Eaton EWFFSC15 Wi-Fi Smart Fan Speed Control
Quick Start Guide
Eaton's broad selection of Wi-Fi Smart Devices offer reliability with unbeatable ease of setup. Every device sets up quickly and easily with the Brightlayer Home App – no hubs or controllers are necessary. You can add voice control using any Alexa or Google device.
For more information on the complete Wi-Fi smart product portfolio, please visit Eaton.com/smarthome.
Your Wi-Fi Smart Fan Speed Control
Control your fans from anywhere with Eaton's Wi-Fi Smart Fan Speed Control (EWFFSC15). It replaces standard switches and features ON/OFF and DIM/BRIGHT control. The EWFFSC15 can be remotely controlled using the Brightlayer Home App.
Features
- Replaces standard switches
- ON/OFF and DIM/BRIGHT control
- Remotely controlled via Brightlayer Home App
- 3 Preset fan speeds: High, Medium, Low
- Single pole & 3-way compatible
- Requires neutral wire
- Rating: 1.5A, 120V AC, 60Hz
Setup and Control
Set up and control your device using the Brightlayer Home App. Enjoy voice control with Alexa [Alexa] and Hey Google [Hey Google]. Installation is easy and requires no hub. You can also set schedules, groups, and scenes.
Note: Amazon, Alexa and all related logos are trademarks of Amazon.com, Inc. or its affiliates. Google and Google Play are trademarks of Google LLC. Wi-Fi CERTIFIED logo is a trademark of the Wi-Fi Alliance.
Installation
Tools Needed
- Phillips-head Screwdriver ?
- Wire cutters ✂️
Additional System Requirements
- A 2.4GHz Wi-Fi network with high-speed internet
- iOS 12.0 or later or Android 8.0 or later mobile device (connected to Wi-Fi and Bluetooth)
- A Brightlayer Home account set up through the Brightlayer Home App
Prior to Installation
WARNINGS AND CAUTIONS:
- Turn OFF circuit breaker or remove fuse(s) and test that power is OFF before installation process ⚠️
- Never wire any electrical device with power turned ON. Wiring the fan speed control HOT may cause permanent damage and void the warranty.
- If you are not sure about any part of these instructions, please contact a licensed electrician.
Cautions:
- Use only with 120V/AC 60Hz.
- Do not exceed the maximum rating of the fan speed control as indicated on the device.
- Must be installed and used in accordance with all national and local electrical codes.
- If a bare copper or green ground connection is not available in the wallbox, contact a licensed electrician for installation.
- Use only #14 or #12 copper wire rated for at least 75°C with these devices.
- DO NOT USE WITH ALUMINUM WIRE.
IMPORTANT: Wi-Fi Smart Fan speed control (EWFFSC15) will not work or will be damaged if wired incorrectly, and the warranty will be voided. Refer to wiring instructions provided.
NOTE: The Wi-Fi Smart Fan speed control (EWFFSC15) is wired directly to the ceiling fan fixture.
Wiring Diagram Description (Single Location Installation)
The device connects as follows:
- Black Hot (120V): Connects to the device's hot terminal.
- Load (to Ceiling Fan): Connects to the device's load terminal.
- Neutral: Connects to the device's neutral terminal.
- Green Ground: Connects to the device's ground terminal.
The device can be wired with a standard 3-way switch where a traveler wire exists for 3-way functionality.
Operation Instructions
- Press the ON button to turn the fan ON at the previously selected level.
- Press the OFF button to turn the fan OFF.
- The bottom LED indicates the fan speed controller is turned ON.
- When the fan is OFF, press and hold the ON button for 2 seconds until the LED blinks green for full fan speed.
Factory Reset
To reset the fan speed controller, excluding it from its network and restoring all factory defaults:
- Turn ON the fan speed controller.
- Press and hold the ON button for 30 seconds until the LED indicator blinks red.
- Release the button.
- The LED indicator will start flashing fast while it is being reset.
- The LED indicator will then start blinking magenta at a normal rate, indicating the fan speed controller is not part of a Wi-Fi network.
How to Download the App & Set Up Your Device
Download the App
Search and download the Brightlayer Home App via the App Store or Google Play [Google Play]. Select "Create an Account" to create an account by following the on-screen instructions.
Get your Wi-Fi Smart Device running in 3 easy steps!
STEP 1: Set-up the Device
Add your device to the Brightlayer Home App:
- Double-click the "ON" button on the Wi-Fi Smart Fan Speed Control (EWFFSC15). The Status LED should be blinking cyan to indicate it's in set-up mode. If not, refer to the Troubleshooting guide.
- Log in to your account on the Brightlayer Home App.
- Select the "Devices" option.
STEP 2: Add a Device
Next, click on the "Add a Device" option. Select the device type to add.
STEP 3: Configuration
Once selected, devices will be displayed. Additional devices can be added using the global add (+) button.
Note: Now you can utilize features like creating schedules, scenes, preset light levels, and minimum/maximum brightness settings through the Brightlayer Home App.
Troubleshooting Guide
| Symptom | Possible Cause | Solution |
|---|---|---|
| Device doesn't function. All LEDs are OFF. | A) Circuit breaker is open or tripped B) Air Gap switch on the fan speed control is pulled out C) Improper wiring D) Defective fan speed control | A) Turn ON/Close the circuit breaker. B) Push in the disconnect switch on the fan speed control. C) Check and correct wiring. D) Replace fan speed control. |
| Device functions normally using push buttons but not from Brightlayer Home App. Purple LED indicator is blinking ON and OFF about once per second. | Fan speed control is not included in the Wi-Fi network. | A) Include the fan speed control in the Wi-Fi network using Brightlayer Home App. B) Check that the router is functioning properly. C) Go through the factory reset procedure and re-add the device to the Brightlayer Home App. |
| Device functions normally using push buttons but not from Brightlayer Home App. Yellow LED indicator is blinking ON and OFF about once per second. | No Wi-Fi signal. | Check the router. |
| Device functions normally both locally and from Brightlayer Home App but can’t be controlled from the standard 3-way switch. | The 3-way wire is not connected. | Refer to the wiring connection and check if the 3-way wire is connected. |
| Fan speed control is warm to touch after a period of time. | This is normal if the load is within the fan speed control limits. | No action required. |
LED Status Quick Reference Table
| Function | Device State | Button | Number of Seconds to Press | LED Indicator Color | Default |
|---|---|---|---|---|---|
| Full speed ON/OFF | ON/OFF | ON | 2 | Green | Full speed |
| Power up state | ON | OFF | 5 | Blue | OFF |
| Level LED indicator OFF brightness | OFF | OFF | 15 | White | Level 1 |
| Level LED indicator ON brightness | ON | ON | 15 | White | Level 3 |
| Power LED indicator ON brightness | ON | ON | 20 | Yellow | Level 3 |
| Power LED indicator OFF brightness | OFF | OFF | 20 | Yellow | Level 1 |
| Factory reset | ON/OFF | ON | 30 | Red | N/A |
Wi-Fi Smart Fan Speed Control Color Change Kit Installation
The EWFFSC15 is available with color change kits.
- Pull out the air gap switch at the top of the device and then squeeze the top tabs on both sides of the device.
- Pull the faceplate off.
- Line up all tabs and snap the faceplate on, then push the air gap switch in.
Note: Not all products include color change kits.
Warranty and Compliance
End User License Agreement
Software included with the Eaton product is licensed to you. Eaton retains all title and ownership to any software. Without Eaton's authorization, you shall not copy, disclose, display, make available to others, sell, transfer, sublicense, reverse compile, disassemble, or redistribute the software. By using the software, you agree to the terms of Eaton's End User license agreement at: https://www.eaton.com/WiFiSmartEULA.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. FCC CAUTION: Any changes or modifications not expressly approved by Eaton Wiring Devices could void the user’s authority to operate the equipment.
Industry Canada Compliance
This device complies with Industry Canada’s license-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause interference; and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Eaton Wiring Devices Limited 2 Year Warranty
Eaton Wiring Devices warrants its Fan Speed Control to be free of defects in materials and workmanship in normal use and service for a period of two years from the date of original purchase. This warranty is in lieu of all other warranties. No agent, representative, or employee of Eaton has authority to increase or alter the obligations of Eaton under this warranty. To obtain warranty service, send the defective Fan Speed Control prepaid and insured to Quality Control Dept., Eaton Wiring Devices, 203 Cooper Circle, Peachtree City, GA 30269; in Canada: Eaton Wiring Devices, 5925 McLaughlin Road, Mississauga, Ontario L5R 1B8. Eaton will repair or replace the defective unit at its option. Eaton is not responsible if the defect is caused by misuse, abuse, improper installation, alteration, improper maintenance, or damage in shipment. EATON SHALL HAVE NO RESPONSIBILITY FOR INSTALLATION OR FOR ANY PERSONAL INJURY, PROPERTY DAMAGE, OR CONSEQUENTIAL DAMAGES. The exclusive remedy is repair or replacement at Eaton’s option. Implied warranties are limited to two years. Some states/provinces may have different warranty regulations.
Contact Us
For troubleshooting contact us at:
- Email: TechSupport@eaton.com
- Phone (Toll Free): 877-386-2273
- Device support: Option 5 then Option 3
- App support: Option 2 then Option 9
- Fax (Toll Free): 800-329-3055
Visit us online:
- www.eaton.com/smarthome
- Eaton.com/chat
