Rev-Light WiFi Light Switch & 433MHz

Warranty Registration & Support

Register your warranty by filling out the online form at www.chacon.com/warranty.

For video tutorials, visit the DiO Connected Home YouTube channel: youtube.com/c/dio-connected-home.

For support, visit www.chacon.com/support.

1. Installation Guide

This product should be installed by a qualified electrician in accordance with installation rules. Incorrect installation or use may pose a risk of electric shock or fire. Always cut the power supply before performing any work.

Prepare cables by stripping approximately 8mm of insulation for good contact.

Wiring Connections:

• Connect the power supply's Line (L) wire (brown or red) to the module's 'L' terminal.
• Connect the wire from the light bulb (brown or red) to the module's 'L1' terminal.
• Connect the capacitor in parallel with the light bulb for optimal performance.

Diagram Description (Fig. 1): Illustrates the wiring connections between the power source, the light switch module, the light bulb, and the parallel capacitor.

2. Linking with DiO 1.0 Devices

This switch is compatible with all DiO 1.0 devices (remote controls, switches, detectors).

To link a device:

1. Press the switch's central button twice quickly. The LED will start to flash slowly in light green.
2. Within 15 seconds, press the 'ON' button on your DiO remote control. The switch's LED will flash light green quickly to confirm the association.

Warning: If the 'ON' button is not pressed within 15 seconds, the switch will exit learning mode.

The switch can be linked to a maximum of 6 DiO devices. If the memory is full, you cannot add a 7th device.

Diagram Description (Fig. 2): Shows the pairing process between a remote control and the switch, indicating button presses and LED feedback.

2.1 Deleting DiO Device Links

To delete a specific device:

1. Press the switch's central button twice quickly (LED flashes slow green).
2. Press the 'OFF' button on the DiO device you wish to delete. The LED will flash light green rapidly to confirm deletion.

To delete all registered DiO devices:

• Press and hold the switch's pairing button for 7 seconds until the LED indicator turns purple, then release.

3. Adding the Switch to the DiO One Application

3.1 Create Your DiO One Account:

• Scan the QR code to download the free DiO One application (available on iOS App Store and Android Google Play).
• Follow the in-app instructions to create your account.

Diagram Description (Fig. 3): Depicts scanning a QR code to access the DiO One mobile application.

3.2 Connect the Switch to Your Wi-Fi Network:

1. In the DiO One app, navigate to "My devices", tap "+", then select "Install Connect Wi-Fi device".
2. Choose "DiO Connect Light switch".
3. Power on the DiO switch and press its central button for 3 seconds. The LED indicator will flash red quickly.
4. Within 3 minutes, tap "Install the Connect Wi-Fi device" in the app.
5. Follow the on-screen installation wizard.

Wi-Fi/Password Change: If your Wi-Fi network or password changes, press the switch's pairing button for 3 seconds. Then, in the app, perform a long press on the device icon and follow the instructions to update the Wi-Fi settings.

3.3 Disable Wi-Fi from the Switch:

• Press and hold the central button for 3 seconds, release, then double-click to disable the switch's Wi-Fi. The LED will turn steady purple.
• To re-enable Wi-Fi, repeat the process: press and hold for 3 seconds, release, then double-click. The LED will indicate Wi-Fi connection status.

Note: Timers created via the smartphone app will remain active even when Wi-Fi is disabled on the switch.

3.4 Switch LED Status Indicators:

• Steady Red: Switch is not connected to the Wi-Fi network.
• Flashing Blue: Switch is connected to Wi-Fi.
• Steady Blue: Switch is connected to the Cloud (will turn white after a few seconds).
• Steady White: Switch is ON (can be turned off via app in discreet mode).
• Steady Purple: Wi-Fi is disabled.
• Flashing Green: Firmware update is downloading.

3.5 Connect with Your Voice Assistant:

• Activate the "One 4 All" service or skill in your voice assistant (e.g., Alexa, Google Assistant).
• Enter your DiO One account credentials.
• Your DiO devices will automatically appear in your voice assistant's app.

4. Resetting the Switch

Press and hold the switch's pairing button for 12 seconds until the LED flashes light blue, then release. The LED will blink red twice to confirm the reset.

5. Usage

With DiO Remote Control/Switch: Press the 'ON' or 'OFF' button on your DiO control to turn the light on or off.

On the Switch: Press the corresponding button once to turn the light on or off.

With Your Smartphone (via DiO One App):

• Turn lights on/off from anywhere.
• Create programmable timers: set precise on/off times, select days of the week, and choose single or repeated schedules.
• Set countdown timers: lights will automatically turn off after a specified duration.
• Enable presence simulation: select absence duration and active periods; the switch will turn on/off randomly to deter potential intruders.

6. Troubleshooting

Issue: Light does not work with a DiO control or detector.

• Verify the switch is correctly connected to the electrical supply.
• Check battery polarity and charge levels in your DiO devices.
• Ensure the switch's memory is not full (maximum 6 DiO devices can be linked). Refer to section 2.1 for deletion.
• Confirm you are using a device compatible with the DiO 1.0 protocol.

Issue: Switch does not appear in the application interface.

• Check the switch's LED status:
  • Red LED: Check your Wi-Fi router status.
  • Flashing Blue LED: Check internet access.
• Ensure your Wi-Fi and internet connection are functional and within the switch's range.
• Verify your Wi-Fi is operating on the 2.4GHz band (5GHz is not supported).
• During setup, your smartphone must be connected to the same Wi-Fi network as the switch.
• A switch can only be added to one account. All household members should use a single DiO One account.

Important Note: Maintain a minimum distance of 1-2 meters between DiO receivers (modules, plugs, bulbs). Wall thickness or existing wireless environments may reduce the effective range between the switch and DiO devices.

7. Technical Specifications

• Protocol: 433.92 MHz by DiO
• Wi-Fi Frequency: 2.4GHz
• EIRP: Max. 0.7 mW
• Transmission Range (with DiO devices): 50m (in open field)
• Max Associated Devices: 6 DiO transmitters
• Operating Temperature: 0°C to 35°C
• Power Supply: 220-240 V ~ 50 Hz
• Max Load: 200W
• Dimensions: 85 x 85 x 37 mm

8. Supplementing Your Installation

This product is for indoor use only (IP20) and should not be used in damp environments.

Expand your smart home system with DiO solutions to control heating, lighting, roller shutters, garden features, or use video surveillance. DiO Connected Home products are designed to be easy to use, high-quality, scalable, and economical. Explore all solutions at www.chacon.com.

9. Recycling Information

In accordance with European WEEE (2002/96/EC) and accumulator (2006/66/EC) directives, electrical and electronic devices, as well as batteries, must be collected separately. Do not dispose of this product with household waste. The crossed-out wheelie bin symbol indicates that this product should not be disposed of with domestic waste in any EU country. Recycle responsibly to prevent environmental or human health risks and promote sustainable resource use. Return used devices through designated collection systems or contact the original dealer for recycling.

10. Declaration of Conformity

CHACON declares that the Rev-Light device complies with the requirements and provisions of Directive RED 2014/53/EU. The full text of the EU declaration of conformity is available at: www.chacon.com/en/conformity.