Eaton Wi-Fi Smart Voice Dimmer

Introduction

Congratulations on your new Eaton Wi-Fi Smart Voice Dimmer. Enjoy enhanced control over your lighting with voice commands and smart home integration.

For videos and additional information, visit: Eaton.com/SmartHome

Product Overview

The Eaton Wi-Fi Smart Voice Dimmer features:

• ON/OFF Button
• LED Indicator Bar
• Microphone
• Premium Speaker
• Air Gap Switch
• Privacy Button

Warnings and Cautions

• Always turn OFF the circuit breaker or remove fuses and test power before installation.
• Never wire any electrical device with power ON.
• Consult a licensed electrician if unsure about any part of the installation.
• Ensure proper grounding is available; contact an electrician if not.
• Use only #14 or #12 copper wire rated for at least 75°C. DO NOT USE ALUMINUM WIRE.
• Use only with 120V/AC 60Hz.
• Do not exceed the maximum rating of the dimmer.
• Must be installed and used in accordance with national and local electrical codes.
• Suitable for installation in outlet boxes measuring a minimum 3" x 2" x 2-1/2" deep.

Wiring Diagrams

Refer to the following diagrams for single-location, 3-way, and multi-location control installations.

Single Location Control Installation

Components:

• Dimmer
• Hot Wire
• Neutral Wire
• Ground Wire
• Load Wire

3-Way / Multi-Location Control Installation

Components:

• Dimmer
• Hot Wire (Common)
• Traveler Wires
• Neutral Wire
• Ground Wire
• Load Wire

For more advanced configuration parameters, such as adjusting the LED indicator bar brightness, please visit: Eaton.com/SmartHome

Operation Instructions

• Turn ON/OFF: Press the ON/OFF button.
• Disconnect Power: Pull the air gap switch.
• Quick Max: When lights are OFF, press and hold the ON/OFF button for 2 seconds to turn lights ON at maximum brightness.
• Delayed Off: When lights are ON, press and hold the ON/OFF button for 2 seconds. The lights will turn OFF after a 10-second delay, indicated by a blinking white LED bar. Press the ON/OFF button again to cancel the delay.

Factory Reset

To reset the dimmer, exclude it from its network, and restore factory defaults:

• Press and hold the Privacy button for 30 seconds.
• The LED indicator bar will slowly fade in and out orange, indicating the device is unregistered and ready for setup.

Dimmer Rating

Setup with Amazon Alexa

Get your Wi-Fi smart voice dimmer running in 3 easy steps:

1. Install your Wi-Fi smart voice dimmer according to the instructions.
2. Download the Amazon Alexa app from the App Store or Google Play.
3. Add your device to the Amazon Alexa app:
   • Select "Devices".
   • Select the "+" option to add a device.
   • Select "Add Device".
   • Select device type: Switch.
   • Select Eaton as the brand.
   • Select sub-type: Voice Dimmer Switch.
   • Follow the on-screen steps to complete the setup.

Troubleshooting

• Device not working, load does not come on, LED indicator bar not functioning:
  • Check if the breaker is ON.
  • Ensure the air gap switch is pushed in.
  • Verify wiring is correct per instructions.
• Lights are flickering:
  • Ensure wiring is correct and not loose.
  • Adjust the minimum brightness level to a higher setting via Eaton.com/SmartHome.
• Alexa is not working:
  • Ensure the device is registered in the Amazon Alexa app.
  • Check your internet connection.
  • Reboot the device by pulling and reinserting the air gap switch.
• Device unable to connect to Wi-Fi:
  • Check if the router is powered ON.
  • Verify the correct network name and password.
  • Ensure the Wi-Fi router is in a location with good signal quality.

Still having issues? Visit Eaton.com/SmartHome or contact Eaton support at 1-866-853-4293, option 2.

Warranty Information

Eaton Wiring Devices offers a 2-year limited warranty for its Wi-Fi smart devices against defects in materials and workmanship under normal use and service. This warranty is in lieu of all other warranties, expressed or implied. For full warranty details and service, please refer to the complete warranty statement or contact Eaton.