ASC-2680 Premium HD Video Drone

Introduction

Thank you for purchasing the ASC-2680 Drone. This instruction booklet contains valuable information on how to properly fly and care for your ASC-2680. Please read it carefully before operation.

FCC Part 15 C Notice

⚠️ CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

FCC RF exposure statements: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body or nearby persons.

Product Overview

Model: ASC-2680

Description: PREMIUM HD VIDEO DRONE WITH ULTRA-WIDE LENS AND OPTICAL FLOW TECHNOLOGY

On Board HD Camera: 1920 x 1080 pixels, 25 frames per second.

❗ WARNING! CHOKING HAZARD - Small parts. Not suitable for children under 3 years.

Requires Speed Class 10 or higher microSD or microSDHC card (not included). microSDHC Logo is a trademark of SD-3C, LLC.

Conforms to safety requirements of FCC.

Distributed by: TRACTOR SUPPLY COMPANY, 5401 VIRGINIA WAY, BRENTWOOD, TN 37027. For customer support, call: 1-888-376-9601. Website: www.TractorSupply.com

Manufacturer/Brand: Ascend Aeronautics™ is the registered trademark of AMAX Industrial Group LTD. Office No.3, 10/F Witty Commercial Building, 1A-1L Tung Choi street, Mongkok, Kowloon, Hongkong. © 2024 All Rights Reserved. Visit us at www.amaxbrands.com

Made in: China

Document Version: C012-USA-V1.0

Package Contents

• ASC-2680 Drone
• 2.4G Wireless Controller
• Spare Parts
• USB Charger
• Phone Holder
• Battery
• micro SD Card Reader

Note: Colors and styles may vary slightly from photos.

Features

• Ultra-Wide angle lens provides greater aerial video and photography coverage.
• 1080p HD camera streams directly to your mobile phone for instant video recording.
• On-board micro SD card recording for highest resolution video.
• New Optical Flow Technology for longitude and latitude position holding.
• New Flight Training Mode and Range Warning for beginner pilots.
• Push button Auto Start, Hover, and Auto Land technology.
• Built-in 6-axis gyro + altitude sensors for incredibly stable flight.
• High-efficiency Li-Poly rechargeable battery extends drone flight time.
• "Go-Anywhere" folding frame designed for easy transportation.

Setup and Preparation

Remote Control Battery Installation

1. [Unscrew] and remove the battery cover from the back of the controller.

2. [Install] 4 AAA alkaline batteries (not included) into the controller as shown in Diagram A.

Diagram A: Shows the placement of 4 AAA batteries inside the controller.

3. Replace the battery cover and [secure] it.

4. Turn the controller front side up and [press] the power button. If you hear a [beep] and the power indicator light turns on, batteries are installed correctly.

Charging The ASC-2680 Rechargeable Battery

1. [Insert] the USB charger into the battery charging socket (see Diagram B).

Diagram B: Illustrates the USB charger cable being inserted into the drone's battery charging socket.

2. [Connect] the USB end of the cable to your computer's USB port or a USB wall charger (see Diagram C).

Diagram C: Shows the USB end of the charging cable connected to a computer's USB port or a wall adapter.

3. A red LED indicator light will illuminate while charging and turn green when charging is complete.

4. Average charging time is approximately 130-150 minutes (via 5.0V 2A USB wall charger). A fully charged ASC-2680 can fly for 15-18 minutes depending on environment and user input.

❗ IMPORTANT: ALWAYS REMEMBER TO UNPLUG YOUR CHARGING CORD WHEN NOT IN USE!

Installing The ASC-2680 Battery

Carefully [push] the fully charged battery into the ASC-2680 battery compartment all the way in until it stops and is flush with the back of the drone (see Diagram D).

Diagram D: Depicts the ASC-2680 rechargeable battery being inserted into the drone's battery compartment until flush.

NOTE: The battery only fits one way into the battery compartment. Never force it.

How To Expand And Fold Your ASC-2680 Arms

Before flying, you need to expand the foldable arms.

1. Make sure the drone power is turned off.

2. [Hold] the folded ASC-2680 drone in your hand (see Diagram E) and proceed to [open] the arms, starting with the Front Arms and then Rear Arms.

Diagram E: Shows the drone held in hand with arms folded, indicating the starting point for expansion.

3. Make sure the arms are fully extended and locked into place (see Diagram F). You will feel additional pressure indicating the arm is properly locked.

Diagram F: Illustrates the drone arms fully extended and locked into place.

4. When folding, simply [reverse] steps 1-3.

NOTE: Never use excessive force when opening and closing the ASC-2680 Arms.

Diagrams

ASC-2680 Drone Diagram

Key components of the ASC-2680 drone include:

• Camera
• Propeller
• Power Button

Controller Diagram

Key components of the 2.4G Wireless Controller include:

• ON/OFF & Power Indicator
• Throttle/Yaw Control Stick (Left)
• Direction Controls Stick (Right)
• AUTO Start/AUTO Land Button (✈️)
• Speed Setting Button (⚡)
• 360° Stunt Rolls Button (?)
• Emergency Stop (Press Speed + Stunt buttons)
• Trim Controls (Forward/Backward, Left/Right, Spinning)
• Camera Button (? - Press to take photo, Press and hold to begin video recording)

Flight Preparation

• [Verify] that there are 4 "AAA" batteries inside the remote control unit and the ASC-2680 rechargeable battery has been fully charged.
• Be in a large open space, preferably a field or park with an open radius of at least 400 feet.
• Start your drone on a clean, flat, level surface before take-off.
• IMPORTANT! Until you have experience, it is not advised to fly in any wind. Pick a day with zero or extremely light wind conditions when learning.

Syncing Your ASC-2680

Important!

When syncing, always ensure the drone is on a flat level surface and digital trim settings are centered.

1. Before starting, ensure the controller power is off and the battery is removed from the ASC-2680.

2. [Insert] the battery into the ASC-2680 and set it on a flat level surface. [Press] and [hold] the power button for a few seconds (see Diagram G). The LED lights on the drone should begin to flash rapidly.

Diagram G: Shows the drone power button being pressed and the throttle stick moved fully up and then down, with an indicator light turning solid upon successful sync.

3. Quickly turn ON the remote. The top red LED light on the controller face will be flashing.

4. [Push] the throttle stick all the way up until it stops, then [pull] it back all the way down to the bottom. You should hear a high-pitched [beep] both ways. If the indicator lights on the drone and controller stop flashing and stay solid, you have successfully synced.

If you are not able to sync, repeat steps 1-4.

Special Notes During Flight

• Try not to leave too much time between turning your drone on and turning on the controller, or your syncing window will time-out.
• Syncing indoors or in shade makes LED indicators easier to see.
• During flight, the remote control will emit a [beep] if the drone is too far away. Fly the drone closer immediately to avoid signal loss.
• If the remote controller's alarm beeps and the drone continues to fly away, the drone will autonomously initiate a gradual descent to the ground where the signal was lost. The blue LED lights on the drone body will flash until the battery depletes. This helps prevent damage and aids in locating the drone.
• If the drone's relative altitude exceeds 50 feet, the remote controller will emit 5 rapid beeps to remind the operator. High winds at higher altitudes can lead to loss of control. It is recommended to avoid flying at altitudes exceeding 50-60 feet.

Flying Your ASC-2680

If you have successfully synced your ASC-2680, you are ready to fly. Familiarize yourself with starting/stopping rotors, auto-land, and control functions. As a beginner, learn in a large open field with zero or very light wind. Do not try to fly too high until you are experienced.

Recognizing The Front & Rear Of The ASC-2680

The front, or "forward" facing direction, is the side with the camera. The rear, or backward facing direction, is the side with a red light (see Diagram H).

Diagram H: Identifies the front of the drone as the side with the camera, and the rear as the side with the red light.

Starting & Stopping The Rotors

Ensure the ASC-2680 is synced (solid red light on controller and drone).

Auto Start / Auto Land

Press the AUTO START/LAND button (✈️) on the controller (see Diagram I). The ASC-2680 will begin taking off or landing.

Diagram I: Points to the AUTO START/LAND button on the controller.

NOTE: You can still control the drone's direction during auto ascent/landing to avoid obstacles.

Manual Start/Stop

• To Manually start: [Move] both control sticks simultaneously down to the inside or outside corners (see Diagram J), [hold] until rotors spin. Release sticks to neutral, then [push] throttle up to take off.

Diagram J: Shows the simultaneous movement of both control sticks to the bottom corners (inside or outside) to start/stop rotors manually.

• To manually stop:
  1. Land the drone; rotors will stop automatically in under ten seconds.
  2. Immediately stop rotors by moving both control sticks simultaneously down and to the inside or outside bottom corners (see Diagram J).
  3. EMERGENCY STOP: [Depress] both the SPEED button and the STUNT button simultaneously (see Diagram K).

Diagram K: Indicates pressing the SPEED button and STUNT button simultaneously for an emergency stop.

Speed Select Button

The ASC-2680 has 4 speed settings: T (Training MODE), 1 (SLOW), 2 (MEDIUM), and 3 (HIGH). The default is 1 (SLOW). [Press] the speed setting button (⚡) to cycle through speeds. You will hear [beeps] indicating the current speed. Settings can be changed before or during flight.

T (Training) MODE

[Press] and [hold] the Speed Setting Button until a long [beep] is heard. The arm lights will start flashing slowly. T Mode operates at a very slow speed with minimum and maximum height limits to help beginners avoid crashes. To exit T Mode, short [press] the speed setting button again.

Advanced Flight Features

Range Warning

When the ASC-2680's altitude exceeds 50 feet, the remote emits 5 rapid beeps. Before signal loss, the remote emits a continuous rapid warning sound, and the drone's body flashes blue strobe lights. Fly the drone closer. If signal is lost, the drone enters a slow descent and lands automatically. Blue strobe lights flash until battery depletion or restart. This helps prevent damage and aids location.

Optical Flow

The ASC-2680's Optical Flow technology uses a downward-facing camera to analyze the ground image in real-time. Its control system algorithms keep the drone stationary, regardless of wind or drift factors. This feature is functional only at altitudes below 30 feet.

Flight Control

Familiarize yourself with basic flight inputs. Start in a large space with the drone facing away from you. Practice makes perfect!

• Ascend/Descend: [Move] the left throttle stick up to increase propeller speed and ascend. [Move] it down to decrease speed and descend (see Diagram L).

Diagram L: Illustrates moving the left throttle stick up to ascend and down to descend.

• Yaw (Rotate): While in the air, [move] the left throttle stick directly left to rotate counter-clockwise, or directly right to rotate clockwise (see Diagram L1).

Diagram L1: Shows moving the left throttle stick left or right to rotate the drone horizontally.

• Forward/Backward: While in the air, [move] the right direction control stick forward to move forward, or backward to move backward (see Diagram L2).

Diagram L2: Depicts moving the right direction control stick forward or backward to move the drone forward or backward.

• Lateral Movement (Bank): While in the air, [move] the right direction control stick left to bank/sweep left, or right to bank/sweep right (see Diagram L3).

Diagram L3: Shows moving the right direction control stick left or right to bank the drone left or right.

Flight Practice

To master flying, practice exercises like vertical takeoffs, landings, and turns. Once mastered, move to square and cross patterns.

• Fixed-Point Landing
• Square Pattern Maneuver
• Cross Pattern Maneuver

Adjusting The Trim

NOTE: The ASC-2680 is pre-trimmed and calibrated. Adjustments may be needed after crashes.

• Forward/Backward Trim: If the drone drifts forwards or backwards, use the forward/backward trim buttons to counter the movement (see Diagram M).

Diagram M: Points to the forward/backward trim buttons on the controller.

• Bank Right/Left Trim: If the drone drifts left or right, use the left/right trim buttons to counter the movement (see Diagram N).

Diagram N: Points to the left/right trim buttons on the controller for banking.

• Spinning/Rotating Trim: If the drone spins left or right, use the left/right rotational trim buttons to counter the rotation (see Diagram O).

Diagram O: Points to the rotational trim buttons on the controller for spin adjustments.

NOTE: A short "beep" indicates one trim position. A long beep indicates the center trim position. No beeps mean maximum trim. If the drone is still unstable, resync and recalibrate.

EMERGENCY STOP: [Press] the "speed setting button" and "stunt button" simultaneously to instantly stop the drone's blades. Use this anytime you lose control.

Calibrating The ASC-2680

NOTE: Your ASC-2680 comes pre-calibrated. Recalibration may be needed after crashes or sensor shocks.

1. Place the ASC-2680 on a very flat and level surface.

2. Ensure the ASC-2680 is turned on and the controller is synced (refer to syncing pg 4). Do not start the blades. Instead, [move] both the throttle and control stick down and to the right-hand bottom corner (see Diagram P).

Diagram P: Shows moving both the throttle and control sticks down and to the right bottom corner for calibration.

If successful, the lights on the drone will rapidly flash and then stop. Once the lights stop flashing, calibration is complete.

TROUBLESHOOTING:

If lights do not flash, remove the drone battery, turn off the controller, and start over. Always [insert] the battery before turning on the controller. [Push] the left throttle stick all the way up and then down. When you hear the [beep], the ASC-2680 is resynced and ready to calibrate.

How To Perform 360° Stunt Rolls

Performing 360° stunt rolls is easy:

1. Hover the ASC-2680 in a still position with at least 6 feet of clearance above and below. Set speed to mode 2 or 3 (stunts are not possible in T Mode or Speed 1).

2. First [press] the 360 stunt button (?) on the top right of the controller. You will enter "stunt roll mode", indicated by a rapid [beeping] sound (see Diagram Q).

Diagram Q: Highlights the 360° Stunt Rolls button on the controller, indicating a rapid beep when pressed.

3. Using the right control stick, [push] directly right for a "right side roll" or directly left for a "left side roll" (see Diagram R). Always use caution when performing stunts.

Diagram R: Shows using the right control stick to perform a right-side roll (push right) or a left-side roll (push left).

NOTE: To exit stunt roll mode without flipping, [press] the stunt button again; the [beeping] will stop.

Recording Videos and Taking Photos

Your ASC-2680 is equipped with an onboard HD digital camera for video and still photographs. It can record in two places simultaneously: stream and record to your mobile device via the ASC-2680 App, and record in higher definition directly to a microSD card installed on the drone. A microSD card is not included.

MicroSD Card Recording For Highest Definition Video

• What You'll Need:
• One microSD card reader (included).
• One microSD card (not included).
• A computer with a USB port and media player capable of playing MP4 files.

Formatting Your microSD Card

Before recording, format your microSD card. [Place] the card into the included USB SD card reader and [plug] it into your computer's USB port (see Diagrams U1 and U2). An icon will appear on your desktop. Right-click the icon and follow instructions to format.

Diagram U1: Depicts inserting a microSD card into a USB reader.

Diagram U2: Depicts inserting a microSD card into a USB reader.

Installing The microSD Card In Your ASC-2680 Drone

[Place] the formatted microSD card into the ASC-2680 SD card port (see Diagram U3). [Push] gently until you hear and feel a "click".

Diagram U3: Shows the microSD card being inserted into the drone's SD card port.

Turn the ASC-2680 on and ensure it is fully charged and synced to the controller (See "HOW TO SYNC YOUR ASC-2680" on page 4).

Taking Digital Photos

To take photographs, short [press] the CAMERA button (?) on the controller. You will hear a "[beep]" and the drone's red and white LED lights will flash once.

Recording Videos

To begin recording, [press] and [hold] the CAMERA button for 2-3 seconds. You will hear a long [beep], and the red and white LED lights will flash twice and become solid, indicating recording has begun. To stop recording, [press] the CAMERA button once again. You will hear 1 [beep], and the LED lights should flash twice and become solid.

NOTE: It's recommended to test camera functions before flying.

Removing Your microSD Card

To remove the microSD card, [push] in gently on the back until you hear and feel a "clicking sound". The card will "pop-out" slightly and is ready for removal. [Pull] gently away from the port. Always store your microSD card in a clean, safe, and cool environment.

Downloading And Clearing Space On Your microSD Card

[Plug] your microSD card into the reader and connect to your computer. It is best to always [download] all videos and pictures to your computer. After downloading, follow your computer's instructions to "delete" files on your microSD card.

Installing Your Phone Holder

To use your drone's camera, install the phone holder. Turn the controller around to the back side with the battery compartment facing you. [Click] in the top "two teeth" into the two holes on the top of the controller, then [click] in the bottom (see Diagram S). To remove, [pull] from the bottom first.

Diagram S: Illustrates attaching the phone holder to the controller by clicking the top and bottom parts into place.

Camera Video and Photo Streaming Setup

Your ASC-2680 streams video and still photographs to your mobile device.

What You Will Need To Get Started Using Your Camera

• One Apple or Android smartphone* (Phone not included).
• The ASC-2680 App successfully downloaded and installed on your mobile device. App tutorial instructions are included within the application.
• To download the ASC-2680 App, [scan] the appropriate QR code below which links to the App on the Android Play Store or Apple Store. If you cannot scan, manually enter the web address located under the QR code.
• After installation, the ASC-2680 App icon should appear on your screen. [Click] the icon to run the App and ensure it installed correctly. If not, delete and repeat the process.
• Follow the "TUTORIAL" for instructions on connecting/pairing your ASC-2680 drone to the App and using it for recording film and still photos.

ICON: ASC-2680

Apple® iOS: http://app.eastgallop.com/custom/wl/asc-2680/ios.php

Android OS: http://app.eastgallop.com/custom/wl/asc-2680/google-android.php

* Apple® devices require iOS 12.0 or higher. ANDROID™ devices require OS 6.0 or higher.

If you encounter difficulties downloading the ASC-2680 App, please contact customer service at www.amaxbrands.com

IMPORTANT:

[SCAN] THIS QR CODE WITH YOUR PHONE'S CAMERA TO LEARN HOW TO USE THE ASC-2680 DRONE

Troubleshooting Your ASC-2680

Replacing The Propeller Blades

The ASC-2680's propeller system is a precision instrument that may need repair or replacement. Crash landing at high-speed may cause damage.

1. The ASC-2680 has four sets of blades: two sets with indication letters A & B on the front, and two sets with letters B & A on the rear (see Diagram T).

2. When replacing, ensure you match the indication markings/letters on the blades.

3. [Unscrew] and remove the damaged blade.

4. Replace with the correct new blade.

Diagram T:

• Front Blade Front Left = A
• Front Blade Front Right = B
• Blade Back Left = B
• Blade Back Right = A

Warnings

ASC-2680: Designed for OUTDOOR USE ONLY.

The ASC-2680 blades revolve at high speeds and can cause damage to the user, spectators, and animals. Stand away from the drone to reduce the risk of entering its flight path. Warn spectators before flying. Before flight, inspect rotor blades to ensure they are securely fastened.

• ❗ Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.
• Keep hands, hair, and loose clothing away from the propeller when the ASC-2680 is powered ON.
• Turn off the transmitter and ASC-2680 when not in use.
• The included charger is built specifically for the ASC-2680 rechargeable battery. Do not use it to charge any other battery.
• New alkaline batteries are recommended for maximum performance.
• Parental supervision recommended when flying the ASC-2680.

Battery Warnings

Rechargeable Battery

This ASC-2680 uses a rechargeable battery. If the battery no longer stays charged, dispose of it properly according to local disposal requirements.

Controller Batteries

Remote control requires 4 "AAA" batteries (not included). Please read the important battery safety warnings below.

• Always replace the whole set of batteries at one time.
• Do not mix alkaline, standard (carbon-zinc), and rechargeable batteries (Nickel Metal Hydride).
• Do not mix old and new batteries.
• Non-rechargeable batteries are not to be recharged.
• Rechargeable batteries are to be removed from the item before being charged (if removable).
• Rechargeable batteries are only to be charged under adult supervision.
• Exhausted batteries should be removed immediately and must be recycled or disposed of properly according to state or local government ordinances and regulations.
• The supply terminals are not to be short-circuited.
• Only batteries of the same or equivalent type as recommended are to be used.
• Batteries are to be inserted with the correct polarity.
• Do not dispose of batteries in a fire - batteries may leak or explode.
• This product is only to be connected to equipment bearing either of the following symbols: ⏓ or III.
• Retain the screwdriver for future use.
• Store the screwdriver where the child cannot access it.
• The screwdriver is not a toy!

Care and Maintenance

• Always remove the batteries from the wireless remote control when it is not being used for an extended period.
• To clean, gently wipe the remote control and ASC-2680 with a clean damp cloth.
• Keep the product away from direct heat or sunlight.
• Do not submerge the product in water. This can damage the unit beyond repair.
• Parental guidance recommended when installing or replacing batteries.

Limited 90-Day Warranty (North America)

AMAX Group USA warrants to the original consumer that this product is free from electrical or mechanical defects for 90 DAYS from the date of purchase. If a defect is discovered within the warranty period, AMAX Group USA will repair or replace the unit free of charge upon receipt, shipped postage prepaid and insured to our warranty center, ALONG WITH THE ORIGINAL RECEIPT evidencing purchase from an approved retailer and that the product is still within the 90-day period. The warranty covers normal consumer use and does not cover damage in shipment or failure resulting from alterations, accident, misuse, abuse, neglect, wear and tear, inadequate maintenance, commercial use, or unreasonable use. Removal of any parts/components voids all warranties. This warranty does not cover costs of repairs made or attempted outside by third parties. Any applicable implied warranties, including warranties of merchantability and fitness, are limited to 90 DAYS from the date of purchase. Consequential or incidental damages are excluded. Some states do not allow limitations on implied warranties or exclusion of damages, so the above limitations may not apply.

Repair/Replace Product

If your product malfunctions, immediately contact our warranty center. If a return is necessary, our warranty department will issue an RMA number/form and an address for shipping. AMAX reserves the right to repair, replace, or refund the product.

IMPORTANT NOTICE:

Returns not accompanied by an AMAX-issued RMA form and number will be rejected and returned to sender. Contact our warranty center before returning any product!

Preparation For Shipping Your Product:

Repack your product in a durable box, preferably the original carton, and send it prepaid and adequately insured. Include the RMA form, your daytime telephone number, and email address inside the shipping carton. If your warranty has expired and you still require service, please contact our customer care team. For further information, send all inquiries to: customercare@amaxbrands.com

IMPORTANT NOTICE! DO NOT ATTEMPT TO SHIP YOUR PRODUCT BACK WITHOUT FIRST CONTACTING OUR WARRANTY DEPARTMENT AT:

Email: customercare@amaxbrands.com