ASC-2400 HD Video Drone

Welcome

Thank you for purchasing the ASC-2400 Drone. Please read this instruction booklet as it contains valuable information on how to properly fly and care for your ASC-2400.

Features

• Streams video and still images directly to your mobile device
• Push button Auto Start, Hover, and Auto Land technology
• Built-in 6 Axis Gyro + Altitude Sensors for incredibly stable flight
• High Efficiency Li-poly battery extends drone flight time
• "Go-Anywhere" Folding Frame design for easy transportation

Setup and Installation

Remote Control Battery Installation

1. Unscrew and remove the battery cover from the back of the controller.

2. Install 4 AAA alkaline batteries into the controller. Replace the battery cover and secure it.

3. Turn over the controller front side up and press the power button. If you hear two beeps and the power indicator light turns on, you have installed your batteries correctly.

Charging the ASC-2400 Li-Poly Battery

1. Insert the USB charger into the battery charging socket.

2. Connect the USB end of the cable to your computer's USB port or a USB wall charger.

3. A red LED indicator light will illuminate while charging and then turn off when charging is complete.

4. Average charging time is approximately 130-150 minutes (via 5.0V-2A USB wall charger). A fully charged ASC-2400 can fly for 15-18 minutes depending on environment and user input.

IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

Installing the ASC-2400 Battery

Carefully push the fully charged battery into the ASC-2400 battery compartment all the way in until it stops and is flush with the back of the drone. Note: The battery only fits one way into the battery compartment. Never force it.

Expanding and Folding Your ASC-2400 Arms

Before flying your ASC-2400, you need to expand the foldable arms out.

1. Make sure the drone power is turned off.

2. Holding the folded ASC-2400 drone, proceed to open the arms by starting with the Front Arms (Upper Arms) and then Rear Arms (Lower Arms).

3. Make sure the arms are fully extended and locked into place. You will feel some additional pressure indicating the arm is properly locked.

4. When folding in the arms, simply reverse steps 1-3.

NOTE: Never use hard force when opening and closing the ASC-2400 Arms.

Drone and Controller Overview

ASC-2400 Diagram

The ASC-2400 drone features a camera at the front, propellers on each of the four arms, and a power button.

Controller Diagram

The controller includes:

• Direction Controls: Left stick for Throttle/Yaw (Up/Down for ascent/descent, Left/Right for rotation), Right stick for Direction (Forward/Backward for forward/backward movement, Left/Right for banking left/right).
• Trim Controls: Forward/Backward Trim, Bank Right/Left Trim, Spinning/Rotating Trim buttons.
• Function Buttons: Emergency Stop, Speed Setting Button, 360° Stunt Rolls Button, AUTO Start/AUTO Land button.
• Other Indicators: ON/OFF & Power Indicator.
• Camera Controls: Press to take a photo, Press down & hold to begin video recording.

Flight Preparation and Syncing

Flight Preparation

WARNING: DO NOT FLY YOUR ASC-2400 IN FOUL WEATHER!

Verify that there are 4 "AAA" batteries inside the remote control unit and the ASC-2400 Li-poly battery has been fully charged.

Make sure to be in a large open space, preferably a field or park with an open radius of at least 400 feet.

Ensure the drone is started on a clean, flat, level surface before take-off.

IMPORTANT: Until you have experience, it is not advised to fly in any wind. Pick a day with zero or extremely light wind conditions when learning.

Syncing Your ASC-2400

Important! When syncing, ensure the drone is on a flat level surface and digital trim settings are centered.

1. Before starting, ensure the controller power is off and the ASC-2400 battery is removed.

2. Insert the battery into the ASC-2400, place it on a flat level surface, and press and hold the power button for a few seconds. The drone's red LED lights should flash rapidly, then slowly.

3. Quickly turn ON the remote. The controller's top red LED light will flash.

4. Push the throttle stick all the way up, then pull it all the way down. You should hear a high-pitched beep both ways. If the drone and controller indicator lights stop flashing and stay solid, syncing is successful.

If syncing fails, repeat steps 1-4.

TIP 1: Minimize the time between turning the drone on and the controller on to avoid timing out.

TIP 2: Syncing indoors or in shade makes LED indicators easier to see.

Flying the Drone

Now You Are Ready to Fly!

Once synced, familiarize yourself with starting/stopping rotors, auto-land, and controls. Practice in a large open field with light wind.

Recognizing the Front & Rear of the ASC-2400

The front of the drone is the side with the camera. The rear is the side with a red light.

Starting & Stopping the Rotors

You can start and stop rotors manually or automatically.

Auto Start/Auto Land: Press the auto START/LAND button on the controller to take off or land automatically. You can still control direction during auto-landing.

Manual Start/Stop:

• To Start: Move both control sticks simultaneously down to the inside or outside corners, hold until rotors spin, then release to neutral and push throttle up to take off.
• To Stop: Land the drone, and rotors stop automatically within ten seconds. Alternatively, move both control sticks simultaneously down and to the inside or outside bottom corners.
• EMERGENCY STOP: Press the SPEED button and STUNT button simultaneously.

Speed Select Button

The ASC-2400 has 3 speed settings: 1 (SLOW), 2 (MEDIUM), and 3 (HIGH). The default is SLOW. Press the speed setting button to cycle through speeds, indicated by beeps. Settings can be adjusted before or during flight.

Flight Control Inputs

Use the left throttle stick for ascent, descent, and rotation (left/right). Use the right direction control stick for forward/backward movement and banking (left/right).

Ascend/Descend: Move left throttle stick up/down.

Rotate Left/Right: Move left throttle stick left/right.

Move Forward/Backward: Move right direction control stick forward/backward.

Bank Left/Right: Move right direction control stick left/right.

Flight Practice

Practice simple maneuvers like vertical takeoffs, landings, and turns. Progress to square and cross patterns for advanced control.

Advanced Operations

Adjusting the Trim

The ASC-2400 is pre-trimmed, but adjustments may be needed after crashes.

Use the trim buttons to counteract drifting:

• Forward/Backward Trim: Counter forward/backward drift.
• Bank Right/Left Trim: Counter left/right drift.
• Spinning/Rotating Trim: Counter unwanted rotation.

A short beep indicates one trim position movement. A long beep indicates the center trim position. No beeps mean maximum trim is reached.

If the drone remains unstable, re-sync and recalibrate.

Calibrating the ASC-2400

Recalibration may be needed if the drone drifts or cannot hold its center position after shocks.

1. Place the ASC-2400 on a very flat level surface.

2. Ensure the drone is on and the controller is synced. Do not start the blades.

3. Move both throttle and control sticks down and to the bottom right corner. The drone's lights should flash and then stop, indicating successful calibration.

Troubleshooting Calibration: If lights don't flash, remove the drone battery, turn off the controller, and restart. Re-sync the drone by moving the left throttle stick up and down until you hear a beep.

Performing 360° Stunt Rolls

1. Hover the ASC-2400 at least 6 feet clear above and below. Set speed to mode 2 or 3 (not possible in mode 1).

2. Press the 360 stunt button on the controller to enter stunt roll mode (indicated by rapid beeping).

3. Use the right control stick: push directly right for a right-side roll, or directly left for a left-side roll.

NOTE: To exit stunt mode without flipping, press the stunt button again.

Camera and App Integration

Installing Your Phone Holder

To use the drone's camera, install the phone holder by clicking the top teeth into the controller's top holes, then securing the bottom. To remove, pull from the bottom first.

Camera Video and Photo Streaming Setup

The ASC-2400 has an on-board camera for video and photo streaming.

What You Need:

• An Apple or Android smartphone (not included).
• The ASC-2400 App installed on your device.

To Download the ASC-2400 App: Scan the QR codes below or manually enter the web addresses.

• For Apple iOS: [QR code for iOS app download] http://netopsun.com/asc_2000_series_apple (Requires iOS 10.0 or higher)
• For Android OS: [QR code for Android app download] http://netopsun.com/asc_2000_series_google (Requires OS 4.2.2 or higher)

After installation, click the ASC-2400 App icon to run it. Follow the in-app "TUTORIAL" for connecting the drone and using the app for recording.

If you encounter difficulties, contact customer service at www.amaxbrands.com or 1-866-360-1510.

Troubleshooting

Troubleshooting Your ASC-2400

Replacing the Propeller Blades

Propeller system may need repair/replacement due to crash damage.

1. The ASC-2400 has four sets of blades: two with letters A & B on the front, and two with B & A on the rear.

2. Match the indication markings/letters on the blades when replacing.

3. Unscrew and remove the damaged blade.

4. Replace with the new, correct blade.

Blade Identification: Front Left = A, Front Right = B, Back Left = B, Back Right = A.

Warnings, Maintenance, and Warranty

ASC-2400 Warnings

The ASC-2400 is designed for OUTDOOR USE ONLY. Blades revolve at high speeds and can cause damage. Stand away from the flight path and warn spectators.

WARNING!

• Choking/Cutting Hazard: Small Parts/Sharp Rotor Blades.
• Keep hands, hair, and loose clothing away from propellers when the drone is ON.
• Turn off the transmitter and drone when not in use.
• Use the included charger specifically for the ASC-2400 Li-Poly battery.
• New alkaline batteries are recommended for maximum performance.
• Parental supervision is recommended when flying.

Battery Warnings

Rechargeable Battery: If the Li-Poly battery no longer holds a charge, dispose of it properly according to local requirements.

Controller Batteries: Requires 4 "AAA" batteries.

• Always replace the whole set of batteries at one time.
• Do not mix battery types (alkaline, carbon-zinc, NiMH) or old/new batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries must be removed before charging (if removable) and charged under adult supervision.
• Exhausted batteries must be removed immediately and recycled/disposed of properly.
• Supply terminals must not be short-circuited.
• Use only batteries of the same or equivalent type.
• Insert batteries with correct polarity.
• Do not dispose of batteries in fire; they may leak or explode.
• Connect only to equipment with symbols: [power symbol] or [recycle symbol].

Care and Maintenance

• Always remove batteries from the remote control when not in use for extended periods.
• Gently wipe the remote and drone with a clean damp cloth.
• Keep the product away from direct heat or sunlight.
• Do not submerge the product in water.
• Parental guidance recommended for battery installation/replacement.

Limited 90-Day Warranty (North America)

AMAX Group USA warrants the product to be free from electrical or mechanical defects for 90 DAYS from the date of purchase. To claim warranty, the unit must be returned postage prepaid and insured, along with the original receipt from an approved AMAX retail partner.

The warranty covers normal consumer use and excludes damage from shipment, alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use, or unreasonable use. Removal of parts voids warranty. This warranty does not cover third-party repair costs.

Implied warranties (merchantability, fitness) are limited to 90 DAYS. Consequential or incidental damages are excluded. Some states may not allow these limitations.

Repair/Replace Product

If the product malfunctions, contact the warranty center. A return authorization (RMA) number and address will be provided if a return is necessary. AMAX reserves the right to repair, replace, or refund.

IMPORTANT NOTICE: Returns without an AMAX issued RMA form/number will be rejected.

Preparation for Shipping: Repack in a durable box (original carton preferred), ship prepaid and insured. Include the RMA form, daytime telephone number, and email address.

For service after warranty expiration, contact customer care at customercare@amaxbrands.com.

Australian Consumer Law guarantees apply where relevant.

IMPORTANT NOTICE! DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:

www.amaxbrands.com

Email: care@amaxglobal.com

Phone: 1-866-360-1510

Legal and Compliance

FCC Part 15 C Notice

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Statements (for the drone only)

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment.

This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.

Product Information

Model: ASC-2400 HD VIDEO DRONE

Camera: ON BOARD HD CAMERA, 1280 x 720 pixels, 25 frames per second

Conforms to safety requirements of FCC.

Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD.

AMAX Group USA Address: 12645 Memorial Dr Suite F1 #388 Houston, TX 77024

© 2021 All Rights Reserved. Visit us at www.amaxbrands.com

Distributed by: Costco Wholesale Corporation, P.O. Box 34535, Seattle, WA 98124-1535, USA. 1-800-774-2678, www.costco.com

WARNING! CHOKING HAZARD - Small parts. Not suitable for children under 3 years.

Made in China CT-6333 C009-USA-V1.0

Package Contains:

• ASC-2400 Drone
• 2.4G Wireless Controller
• Spare Parts
• USB Charger
• Phone Holder
• Battery Set of 4 AAA Batteries for Controller
• Instruction Manual

Colors and styles may vary slightly from photos.