Frame: Apply sealant (e.g., SIKALASTOMER-710, THEROSTAT II, or DEKALIN 1512) to the lower part of the external frame, following the designated rails for a minimum width of 30mm.
4. Position External Frame: Place the external frame into the prepared opening, ensuring the hinges face the front of the vehicle.
5. Fasten External Frame: Secure the external frame using 20 self-tapping screws (Ø4.2x30mm UNI EN ISO 7049). Carefully seal the entire perimeter of the frame, filling any gaps between the roof and the frame, and cover the screw heads with sealant.
6. Connect Motor: Connect the input cables of the electric motor.
7. Fasten Internal Frame: Secure the internal frame with 8 self-tapping screws (Ø3.5x15mm UNI EN ISO 7049).
8. Remove Protective Film: Carefully remove the protective plastic film from the cover. Avoid prolonged exposure to direct sunlight during this process, as it can make removal difficult.

Diagrams illustrate cutting the 39cm opening, electrical connection to a 12V battery, applying sealant, positioning the frame, securing with screws, connecting motor wires, and fastening the inner frame.

Polar Control Function

The Polar Control function automatically activates ventilation based on the set temperature difference (ΔT) and the outdoor temperature.

Operation:

• When the Polar Control function is activated, the system detects the ambient room temperature.
• By adjusting the control key (A) and the desired ΔT value, the fan will operate at the set speed until the target temperature is reached.
• Switching the Polar Control function on and off resets the displayed room temperature.
• To limit energy consumption, it is recommended to set the Polar Control to the minimum ΔT of 1°C once a comfortable room temperature is achieved.

Note: The cooling capacity of the fan is dependent on the difference between the outdoor temperature and the room temperature.

ΔT: Represents the difference between the detected room temperature and the desired temperature.

Diagrams show control panel indicators for different ΔT settings (ΔT-1°C to ΔT-5°C), Polar Control off, lowest cooling, and maximum cooling modes.

Care and Maintenance

For cleaning the interior and exterior of the rooflight, always use neutral, non-aggressive detergents.

• For cleaning the 'Crystal' cover, use an acrylic glass cleaner with a soft cloth to avoid scratching the surface.
• Never use aggressive products such as glass cleaners, all-purpose cleaners, abrasives, or dish-washing detergents.
• Avoid using alcohol-containing detergents, solvents, or any corrosive liquids.
• The mosquito net can be cleaned with water and a neutral detergent.

Safety and Troubleshooting

Safety Precautions:

• Fiamma declines responsibility for personal injury or property damage due to incorrect assembly or use. Keep instructions inside the vehicle.
• Do not modify the product.
• Periodically check the tightness of all screws, especially after initial kilometers and before/after long trips.
• If the opening/closing mechanism stiffens, lubricate it with a few drops of grease.
• Do not walk on the product cover.
• Ensure the rooflight is properly closed before starting the vehicle.
• Periodically check the cover for cracks.
• Do not open the rooflight while the vehicle is moving.
• Do not open the rooflight in strong wind or rain.
• Remove snow or ice from the rooflight.
• Always comply with speed limits and traffic regulations. Adjust speed according to traffic conditions and load.

Troubleshooting:

In case of problems, please contact your local dealer and provide the data from the nameplate. Consult the Fiamma website for spare parts drawings.

Icons indicate successful installation (thumbs up ?), unsuccessful installation (thumbs down ?), and conditions to avoid: strong sunlight ☀️, snow/ice ❄️, rain ?️.

Related Accessories

• Thermo Vent 40 (Item No. 03650A01-)
• Extension Vent Ivory (Item No. 98683-116)
• Extension Vent White (Item No. 98683-112)
• Rollo Vent 40x40 (Item No. 06310-02-)
• Spoiler Universal (Item No. 06289-01-)

Declarations and Warranty

The product conforms to relevant Union harmonisation legislation, including directives on Electromagnetic Compatibility (EMCD), Low Voltage (LVD), and Restriction of Hazardous Substances (RoHS).

Warranty: In case of defects regarding materials and manufacturing, the customer is entitled to warranty in accordance with local laws and regulations of the country where the product was purchased.