Team Associated B84 RC Car Setup Sheet
Driver: Daniel Pole (14)
Date: July 2025
Event: BRCA Regionals SORS | Track: Stonehaven Astro | Qualify: A1 | Finish: A | Main: A1 | Best Lap Time:
Front Suspension
| Parameter | Value | Notes/Options |
|---|---|---|
| Ride Height | 16mm | |
| Camber | -1.5° | |
| Toe | 0.5° out | |
| Anti-Roll Bar | 1.4mm | |
| Arm Type | Kit | |
| Tower Type | #92545 Kit | |
| Wheelbase Shim | Arm forwards (Shims to rear) | |
| Wheel Hex | 5mm | |
| Steering Block Type | #92171 Kit | |
| Caster Block | -2°, -1°, 0°, +1°, +2° | |
| Chassis Brace Material | #92503 Kit | |
| Top Plate Brace Material | #92503 Kit | |
| Front Axles | CVA DCV |
Adjustment Options
Lower Brace Type: Fixed Pivot
Arm Mount A: 1° (Grey hole pattern), 0.5° (Black hole pattern)
Arm Mount B: 1° (Grey hole pattern), 0.5° (Black hole pattern)
Axle Height: Options: +3, +2, +1, 0, -1, -2, -3
Ball Stud Spacing: 0mm
Steering Plate: Hall Brothers
Diff Height: Options: +3, +2, +1, +0, -1, -8
Ball Stud Spacing: 1mm
Rear Suspension
| Parameter | Value | Notes/Options |
|---|---|---|
| Ride Height | 16mm | |
| Camber | -2.0° | |
| Anti-Roll Bar | 1.3mm | |
| Arm Type | Kit | |
| Tower Type | #92546 Kit | |
| Wheelbase Shim | Arm Rearwards (Shims to front) | |
| Wheel Hex | 5mm | |
| Hub Type | #92412 HRC Kit | |
| Drive Shaft Type | #92454 Kit 69mm CVD | |
| Chassis Brace Material | #92503 Kit | |
| Upper Chassis Brace Material | #92504 Kit | |
| Hub Spacing | Fwd, Mid, Back | |
| Notes | Centro 0-4Deg C Block (C0255) |
Adjustment Options
Lower Brace Type: Fixed Pivot
Rear Chassis Brace Screws: (No specific value listed)
Arm Mount C: 1° (Grey hole pattern), 0.5° (Black hole pattern)
Arm Mount D: 1° (Grey hole pattern), 0.5° (Black hole pattern)
Axle Height: Options: +3, +2, +1, 0, -1, -2, -3
Gearbox: Standard, +2
Camber Link Spacing: 2mm
Ball Stud Spacing: 1mm
Diff Height: Options: +3, +2, +1, +0, -1, -8
Electronics
| Parameter | Value |
|---|---|
| Radio | Sanwa M17S |
| Servo | Reedy RS1606A |
| EPA: Throttle | 100% |
| EPA: Brake | 70% |
| ESC | Reedy 610R |
| ESC Settings | 20 Turbo |
| Motor/Wind | Reedy Mach4 5.5t |
| Timing | Std |
| Pinion | 19t |
| Spur | 78t |
| Motor Position | Forward / Back |
| Battery Position | Back 1, 2, 3, 4, 5 Forward |
| Battery | Reedy zapper 4800mah LCG |
| Weight | (Not specified) |
Differential
| Front | Center | Rear | |
|---|---|---|---|
| Fluid | 15k | 500k | 15k |
| Gears | 4x LTC kit | 4x HTC | 4x LTC Kit |
| Piston | #71173 3x1.6mm 13mm | #71174 3x1.7mm 13mm | #71173 3x1.6mm 13mm |
| Thickness | 2mm | 2mm | 2mm |
| Fluid | 40w | 30w | 40w |
| Spring | Orange v2 12mm | Yellow v2 12mm | Orange v2 12mm |
Shocks
| Front | Rear | |
|---|---|---|
| Type | Metal #92306 | Metal #92306 |
| Limiters | Int: Ext: 1 xring | Int: Ext: 1 xring |
| Stroke | 22.3mm | 27.2mm |
| Eyelet | 0 | 0 |
| Cup Offset | 0 | +5 |
| Kashima Bodies | (Not specified) | (Not specified) |
| Chrome Shafts | (Not specified) | (Not specified) |
| Machined Spacers | (Not specified) | (Not specified) |
Slipper Clutch
| Parameter | Value |
|---|---|
| Type | (Not specified) |
| # of Pads | (Not specified) |
| Setting | (Not specified) |
| Notes | (Not specified) |
Track Info
| Parameter | Value |
|---|---|
| Size | Medium |
| Surface | Astro (Bury type with NO sand) |
| Traction | High/Very High |
| Moisture | Dry (Wet earlier in the day) |
| Condition | Outdoor, Bumpy in places |
| Temperature | 20 deg |
Tires
| Parameter | Value |
|---|---|
| Front Tires | Sch Mezzo (2 rows off both sides + glue on sidewal) |
| Front Compound | Yellow |
| Front Insert | Cragg Foam |
| Rear Tires | Sch Mezzo |
| Rear Compound | Yellow |
| Rear Insert | Cragg Foam |
| Wheel (F/R) | Schumacher/Centro |
Body & Weight
| Parameter | Value |
|---|---|
| Body | Kit |
| Front Wing | (Not specified) |
| Rear Wing | Kit |
| Rear Wing Mount | 0, -2 |
| Wing Angle | 0°, 3°, 6° |
| Chassis Length | Kit |
| Total Vehicle Weight | (Not specified) |
Vehicle Comments
Centre diff in forward position
Still improving setup. HRC rear hubs an improvement
Centro 0-4Deg C Block (C0255)
When wet we ran 1mm higher ride height and more rear toe in.
In wet we ran silver mezzo tyres.
Tried Universal joint driveshafts briefly and was better on bumps BUT UJ's had too much rotation so will need to modify setup to suit
Resources
For more setups, visit: https://www.associatedelectrics.com/teamassociated/manuals_and_setup_sheets/
