EZCast Pocket RX & TX User Manual

About EZCast Pocket

How to Mirror

1. Install the Receiver

   Connect the EZCast Receiver to the HDMI port on your TV using the USB Type-C connector. Power the receiver using an independent 5V/1A power adapter.

2. Plug and Play

   Connect the EZCast Transmitter to a USB Type-C or HDMI port on your laptop or mobile device. Wait a few seconds until the transmitter's flashing light stops; mirroring will begin automatically.

   For the Transmitter H-1 (HDMI connector), use the USB Type-C connector to provide independent power (5V/1A).

   Diagram Description: Shows the EZCast Receiver connected to a TV via HDMI and powered by a 5V/1A adapter. The EZCast Transmitter is shown connected to a laptop. A wireless signal icon indicates the connection.

3. Stop and Restart Mirroring

   Press the Mirror / Pair button on the transmitter to stop or restart mirroring.

   Diagram Description: Close-up of the EZCast TX transmitter, with a finger pressing the 'Mirror / Pair' button.

   Note: EZCast Transmitters support mirroring for all laptops (Windows and macOS) and Android mobiles with DP Alt output. To reset to default settings, press and hold the reset button for 5 seconds.

How to Pair Transmitter with Receiver

1. Turn on Pairing Mode for the Receiver

   1. Power up the receiver using an external 5V/1A adapter.
   2. Plug the receiver into the HDMI port on the monitor.
   3. Press and hold the reset button on the receiver for 2 seconds. Release when the screen displays "Release the button to pair with EZCast".

   Diagram Description: Sequence illustration: 1. A 5V/1A power adapter connected to the EZCast Receiver. 2. The Receiver plugged into an HDMI port on a monitor. 3. A timer graphic showing '2 secs' next to the Receiver's reset button. Text on the monitor reads 'Release the button to pair with EZCast'.

2. Press the Mirror / Pair Button on Transmitter

   Connect the transmitter to your laptop or mobile. If using the Transmitter H-1, ensure it receives power via its USB Type-C connector. Press and hold the mirror/pair button on the transmitter for 5 seconds until the screen shows "Ready to pair". After successful pairing, casting will begin automatically.

   Diagram Description: Illustration shows the EZCast TX transmitter connected to a laptop. A hand is shown pressing the 'Mirror / Pair' button for '5 secs'. Text on the laptop screen reads 'Ready to pair'.

   Note: The receiver's reset button has two modes based on press duration:

   • Press for 2 seconds: Activates pairing mode for the transmitter.
   • Press for 10 seconds: Resets the receiver to default settings.

OTA Upgrade

1. Download EZCast App

   1. Connect the receiver to the monitor and provide power using the USB Type-C connector.
   2. Scan the QR code with a computer or mobile phone, or visit www.ezcast.com/app to download the EZCast app.

2. Enabling Receiver SSID and PSK and Connect to It

   1. Check the monitor for the receiver's displayed SSID and PSK. If not visible, press the receiver's reset button for 2 seconds to enable pairing mode for display.
   2. Connect your mobile or computer's Wi-Fi to the receiver's network (SSID).
   3. Launch the EZCast app, select the receiver's SSID, and connect to it.
   4. Navigate to the settings page ⚙️, select "Internet", and connect the receiver to the internet.
   5. Check the Wi-Fi icon ✔️ on the monitor to verify the receiver is connected to the network.

   Diagram Description: Shows the EZCast Pocket RX receiver displaying its Wi-Fi network name (SSID) and password (PSK). A mobile device is shown connecting to this Wi-Fi network.

3. Using the EZCast App to Upgrade

   1. Ensure your mobile or computer is connected to the same Wi-Fi network as the receiver.
   2. Launch the EZCast app, select the receiver, and confirm the connection.
   3. The app will automatically check for the current version status. If a newer version is available, agree to update to complete the system upgrade.

   Diagram Description: A three-step process graphic: 1. A device labeled 'Pocket-xxx' connects to 'Internet'. 2. The connection is confirmed. 3. An 'Upgrade' screen with a checkmark symbol ✔️ is displayed.

Product Information

Transmitter

• Antenna: 1T1R (on board)
• Wi-Fi: 5Ghz
• Interface: HDMI or USB Type-C

Receiver

• Antenna: 1T1R (on board)
• Wi-Fi: 5Ghz
• Interface: HDMI

MIC Statement

Note: 5G band (W52) is for indoor use only.

NCC Statement

取得審驗證明之低功率射頻器材,非經核准,公司、商號或使用者均不得擅自變更頻率、加大功率或變更原設計之特性及功能。低功率射頻器材之使用不得影響飛航安全及干擾合法通信;經發現有干擾現象時,應立即停用,並改善至無干擾時方得繼續使用。前述合法通信,指依電信管理法規定作業之無線電通信。低功率射頻器材須忍受合法通信或工業、科學及醫療用電波輻射性電機設備之干擾。

FCC Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Exposure Statement

To maintain compliance with FCC's RF Exposure guidelines, this equipment should be installed and operated with a minimum distance of 20cm from the radiator to your body. This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.