Team Associated RC10 B74.2 Setup Sheet
Driver: Daniel Pole (14) | Event: BRCA Junior & Vets | Track: BMR | Date: June 2025
Qualify: A1 | TQ: | Main: A1 | Finish: A1 | Best Lap Time: 20.2
Front Suspension
Ride Height: 16mm
Camber: -2.0deg
Toe: +0.5deg
Anti-Roll Bar: 1.6mm
Arm Type: Carbon
Tower Type: Hall Brothers Tower
Wheelbase Shim: Arm rearwards (Shim to front)
Wheel Hex: 4mm
Caster Block: [ ] 8° [ ] 9° [x] 10°
Chassis Brace Support: Kit GRP
Top Plate Brace: Carbon
Front Axles: CVA [ ] DCV [x]
Diagrams:
- Front Chassis Brace Screws: Two screws shown.
- Ball Stud Spacing: 3mm: Visual representation of 3mm ball stud spacing.
- Arm Mount A: Mounting plate with multiple hole positions indicated, some highlighted with red dots.
- Arm Mount B: Similar mounting plate with different hole positions and red dots.
- Diff Height: Adjustment points labeled +2, +1, 0 for differential height.
- Axle Height: Adjustment points labeled +3, +2, +1, 0 for axle height.
- Steering Plate: Kit +2: Steering plate with a "+2" indicator.
- Ball Stud Spacing: 1mm: Visual representation of 1mm ball stud spacing.
- Vertical Ball Stud Mount: Mount with adjustment options for ball stud spacing (e.g., +3 (0/3)).
- Camber Link Spacing: 2mm: Measurement of 2mm for camber link spacing.
- Ball Stud Spacing: 0mm: Visual representation of 0mm ball stud spacing.
Notes: B74.2d Kit
Rear Suspension
Ride Height: 16mm
Camber: -2.0deg
Anti-Roll Bar: 1.7mm
Arm Type: Kit
Wheelbase Shim: Arm Rearwards (Shim to front)
Wheel Hex: 6mm
CVA Bone Length: Kit
Chassis Brace Support: Kit - GRP
Hub Spacing: Fwd [ ] Mid [ ] Back [x]
Components: Hall Brothers Towers, Centro Fan on Motor
Diagrams:
- Rear Chassis Brace Screws: Screws shown.
- Arm Mount C: Mounting plate with hole patterns and red dots.
- Arm Mount D: Mounting plate with hole patterns and red dots.
- Diff. Height: Adjustment points labeled +3, +2, +1, 0 for differential height.
- Axle Height: Adjustment points labeled +3, +2, +1, 0 for axle height.
- Ball Stud Spacing: 0mm: Visual representation of 0mm ball stud spacing.
Electronics, Drivetrain
Radio: Sanwa M17
Servo: Reedy
EPA: Throttle: 100% | Brake: 91%
ESC: Reedy 610R
ESC Settings: 0 boost 25 (turbo)
Motor: Reedy Sonic M4 5.5 Timing: 20
Pinion: 19
Spur: 78
Battery: Position: Back [ ] 1 [ ] 2 [ ] 3 [ ] 4 [x] Fwd [ ]
Battery Position: Reedy zapper 4800mah LCG
Slipper Clutch: - | # of Pads: -
Notes: AS92320 Alu Gearbox height bearing holder, AS92322 FT Diff Crosspins * Critical for 2gears*
Diffs
| Front | Center | Rear | |
|---|---|---|---|
| Fluid | 15k | 500K 15k | 15k |
| Gears | 2x LTC Kit | 4xHTC | 2x LTC Kit |
| Type | Metal | Metal | Metal |
Notes: 12mm cups, Chrome shafts (AS91618, AS91620) Machined internals(AS91494)
Shocks
| Front | Rear | |
|---|---|---|
| Piston | 2x 1.7mm 2.5mm thick - 13mm | 3x1.7mm 2mm thick - 13mm |
| Fluid | 45w | 30w |
| Spring | Orange v2 | Blue v2 |
| Limiters | Int: 0 Ext: 0 | Int: 0 Ext: 0 |
| Stroke | 23.0mm | 27.8mm |
| Eyelet Length | Short 0 | Short 0 |
| Cup Offset | 5mm | 0mm |
Track Info, Tires & Aero
Layout: Tight [ ] Mixed [ ] Open [x] Extra Large [ ]
Surface: Dirt [ ] Carpet [ ] Astroturf [x]
Traction: Low [ ] Medium [x] High [ ] Very High [ ]
Moisture: Dry [x] Damp [ ] Wet [ ]
Condition: Indoor [ ] Outdoor [ ] Dusty [ ] Hard Packed [ ] Bumpy [ ] Grooved [x] Smooth [ ] Loamy [ ]
Temperature: Ambient: 25deg
Humidity: dry
Front Tires: Sch Mezzo 2+2
Front Compound: Yellow
Front Insert: Cragg
Rear Tires: Sch Mezzo
Rear Compound: Yellow
Rear Insert: Cragg
Wheel (F/R): Centro
Notes: Schu frt wheels ar 2mm wider so using only 4mm hex
Wing Angle: 0° [x] 6° [ ]
Wing Mount Height: 0 [x] -2 [ ]
Front Wing: Yes [ ] No [x]
Servo Weights: No
Electronic Weights: No
Total Vehicle Weight:
Body
Body: Kit
Rear Wing: Centro
Comments
Pace was awesome.
