VEVOR Metal Chicken Coop

Product Overview

VEVOR is committed to providing tools at competitive prices. Phrases like "Save Half" or "Half Price" represent an estimate of potential savings compared to major brands and do not necessarily apply to all product categories. Customers are advised to verify savings carefully when placing an order.

Need Help? Contact Us!

For product questions or technical support, please contact VEVOR via their website: www.vevor.com/support.

This is the original instruction manual. Please read all instructions carefully before operating. VEVOR reserves the right to interpret its user manual. Product appearance may vary. VEVOR will not provide advance notice for technology or software updates.

Safety Instructions

WARNING

Read this material before using this product. Failure to do so can result in serious injury.

Assembly Precautions

• Assemble only according to these instructions. Improper assembly can create hazards.
• Wear ANSI-approved safety goggles ? and heavy-duty work gloves ? during assembly.
• Keep the assembly area clean and well-lit.
• Keep bystanders out of the area during assembly.
• Do not assemble if tired or under the influence of alcohol, drugs, or medication.
• Product capabilities apply only to properly and completely assembled products.
• Assemble on a flat, level, hard, and smooth surface capable of safely supporting the metal chicken coop.
• For additional information regarding parts, refer to the Assembly Diagram. Unwrap and separate all parts in a clean work area.

Use Precautions

• DO NOT SIT OR STAND ON THIS ITEM.
• This product is not a toy. Do not allow children to play with or near this item.
• Do not exceed specified weight capacities.
• Use only on a flat, level, hard, and smooth surface that can safely support a fully loaded metal chicken coop.
• Use as intended only.
• Inspect before every use; do not use if parts are loose or damaged.

SAVE THIS MANUAL

Tools

Required tools include: Gloves ?, Safety Goggles ?, Drill ड्रिल, Screwdriver ?.

Parts List

Assembly Steps

Step 1: Assemble the Base Frame

Connect parts 1, 2, 5, and 6 to parts C and D. Use part P to secure the base. Ensure button clips are used for connections. Pay attention to the orientation of Part P.

Step 2: Attach Vertical Poles

Attach vertical poles (Part 3Y) to the corners of the base frame (Part C). Use part 9 to connect. Ensure the button clips on Part C are pointing left and right.

Step 3: Install Horizontal and Angled Supports

Install horizontal and angled supports. Connect parts AY and BY to the vertical poles. Use AY-2 for specific connections.

Step 4: Attach Roof Arches

Attach the arched roof supports. Connect parts 4Y and BY-1 to the frame structure.

Step 5: Install Main Roof Arch Components

Install the main roof arch components. Connect parts D1, D2, D4Y, D5Y, and D7Y to the frame. Use parts H and K as connectors. Screw L is used to secure H into tube D7Y; a power tool is recommended.

Step 6: Add Intermediate Supports

Add intermediate supports. Connect parts D3 and D6Y. Use parts H and K for securing. Ensure D6Y is fully covered by the two pairs of H. Use screw L to secure H after adjusting D3 and D6Y.

Step 7: Attach Final Frame Components

Attach the final frame components. Connect part D8 and K to the structure.

Step 8: Attach Poultry Net

Attach the poultry net (Part F). Roll the net along the tubes of the assembled structure and cut it as needed. Use zip-ties to fasten the net to the tubes. Overlaps between nets are expected. Follow the directional arrows for guidance.

Net Placement Note

For the net at the back of the coop, roll the net without measuring. For the net at the front, it is recommended to measure and cut the net first. The front rectangular area may require careful handling as the net roll's width might not cover it completely when rolled vertically. Always follow the arrows for rolling and cutting.

Product Parameters

Manufacturer and Importer Information

Manufacturer: Shanghaimuxinmuyeyouxiangongsi

Address: Shuangchenglu 803nong11hao1602A-1609shi, baoshanqu, shanghai 200000 CN.

Imported to AUS: SIHAO PTY LTD. 1 ROKEVA STREETEASTWOOD NSW 2122 Australia

Imported to USA: Sanven Technology Ltd. Suite 250, 9166 Anaheim Place, Rancho Cucamonga, CA 91730

EU Representative: E-CrossStu GmbH, Mainzer Landstr.69, 60329 Frankfurt am Main.

UK Representative: YH CONSULTING LIMITED. C/O YH Consulting Limited Office 147, Centurion House, London Road, Staines-upon-Thames, Surrey, TW18 4AX