RC10 B74.2 Team Kit Setup Sheet
Driver: Daniel Pole (14)
Event: BRCA Scottish Regionals
Track: Dumfries
Date: May 2025
Qualify: A1 | TQ: Main A | Finish: A1 | Best Lap Time:
Front Suspension
| Parameter | Value | Diagram/Notes |
|---|---|---|
| Ride Height | 18mm | |
| Camber | -1.5deg | |
| Toe | + 0.5deg | |
| Anti-Roll Bar | 1.6mm | |
| Arm Type | Carbon | |
| Tower Type | Hall Brothers Tower | |
| Wheelbase Shim | Arm rearwards (Shim to front) | |
| Wheel Hex | 4mm | |
| Caster Block | 8° 9° 10° | [Checkbox for 9° selected] |
| Chassis Brace Support | Kit | |
| Top Plate Brace | Carbon | |
| Front Axles | CVA DCV | [CVA selected] |
Kit: B74.2d Kit
Front Chassis Brace Screws:
Ball Stud Spacing: 3mm
Arm Mount A: [Diagram showing hole pattern]
Arm Mount B: [Diagram showing hole pattern]
Axle Height: +3 +2 +1 0 [+2 selected]
Ball Stud Spacing: 0
Steering Plate: Jamie Hall's
Diff Height: +2 +1 0 [+1 selected]
Ball Stud Spacing: 1mm
Rear Suspension
| Parameter | Value | Diagram/Notes |
|---|---|---|
| Ride Height | 18mm | |
| Camber | -2.0deg | |
| Anti-Roll Bar | 1.7mm | |
| Arm Type | Kit | |
| Wheelbase Shim | Arm Forwards (Shim to Rear) | |
| Wheel Hex | 7mm | |
| CVA Bone Length | Kit | |
| Chassis Brace Support | Kit | |
| Hub Spacing | Fwd Mid Back | [Mid selected] |
Hall Brothers Towers
Centro Fan on Motor
Rear Chassis Brace Screws:
Arm Mount C: [Diagram showing hole pattern]
Arm Mount D: [Diagram showing hole pattern]
Axle Height: +3 (+0/3) +2 (+0/2) +1 (+0/20) +0 (+0/30) [+2 selected]
Diff. Height: +3 +2 +1 0 [+1 selected]
Camber Link Spacing: 2mm
Ball Stud Spacing: 2mm
Electronics, Drivetrain
| Component | Details | Notes |
|---|---|---|
| Radio | Sanwa M17S | |
| Servo | Savox SC1258TG | |
| EPA | Throttle: 100% | Brake: 90% |
| ESC | Reedy 610R | ESC Settings: 0 boost 20 turbo |
| Motor | Reedy Sonic M4/5.5 | Timing: 20 |
| Pinion | 19 | |
| Spur | 78 | |
| Diffs (Front/Center/Rear) | Fluid: 15k / 500k / 15k | Gears: 2x LTC Kit / 4x HTC Kit / 2x LTC Kit |
| Type | Metal / Metal / Metal | AS92320 Alu Gearbox height bearing holder, AS92322 FT Diff Crosspins |
| Shocks (Front/Rear) | Fluid: 42.5w / 30w | Piston: 2x 1.7mm 2.5mm thick - 13mm / 3x1.7mm 2mm thick - 13mm |
| Spring | Red v2 / Blue v2 | |
| Limiters | Int: 0 Ext: 0 / Int: 0 Ext: 0 | 12mm cups, Chrome shafts (AS91618, AS91620) |
| Stroke | 23.0mm / 27.8mm | Machined internals (AS91494) |
| Eyelet Length | Short 0 / Short 0 | |
| Cup Offset | 9mm / 0mm | |
| Battery | Back 1 2 3 4 Fwd | [4 selected] |
| Battery Position | Reedy zapper 4800mah LCG | |
| Slipper Clutch | # of Pads |
Track Info, Tires & Aero
| Category | Selection | Options |
|---|---|---|
| Layout | Tight Mixed Open Extra Large | [Extra Large selected] |
| Surface | Dirt Carpet Astroturf | [Dirt selected] |
| Traction | Low Medium High Very High | [Very High selected] |
| Moisture | Dry Damp Wet | [Damp selected] |
| Condition | Indoor Outdoor Dusty Hard Packed | [Indoor selected] |
| Bumpy Grooved Smooth Loamy | [Smooth selected] | |
| Temperature | Ambient: 17deg | Humidity: |
| Front Tires | Schumacher Mezzo (2+2) | Front Compound: Yellow |
| Front Insert | Cragg Foam | |
| Rear Tires | Schumacher Mezzo | Rear Compound: Yellow |
| Rear Insert | Cragg Foam | |
| Wheel (F/R) | Schumacher/Centro | [Rotate wheels 2mm wider so using only 4mm hex] |
| Body | Kit | |
| Rear Wing | Centro | Wing Angle: 0° 6° [6° selected] |
| Wing Mount Height | 0 -2 [0 selected] | |
| Front Wing | Yes No [Yes selected] | |
| Servo Weights | No | |
| Electronic Weights | No | |
| Total Vehicle Weight: |
Comments
Track wet grass drying to blown out grass
Pace was awesome. Changed toe through the day depending on grip. Used Ballistic Green in wet/damp.