Ascend Aeronautics ASC-2080 Compact HD Video Drone

Safety and Regulatory Information

FCC Part 15 C Notice

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ? Reorient or relocate the receiving antenna. ? Increase the separation between the equipment and receiver. ? Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ? Consult the dealer or experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF Exposure Statements

This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.

Product Overview

Features

• Compact fold-in design for easy portability.
• New obstacle avoidance training feature automatically circumvents obstructions for new pilots.
• Air pressure sensor locks flight altitude for stable video footage.
• Captures video and still shots with onboard HD Camera (1280 x 720 pixels at 25 frames per second).
• 6-axis gyro for extremely stable flight and maneuverability.

WARNING: CHOKING HAZARD - Small parts. Not suitable for children under 3 years.

Requires Speed Class 10 or higher microSD or microSDHC card (not included). microSDHC Logo is a trademark of SD-3C, LLC.

Package Contents

• ASC-2080 Drone
• 2.4G Wireless Controller
• Spare Parts
• USB Charger
• Phone Holder
• Battery
• Instruction Manual

Colors and styles may vary slightly from photos.

Setup and Preparation

Remote Control Battery Installation

1. Unscrew and remove the battery cover from the back of the controller.

2. Install 3 fresh "AAA" alkaline batteries into the controller as shown in Diagram A. Replace the battery cover and secure it.

3. Turn over the controller and press the power button. If the power indicator turns on, batteries are installed correctly.

Diagram A Description: Shows the remote control's battery compartment with indicators for three "AAA" batteries to be inserted.

Charging the ASC-2080 Li-Poly Battery

1. Connect the USB charger to the battery charging socket (see Diagram B).

2. Connect the USB end of the cable to your computer's USB port or a USB wall charger (see Diagram C).

3. The indicator light on the USB charger will turn solid red while charging. It turns off when charging is complete.

4. Average charging time is approximately 60-80 minutes (using a 5.0V 2A USB wall charger).

IMPORTANT: ALWAYS UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

Diagram B Description: Shows the Li-Poly battery with the USB charger cable connected to its charging port.

Diagram C Description: Shows the USB end of the charging cable plugged into a computer's USB port.

Installing the ASC-2080 Battery

Carefully push the fully charged battery into the ASC-2080 battery compartment until it stops and is flush with the back of the drone (see Diagram D). The battery only fits one way; do not force it.

Diagram D Description: Illustrates the Li-Poly battery being fully inserted into the drone's battery compartment.

Expanding and Folding Your ASC-2080 Arms

Before flying, expand the foldable arms.

1. Ensure the drone power is turned off.

2. Hold the folded drone (see Diagram E) and unfold the arms, starting with the Rear Arms (Lower Arms) then the Front Arms (Upper Arms).

3. Ensure arms are fully extended and locked into place (see Diagram F). You will feel additional pressure indicating a proper lock.

4. To fold, reverse steps 1-3.

NOTE: Never use excessive force when opening or closing the arms.

Diagram E Description: Shows how to hold the folded drone and begin unfolding the arms, starting with the rear ones.

Diagram F Description: Depicts the drone with its arms fully extended and locked. Also shows the throttle stick movement for syncing.

Diagrams

ASC-2080 Diagram

Diagram Description: The ASC-2080 drone is shown with its main components labeled: Propeller, Camera, Li-Poly Battery, Safety Guard.

Controller Diagram

Diagram Description: The 2.4G Wireless Controller is shown with buttons and sticks labeled: Power Button, Speed Setting Button, 360° Stunt Rolls Button, AUTO Start/Land Button, Power Indicator ON/OFF Switch, Throttle Stick (Up/Down), Yaw (Left/Right Rotation), Forward Trim, Backward Trim, Banking Right Trim, Banking Left Trim, Direction Controls (Forward/Backward/Left/Right), Press to take a photo, Press down & hold to begin video recording.

Flight Preparation

• Verify 3 "AAA" batteries in the remote and the ASC-2080 battery is fully charged.
• Be in a large open space, preferably a field or park with at least 200 feet radius.
• Start the drone on a clean, flat, level surface before take-off.
• IMPORTANT: As a beginner, avoid flying in windy conditions. Pick a day with zero or very light wind.

Syncing Your ASC-2080

Important: Always sync on a flat, level surface with digital trim settings centered.

1. Ensure the controller power is OFF and the ASC-2080 battery is removed.
2. Insert the ASC-2080 battery, place it on a flat surface, and press and hold the power button for a few seconds (see Diagram F). The drone's LED lights will flash.
3. Quickly turn ON the remote controller. The top red LED light on the controller will flash.
4. Push the throttle stick all the way up until it stops, then pull it all the way down to the bottom (see Diagram F). You should hear a high-pitched beep each way.
5. If the indicator lights on the drone and controller stop flashing and become solid, you have successfully synced. Repeat steps 1-4 if syncing fails.

TIP 1: Sync quickly after turning on the drone to avoid a timeout.

TIP 2: Syncing indoors or in shade helps visibility of LED indicators.

Diagram F Description (Syncing): Shows the throttle stick movement (up and down) required for syncing. The drone's LED lights change from flashing to solid upon successful sync.

Flying Your Drone

Once synced, you are ready to fly. Familiarize yourself with starting/stopping rotors, auto-land, and control features. Practice in a large, open area on a day with minimal wind. Do not fly too high until experienced.

Recognizing the Front & Rear of the ASC-2080

The front of the ASC-2080 is the side with the camera. The rear is the side with the red light (see Diagram G).

Diagram G Description: Illustrates the drone, indicating the front (camera) and rear (red light) sides.

Automatically Take Off / Land

Ensure the ASC-2080 is synced.

• Press the Auto Start/Land button; the drone will take off automatically (see Diagram H1).
• Press the Auto Start/Land button again to land the drone automatically (see Diagram H1).

Tips: You can also start rotors by moving both control sticks simultaneously down inside or outside corners, then push the throttle stick slowly to take off manually (see Diagram H2).

Diagram H1 Description: Shows a finger pressing the "Auto Start/Land" button on the controller.

Diagram H2 Description: Illustrates the manual takeoff procedure using both control sticks.

Speed Select Button

The ASC-2080 has 4 speed settings: T (Training), 1 (SLOW), 2 (MEDIUM), and 3 (HIGH). The default is 1 (SLOW). Press the speed setting button to increase speed; beeps indicate the current setting.

T (Training) Mode & Obstacle Avoidance Training Feature

Press and hold the Speed Button for 2 seconds to enter T Mode (indicated by a long beep). T Mode operates at a very slow speed with maximum and minimum height limits. The obstacle avoidance feature works only in T Mode, causing the drone to automatically circumvent obstructions.

Flight Control

Master basic flight functions in a large, open space with the drone facing away from you. Practice makes perfect!

• Ascend/Descend: Move the left throttle stick up to ascend, down to descend (see Diagram I).
• Rotate: Move the left throttle stick left to rotate counter-clockwise, right to rotate clockwise (see Diagram J).
• Forward/Backward: Move the right direction control stick forward to move forward, backward to move backward (see Diagram K).
• Banking: Move the right direction control stick left to bank left, right to bank right (see Diagram L).

Diagram I Description: Shows the left throttle stick controlling vertical movement (up for ascend, down for descend).

Diagram J Description: Shows the left throttle stick controlling horizontal rotation (left for counter-clockwise, right for clockwise).

Diagram K Description: Shows the right direction control stick controlling forward and backward movement.

Diagram L Description: Shows the right direction control stick controlling banking left and right.

Flight Practice

Practice basic exercises like vertical takeoffs, landings, and turns. Progress to square and cross pattern maneuvers.

Diagram Description: Visual representations of flight practice maneuvers: Fixed-Point Landing, Square Pattern Maneuver, Cross Pattern Maneuver.

Adjusting the Trim

The ASC-2080 is pre-trimmed and calibrated. Trim adjustments may be needed after crashes.

• Forward/Backward Trim: Use forward/backward trim buttons to counter drifting (see Diagram M).
• Banking Left/Right Trim: Use left/right trim buttons to counter drifting (see Diagram N).

NOTE: A single long beep indicates the center trim. No sound means maximum trim on that side.

Diagram M Description: Highlights the forward/backward trim buttons on the controller.

Diagram N Description: Highlights the left/right trim buttons on the controller.

Calibrating the ASC-2080

Recalibration may be needed if the drone drifts or hovers unstably after crashes.

1. Place the ASC-2080 on a flat, level surface.
2. Ensure the drone is powered on and synced to the controller (refer to Syncing). Do not start the blades.
3. Move both the throttle and control sticks down and to the right corner (see Diagram R).
4. The drone's lights will rapidly flash and then stop, indicating calibration is complete.

TROUBLESHOOTING: If lights don't flash, remove the drone battery, turn off the controller, and restart. Ensure the battery is inserted before turning on the controller. Push the left throttle stick up and down to re-sync if needed.

Diagram R Description: Shows both control sticks moved to the bottom-right corner to initiate calibration.

About 360° Stunt Flips

Execute 360° stunts once confident in control. Remove blade guards for best performance. Operate in a large, open area. Stunts consume battery power, reducing flight time. When battery is low, flip mode is disabled.

Steps to Executing a Stunt Flip

1. Hover the ASC-2080 with at least 5 feet of clearance. Set speed to Mode 2 or 3 (T Mode and Speed 1 do not support flips).
2. Press the 360 stunt button (Diagram S) to enter "stunt roll mode" (indicated by rapid beeping).
3. Use the right control stick: push right for a "right side roll" or left for a "left side roll" (see Diagram T). Use caution.

NOTE: To exit stunt roll mode without flipping, press the stunt button again.

Diagram S Description: Highlights the 360° Stunt Rolls button on the controller.

Diagram T Description: Shows the right control stick being used to perform a stunt flip (right or left).

Recording Videos and Taking Photos

The ASC-2080 has an onboard HD camera for video and still photos. You can record simultaneously to a mobile device (via app) and a microSD card (highest definition).

What You Will Need to Record on a microSD Card

• One microSD card reader (included).
• One microSD card (not included).
• A computer with a USB port and media player software.

Formatting Your microSD Card

1. Insert the microSD card into the USB SD card reader and plug it into your computer (see Diagrams U1 and U2).

2. Right-click the card's icon on your Desktop and follow instructions to format.

Diagram U1 Description: Shows a microSD card being inserted into a USB card reader.

Diagram U2 Description: Shows the USB card reader plugged into a computer's USB port.

Installing the microSD Card in Your ASC-2080 Drone

1. Insert the formatted microSD card into the ASC-2080 SD card port (see Diagram U3). Push gently until it clicks.

2. Turn on the ASC-2080 and ensure it is charged and synced.

Diagram U3 Description: Shows the microSD card being inserted into the drone's SD card port, noting the correct orientation.

Taking Digital Photos

Short press the CAMERA button on the controller. A "beep" and a single flash of the drone's red and white LEDs indicate a photo has been taken.

Recording Videos

Long press the CAMERA button for 2-3 seconds. Two "beeps" and rapid flashing of the drone's LEDs indicate video recording has started. Press the button again to stop recording.

Installing Your Phone Holder

Attach the phone holder to the back of the controller by clicking the top two teeth into the top holes, then the bottom (see Diagram U4). Pull from the bottom to remove.

Diagram U4 Description: Illustrates attaching the phone holder to the controller.

Removing Your microSD Card

Push in gently on the back of the SD card until it clicks and pops out slightly. Remove by pulling gently.

Downloading and Clearing Space on Your microSD Card

Plug the microSD card into the reader and connect to your computer. Download all content to your computer. After downloading, delete files from the microSD card using your computer's instructions.

Camera Video and Photo Streaming Setup

The ASC-2080 streams video and photos to your mobile device.

What You Will Need to Get Started

• One Apple or Android smartphone (not included).
• The ASC-2080 App downloaded and installed.
• Scan the QR codes or manually enter the web addresses to download the app from the Android Play Store or Apple Store.
• Follow the "TUTORIAL" within the app for connecting/pairing the drone and using camera functions.

QR Code Description: Placeholder for QR codes linking to the ASC-2080 App on the Apple App Store and Google Play Store. The text indicates manual URLs: Apple iOS http://qr03.cn/Bn4HaO, Android OS http://qr03.cn/FqBpEP.

Note: Apple devices require iOS 10.0+; Android devices require OS 4.2.2+.

If difficulties persist, contact customer service at www.amaxbrands.com.

Troubleshooting Your ASC-2080

Replacing the Propeller Blades

The propeller system may need repair/replacement after high-speed crashes.

1. The ASC-2080 has four sets of blades: A & B on the front, B & A on the rear (see Diagram V).

2. Match the indication markings (A or B) on the blades when replacing.

3. Unscrew and remove the damaged blade.

4. Replace with the correct new blade.

Diagram V Description: Illustrates the drone's propellers with labels A and B, specifying which blade type corresponds to each position (Front Left=A, Front Right=B, Back Left=B, Back Right=A).

Blade Guard Installation

Blade guards are recommended for beginners for safety. Attach the 4 blade guards to each landing gear (see Diagram W).

Diagram W Description: Shows the blade guards being attached to the drone's landing gear.

Warnings

General Warnings

• WARNING: The ASC-2080 is for INDOOR & OUTDOOR use. Blades revolve at high speeds and can cause damage. Stand away from the drone. Warn spectators. Inspect rotor blades before flight.
• WARNING! Choking/Cutting Hazard: Small Parts/Sharp Rotor Blades.
• Keep hands, hair, and loose clothing away from propellers when power is ON.
• Turn off the transmitter and drone when not in use.
• Use only the included charger for the Li-Poly battery. Do not use for other batteries.
• New alkaline batteries are recommended for maximum performance.
• Parental supervision is recommended.

Battery Warnings

• RECHARGEABLE BATTERY: This ASC-2080 uses a Li-Poly rechargeable battery. Dispose of properly if it no longer holds a charge.
• CONTROLLER BATTERIES: Requires 3 "AAA" batteries (not included). Follow battery safety warnings:
  • Do not mix battery types (alkaline, carbon-zinc, rechargeable).
  • Do not mix old and new batteries.
  • Non-rechargeable batteries are not to be recharged.
  • Remove rechargeable batteries before charging.
  • Charge rechargeable batteries under adult supervision.
  • Remove exhausted batteries immediately and recycle/dispose of properly.
  • Do not short-circuit supply terminals.
  • Use only recommended battery types.
  • Insert batteries with correct polarity.
  • Do not dispose of batteries in fire; they may leak or explode.

Care and Maintenance

• Remove batteries from the remote control if not used for an extended period.
• Clean with a clean, damp cloth.
• Keep away from direct heat or sunlight.
• Do not submerge the toy in water.
• Parental guidance recommended for battery installation/replacement.

Warranty Information

Limited 90-Day Warranty (North America)

AMAX Group USA warrants the original consumer that this product is free from electrical or mechanical defects for 90 DAYS from the date of purchase. If a defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt of the unit, shipped postage prepaid and insured to their warranty center, along with the original receipt. The warranty covers normal consumer use and does not cover damage from shipment, alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use, or unreasonable use. Removal of parts voids all warranties. This warranty does not cover repairs made or attempted by third parties. Implied warranties are limited to 90 DAYS. Consequential or incidental damages are excluded. Some states may not allow these limitations.

Repair/Replace Product

If the product malfunctions, contact the warranty center. If a return is necessary, an RMA number/form and return address will be issued. AMAX reserves the right to repair, replace, or refund the product.

IMPORTANT NOTICE: Returns without an AMAX issued RMA form and number will be rejected. Contact the warranty center before returning.

Preparation for Shipping Your Product

Repack the product in a durable box, preferably the original carton. Send prepaid and insured. Include the RMA form, your daytime telephone number, and email address inside the carton. For expired warranties or service inquiries, contact customer care.

IMPORTANT NOTICE! DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:

www.amaxbrands.com Email: customercare@amaxbrands.com