ASC-2680 Premium HD Video Drone

ASC-2680 Diagram

The ASC-2680 drone features a camera and four propellers.

Controller Diagram

The controller includes: Power Button, ON/OFF & Power Indicator, Speed Setting Button, 360° Stunt Rolls Button, Emergency Stop, Throttle/Yaw control, Turning Left/Right Trim, Forward/Backward Trim, AUTO Start/AUTO Land, Direction Controls (including buttons for taking photos and starting/stopping video recording), and Banking Left/Right Trim.

Flight Warnings

WARNING: DO NOT FLY YOUR ASC-2680 IN FOUL WEATHER!

Ensure the remote control has 4 "AAA" batteries and the ASC-2680 rechargeable battery is fully charged. Fly in a large, open space (at least 400 feet radius) on a clear, level surface. For beginners, avoid windy conditions.

Syncing Your ASC-2680

To sync the drone and controller:

1. Ensure the controller is off and the drone battery is removed.
2. Place the drone on a flat, level surface. Press and hold the drone's power button until its LED lights flash rapidly (Diagram G).
3. Turn on the remote control. The controller's top red LED will flash.
4. Push the throttle stick all the way up, then pull it all the way down. You should hear a beep.
5. If the drone and controller lights become solid, syncing is successful. If not, repeat steps 1-4.

SPECIAL NOTE:

• Minimize the time between powering on the drone and controller to avoid sync timeouts.
• Syncing in shade can make LED indicators easier to see.
• The remote will beep if the drone is too far away; fly it closer.
• If the signal is lost, the drone will descend and land autonomously. Blue LED lights will flash until the battery is depleted.
• A rapid sequence of five beeps indicates the drone has exceeded 50 feet altitude, warning of potential loss of control in high winds. Avoid flying above 50-60 feet.

Diagram G: Demonstrates moving the throttle stick up and down to sync the drone and controller, with a note about LED light status changes.

Getting Ready to Fly

Once synced, familiarize yourself with starting/stopping rotors, auto-land, and control functions. Practice in a large, open area with minimal wind. Do not attempt high-altitude flights until experienced.

Identifying Front and Rear

The front of the ASC-2680 is indicated by the camera; the rear has a red light (Diagram H).

Diagram H: Shows the drone with the front identified by the camera and the rear by a red light.

Starting and Stopping Rotors

Auto Start/Auto Land: Press the AUTO START/LAND button on the controller (Diagram I) for automatic takeoff or landing. Direction can still be controlled during these processes.

Diagram I: Points to the AUTO START/LAND button on the controller.

Manual Start/Stop:

• To start rotors manually, move both control sticks simultaneously to the inside or outside corners (Diagram J), hold until rotors spin, then release to neutral and push throttle up to take off.
• To stop rotors: a) Land the drone, and rotors stop within ten seconds. b) Immediately stop by moving both control sticks simultaneously down to the inside or outside bottom corners (Diagram J). c) For EMERGENCY STOP, press the SPEED button and STUNT button simultaneously (Diagram K).

Diagram J: Illustrates moving control sticks to corners for manual start/stop.

Diagram K: Shows pressing the SPEED and STUNT buttons for emergency stop.

Speed Select Button

The ASC-2680 has four speed settings: T (Training), 1 (SLOW), 2 (MEDIUM), and 3 (HIGH). The default is SLOW. Press the speed setting button to cycle through speeds, indicated by beeps.

Training Mode (T Mode)

Press and hold the Speed Setting Button until a long beep is heard; arm lights will flash slowly. T Mode offers slow speed and set height limits for learning. Short press the speed setting button to exit T Mode.

Range Warning

If the drone's altitude exceeds 50 feet, the remote emits 5 rapid beeps. Before signal loss, a continuous warning sound and flashing blue lights on the drone indicate the signal is about to be lost. Bring the drone closer. If the signal is lost, the drone will descend and land autonomously.

Optical Flow Technology

This technology uses a downward-facing camera to analyze the ground and maintain a stationary position, counteracting drift caused by wind or other factors. It functions effectively at altitudes below 30 feet.

Flight Control

Mastering flight involves practicing basic controls:

• Ascend/Descend: Move the left throttle stick up to ascend, down to descend (Diagram L).
• Horizontal Rotation: Move the left throttle stick left for counter-clockwise rotation, right for clockwise rotation (Diagram L1).
• Forward/Backward Movement: Move the right direction control stick forward to move forward, backward to move backward (Diagram L2).
• Banking: Move the right direction control stick left to bank left, right to bank right (Diagram L3).

Diagram L: Shows the left throttle stick controlling ascent/descent.

Diagram L1: Shows the left throttle stick controlling horizontal rotation.

Diagram L2: Shows the right direction control stick controlling forward/backward movement.

Diagram L3: Shows the right direction control stick controlling banking.

Flight Practice

Practice simple maneuvers like vertical takeoffs, landings, and turns. Progress to square and cross patterns for advanced control. Enjoy your flight!

Illustrations depict practice maneuvers: Fixed-Point Landing, Square Pattern Maneuver, Cross Pattern Maneuver.

Adjusting the Trim

The ASC-2680 is pre-trimmed. However, after crashes, trim adjustments may be needed for balance:

• Forward/Backward Trim: Use forward/backward trim buttons to counter drift (Diagram M).
• Bank Right/Left Trim: Use left/right trim buttons to counter lateral drift (Diagram N).
• Spinning/Rotating Trim: Use rotational trim buttons to counter spinning (Diagram O).

Diagram M: Shows forward/backward trim buttons.

Diagram N: Shows left/right trim buttons.

Diagram O: Shows rotational trim buttons.

NOTE: Trim buttons produce beeps for each adjustment. A long beep indicates the center position. Maximum trim is reached with no further beeps. If instability persists, resync and recalibrate.

EMERGENCY STOP: Press the "speed setting button" and "stunt button" simultaneously to instantly stop the drone's blades.

Calibrating the ASC-2680

If the drone drifts or fails to hold its center position after crashes, recalibration is needed:

1. Place the ASC-2680 on a very flat and level surface.
2. Ensure the drone is powered on and the controller is synced. Do not start the blades.
3. Move both the throttle and control sticks down and to the right-hand bottom corner (Diagram P).
4. Successful calibration is indicated by the drone's lights flashing rapidly and then stopping.

TROUBLESHOOTING CALIBRATION: If lights do not flash, remove the drone battery, turn off the controller, and restart the process. Ensure the battery is inserted before turning on the controller. Push the left throttle stick up and down until a beep is heard to resync before calibrating.

Diagram P: Shows moving both control sticks down and to the right corner for calibration.

Performing 360° Stunt Rolls

To perform stunt rolls:

1. Hover the ASC-2680 at least 6 feet clear of obstacles. Ensure speed settings are 2 or 3 (not 1 or T Mode).
2. Press the 360 stunt button on the controller (Diagram Q) to enter stunt roll mode (indicated by rapid beeping).
3. Use the right control stick: push right for a right-side roll, or left for a left-side roll (Diagram R). Use caution.

Diagram Q: Points to the 360° Stunt Roll Button.

Diagram R: Illustrates using the right control stick for stunt rolls.

NOTE: To exit stunt mode without flipping, press the stunt button again.

Recording Videos and Taking Photos

The ASC-2680 features an HD camera for video and photos. You can record simultaneously to a mobile device via the ASC-2680 App and to a microSD card for higher definition.

Micro SD Card Recording for Highest Definition Video:

What You'll Need:

• One microSD card reader (included).
• One microSD card (not included).
• A computer with a USB port and media player software.

Formatting Your microSD Card:

Place the microSD card into the USB SD card reader and plug it into your computer's USB port (Diagrams U1, U2). Follow your computer's instructions to format the card.

Diagram U1 & U2: Show a microSD card being inserted into a USB card reader connected to a computer.

Installing the microSD Card in Your ASC-2680 Drone:

Insert the formatted microSD card into the drone's SD card port (Diagram U3) until it clicks. Ensure the drone is powered on and synced.

Diagram U3: Shows the microSD card being inserted into the drone's SD card slot.

Taking Digital Photos: Short press the CAMERA button on the controller. A beep and single flash of drone LEDs indicate a photo taken.

Recording Videos: Press and hold the CAMERA button for 2-3 seconds. A long beep and two flashes of drone LEDs indicate video recording has started. Press the button once to stop recording.

Installing Your Phone Holder

To use the drone's camera features, install the phone holder onto the controller. Attach the top "teeth" into the controller's top holes, then click the bottom into place (Diagram S). To remove, pull from the bottom.

Diagram S: Illustrates attaching the phone holder to the controller.

IMPORTANT NOTICE: Test camera functions before flying.

Removing Your microSD Card

Gently push the SD card in to release it, then pull it out. Store the card safely.

Downloading and Clearing Space on Your microSD Card

Connect the microSD card reader to your computer to download photos and videos. Delete files from the card after downloading.

Camera Video and Photo Streaming Setup

Your ASC-2680 streams video and photos to your mobile device via the ASC-2680 App.

What You Will Need:

• An Apple or Android smartphone (not included).
• The ASC-2680 App installed on your device.

To Download the ASC-2680 App: Scan the provided QR codes or manually enter the web addresses for the Android Play Store or Apple Store. Follow the in-app tutorial for instructions on connecting and using the app.

QR codes are provided for downloading the ASC-2680 App from the Android Play Store and Apple Store.

If you encounter difficulties, contact customer service at 1-866-360-1510.

Troubleshooting Your ASC-2680

Replacing Propeller Blades

Propellers may need replacement after crash landings. Ensure correct blade placement:

• The ASC-2680 has four sets of blades, marked A and B. Match the indication markings on the blades to their correct positions (Diagram T).
• Unscrew and remove the damaged blade.
• Replace with the correct new blade.

Diagram T: Shows propeller blade placement with indication letters A and B for front and rear blades.

General Warnings

The ASC-2680 is for OUTDOOR USE ONLY. Revolving blades can cause damage. Stand clear of the flight path and warn spectators. Inspect rotor blades before flight to ensure they are securely fastened.

• Choking/Cutting Hazard: Small Parts/Sharp Rotor Blades.
• Keep hands, hair, and loose clothing away from propellers when the drone is powered on.
• Turn off the transmitter and drone when not in use.
• Use only the included charger for the ASC-2680 battery.
• New alkaline batteries are recommended for controller performance.
• Parental supervision is recommended when flying the ASC-2680.

Battery Warnings

• Rechargeable Battery: If the battery no longer holds a charge, dispose of it properly according to local regulations.
• Controller Batteries: Requires 4 "AAA" batteries. Always replace all batteries at once. Do not mix battery types (alkaline, carbon-zinc, NiMH) or old and new batteries. Non-rechargeable batteries must not be recharged. Rechargeable batteries require adult supervision. Exhausted batteries must be removed and disposed of properly. Supply terminals must not be short-circuited. Use only recommended battery types and ensure correct polarity. Do not dispose of batteries in fire.

Care and Maintenance

• Remove batteries from the remote control when not in use for extended periods.
• Clean the remote control and ASC-2680 with a clean, damp cloth.
• Keep the product away from direct heat or sunlight.
• Do not submerge the product in water.
• Parental guidance is recommended for battery installation or replacement.

Limited 90-Day Warranty

AMAX Group USA warrants the original consumer that this product is free from electrical or mechanical defects for 90 days from the purchase date. To claim warranty, the unit must be returned postage prepaid and insured, along with the original receipt, to the specified warranty center. The warranty covers normal consumer use and excludes damage from shipment, alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use, or unreasonable use. Removal of parts voids the warranty. Implied warranties are limited to 90 days. Consequential or incidental damages are excluded.

REPAIR/REPLACE PRODUCT: If the product malfunctions, contact the warranty center for an RMA number and return address. AMAX reserves the right to repair, replace, or refund the product.

IMPORTANT NOTICE: Returns without an AMAX-issued RMA form and number will be rejected.

PREPARATION FOR SHIPPING: Repack the product securely, preferably in its original carton. Include the RMA form, daytime phone number, and email address. Ship prepaid and insured.

For inquiries, contact customercare@amaxbrands.com or call 1-866-360-1510.

Regulatory Information

FCC Part 15 C Notice: This equipment complies with Part 15 of the FCC Rules. Operation is subject to two conditions: (1) this device may not cause harmful interference, and (2) it must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, designed to provide reasonable protection against harmful interference in residential installations. It generates, uses, and can radiate radio frequency energy. If it causes harmful interference to radio or television reception, users are encouraged to try correcting it by reorienting the receiving antenna, increasing separation between equipment and receiver, connecting to a different circuit, or consulting a dealer/technician.

This equipment complies with FCC/IC radiation exposure limits for an uncontrolled environment and should be installed and operated with a minimum distance of 20cm between the radiator and your body (for the drone).

ISED NOTICE: CANADA ONLY: This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to two conditions: 1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device.

CAN ICES-003(B) / NMB-003(B): This product meets the applicable Innovation, Science and Economic Development Canada technical specifications.

Safety Warnings

WARNING! CHOKING HAZARD - Small parts. Not suitable for children under 3 years.

Manufacturer & Distributor Information

Costco Wholesale Canada Ltd.
415 W. Hunt Club Road
Ottawa, Ontario K2E 1C5, Canada
www.costco.ca

Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD.
Office No.3, 10/F Witty Commercial Building 1A-1L Tung Choi street, Mongkok.
Kowloon Hongkong
© 2023 All Rights Reserved.

Made in China