Introduction
Thank you for choosing our product. You have made an excellent choice in purchasing one of our branded products. Our products are regularly inspected to ensure that they meet the desired high quality standard and, of course, always comply with the stringent requirements of the European Union.
Important Information: Read Instructions & Keep for Future Use
Please read the instructions thoroughly and in their entirety before using the product for the first time. Keep these instructions for future reference. Should you pass the product on in future, ensure that you also include these instructions.
Safety Warnings
⚠️ CAUTION! POTENTIAL DANGER! Observe the safety information and setup instructions to avoid the risk of injury or damage to the product.
? RISK OF SUFFOCATION! Keep small parts and packaging material out of the reach of children!
?️ PRODUCT MODIFICATION Never make modifications to the product! Modifications will invalidate the warranty and the product may become unsafe or, in the worst case scenario, dangerous.
✋ DO NOT LIFT OR MOVE THE LOUNGER WHEN IT IS LOADED.
?️ Crushing hazard! Keep fingers and limbs away from moving parts.
Ensure that the folding feature are properly locked in place. ?
General Notes
We recommend at least 2 people when assembling larger pieces of furniture.
Please note that the screws are first inserted by hand and then only tightened slightly so that the screw is secure and the elements are loosely connected. Do not tighten the screws until all elements are connected in the correct way. Subsequent tightening of the screws can compensate for minor discrepancies in drill holes or weld points that can be present in hand-finished products.
Ensure that this product is fully assembled before use. Check that all screws and bolts are securely tightened, and monitor this on a regular basis.
Do not screw the screws in too tightly as the material may become damaged and cracks may form.
? ATTENTION! Keep small children away during assembly as there is a risk of injury!
Note: A creaking sound when you first sit down is quite normal; it’s simply the wood glue adapting. This will settle and is no cause for concern.
Ensure it is stable. Only use on a flat, solid and load-bearing surface. ✅
Intended Use
The lounger is designed exclusively as seating or lounging furniture for indoor and outdoor use. Use the product only for the purpose it is intended for. The manufacturer accepts no liability for damage caused by improper use. Any modification to the product may negatively impact safety, cause hazards and invalidate the warranty.
Only suitable for domestic use; not for commercial use. ?
Unpacking Instructions
Open the box and remove the product. After unpacking, please check the product for damage and to ensure it is complete. Subsequent complaints cannot be accepted.
This product is subject to rigorous testing and standards in accordance with EU directives so that we can offer you a product that is absolutely non-hazardous to your health. However, you may encounter a slight initial odour; this is not harmful to your health in any way. We recommend that you assemble the product in a well-ventilated environment. After the product has been taken out of its packaging, any odour will quickly disappear.
Maintenance and Care Instructions
Wood care instructions
Before assembly, wash the wooden parts with lukewarm water and a light soap solution to remove any wood dust, excess oil or pre-treatment residues. Then apply the oil according to your wood care product's instructions. Even natural hardwood products should be treated with wood oil on a regular basis, at least twice a year.
Before re-oiling, rub the wood with fine sandpaper and clean as previously described. Then treat according to the instructions of your wood care product as before.
Damage caused by failure to treat the wood with oil is not covered by the warranty. Changes in surface colour, greying and small cracks are normal with natural products and are not grounds for complaint. Regularly treating your natural product with oil delays this process. By following these care instructions, you will be able to enjoy your new natural product for a long time to come.
Do not place wooden furniture directly on your lawn or porous surfaces. Despite oiling, the moisture from soil and grass can lead to mould growth or similar and damage your furniture. Hardwood furniture should not be left out in the rain for long periods of time. If you use a protective oil with colour pigments, it is possible for these pigments to wash off. We accept no liability for any consequently stained surfaces.
Disposal
♻️ At the end of your item's long service life, please dispose of the valuable raw materials properly so that proper recycling can take place. If you are not sure how best to proceed, the local waste disposal companies or recycling centres will be happy to help.
Parts List
| Part No. | Description | Quantity |
|---|---|---|
| T-A | [Image shows two identical wooden side rails with pre-drilled holes and slots for slats] | 2 pcs |
| T-B | [Image shows two identical wooden base frame pieces with pre-drilled holes] | 2 pcs |
| T-C | [Image shows a wooden slat assembly, likely the main seat/backrest frame] | 1 pc |
| T-D | [Image shows a wooden slat assembly, possibly the lower backrest section] | 1 pc |
| T-E | [Image shows a wooden slat assembly, possibly the seat section] | 1 pc |
| T-F | [Image shows a wooden slat assembly, likely the main seat/backrest frame] | 1 pc |
| T-G | [Image shows two wooden support pieces for the slat assembly] | 2 pcs |
| T-H | [Image shows a metal bracket or connector piece] | 2 pcs |
| T-I | [Image shows a metal bracket or connector piece] | 2 pcs |
| T-J | [Image shows a long metal rod or support] | 1 pc |
| T-K | [Image shows two metal bracket pieces, one with a hole, one with a slot] | 4 pcs |
| T-L | [Image shows a long wooden support piece] | 2 pcs |
| T-M | [Image shows a long wooden support piece] | 1 pc |
| T-N | [Image shows a long wooden support piece] | 1 pc |
| T-O | [Image shows a U-shaped wooden frame piece] | 1 pc |
| T-P | [Image shows two curved wooden armrest pieces] | 2 pcs |
| T-1 | M4 x 12 mm screw | 20 pcs |
| T-2 | M6 x 30 mm screw | 2 pcs |
| T-3 | M6 x 50 mm screw | 18 pcs |
| T-4 | M6 x 80 mm screw | 2 pcs |
| T-5 | M6 x 25 mm screw | 12 pcs |
| T-6 | M6 x 35 mm screw | 6 pcs |
| T-7 | M8 x 25 mm screw | 2 pcs |
| T-8 | TD6 x 15 mm screw | 12 pcs |
| T-9 | LDS 25/40 x 2 mm washer | 2 pcs |
| T-10 | LDS 6/40 x 2 mm washer | 2 pcs |
| T-11 | LDS 6/20 x 1 mm washer | 2 pcs |
| T-12 | LDS 6/20 x 2 mm washer | 4 pcs |
| T-13 | LDS 6/20 x 4 mm washer | 6 pcs |
| T-14 | [Image shows a metal plate connector] | 2 pcs |
| T-15 | [Image shows a metal hinge or locking mechanism] | 2 pcs |
| T-16 | [Image shows an Allen key] | 2 pcs |
Assembly Instructions
Step 1
Attach parts T-2 and T-H to part T-I using screws T-9 and T-10. Attach part T-K to T-I. Repeat for the other side. Attach T-J to T-I. Attach T-L to T-K. Attach T-3 to T-L. Attach T-K to T-H. Attach T-3 to T-H.
Parts used: T-2 (2 pcs), T-3 (4 pcs), T-9 (2 pcs), T-10 (2 pcs), T-I (2 pcs), T-K (4 pcs), T-J (1 pc), T-L (2 pcs).
Step 2
Connect part T-A to part T-B using screws T-1. Attach part T-14 and T-15 to T-A.
Parts used: T-1 (20 pcs), T-14 (2 pcs), T-15 (2 pcs), T-A (1 pc), T-B (2 pcs).
Step 3
Attach part T-E to T-C using screws T-7. Attach part T-G to T-C using screws T-6. Attach part T-O to T-C using screws T-11. Attach part T-C to T-D using screws T-11. Attach part T-E to T-D using screws T-7. Attach part T-G to T-D using screws T-6.
Parts used: T-6 (2 pcs), T-7 (2 pcs), T-11 (2 pcs), T-C (1 pc), T-D (1 pc), T-E (1 pc), T-G (2 pcs), T-O (1 pc).
Step 4
Connect the assembled frame from Step 3 to the base structure from Step 2. Attach part T-M and T-N to the frame using screws T-3. Attach part T-D to the frame using screws T-12.
Parts used: T-3 (10 pcs), T-12 (4 pcs), T-M (1 pc), T-N (1 pc).
Step 5
Attach the main frame assembly to the base structure using screws T-5 and T-8.
Parts used: T-5 (12 pcs), T-8 (12 pcs).
Step 6
Attach the slat sections T-F and T-G to the main frame using screws T-3.
Parts used: T-3 (4 pcs), T-F (1 pc), T-G (2 pcs).
Step 7
Attach armrests T-P to the main frame using screws T-4 and T-13. Attach the backrest support T-6 to the frame using T-13.
Parts used: T-4 (2 pcs), T-6 (4 pcs), T-13 (6 pcs), T-P (2 pcs).
Step 8
Adjust the backrest angle by operating the locking mechanism. The mechanism allows for opening and closing to set different angles. Ensure the mechanism is securely locked in the desired position. ?
Step 9
Adjust the backrest angle by operating the locking mechanism. The mechanism allows for opening and closing to set different angles. Ensure the mechanism is securely locked.
Step 10
The sun lounger is now fully assembled.
For more information and service, visit: www.deubaxxl.de
